1926 Roadster interior wood replacement

Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration
Model T Ford Forum: Forum 2013: 1926 Roadster interior wood replacement
Top of pagePrevious messageNext messageBottom of page Link to this message  By Bob Santilla on Friday, January 04, 2013 - 01:15 pm:

Hello, I bought an interior wood kit from one of the big three to replace all the bad or missing wood in my 1926 Roadster. I received a box with a lot of pieces of wood and no directions as to where they go. Some pieces it was obvious as I had the old ones but it's the pieces for the seat and back of the seat I am struggling with. Do any of you have pictures of where these pieces go. Any help will be most appreciated! Thank you! Bob


Top of pagePrevious messageNext messageBottom of page Link to this message  By Tom Miller, Mostly in Dearborn on Friday, January 04, 2013 - 01:39 pm:

From the late Bruce's CD.


Also search the forum as my roadster and several others are photographed with the interiors out of the body.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Tom Miller, Mostly in Dearborn on Friday, January 04, 2013 - 01:43 pm:

from Fordwood.com


Top of pagePrevious messageNext messageBottom of page Link to this message  By Dan Treace, North FL on Friday, January 04, 2013 - 01:48 pm:

Original wood




Pictures of body and wood


Top of pagePrevious messageNext messageBottom of page Link to this message  By Dan Treace, North FL on Friday, January 04, 2013 - 01:49 pm:

Tom

That's funny :-)

We posted the same stuff.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Dan Treace, North FL on Friday, January 04, 2013 - 01:56 pm:

Bob

For fasteners, note the original wood picture. The upper tack rail uses stove bolts, countersunk heads from the outside. And longer ones thru the tack rail and the three backrest supports, with washers and sq. nuts on the inside.

The lower ends of the three backrest pieces are tapered and fit to the lower tack strip with wood screws, single slot, countersunk head. The tack rail is held to the metal seat support riser with stove bolts and sq. nuts, drilled holes vertically on the lower tack rail. Nuts go under the folded over sheet metal riser.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Gene Nelson -------Eastern Iowa on Friday, January 04, 2013 - 11:41 pm:

Could someone explain how #671 is attached?
Thanks,
Gene


Top of pagePrevious messageNext messageBottom of page Link to this message  By Dan Treace, North FL on Saturday, January 05, 2013 - 12:41 am:

Have no idea. Can't think of any reason for a wood part as tack strip under the cowl.

The kick panel cardboard is held by clips on the metal riser, and tacks into the tack strip behind the hinge pillar (wood part #606)


Top of pagePrevious messageNext messageBottom of page Link to this message  By Gene Nelson -------Eastern Iowa on Saturday, January 05, 2013 - 09:36 pm:

Thank you, Dan. I could see no purpose for those blocks, but they came with the kit.
Gene


Top of pagePrevious messageNext messageBottom of page Link to this message  By Bob Santilla on Sunday, January 06, 2013 - 01:00 pm:

I want to sincerely thank all of you who responded to this inquiry! You have no idea how much help you have been!

A piece that came with the kit (#607) marked "seat bottom" does not appear to fit any place in the car. And just for the record the #671 piece was not included in the kit.

One more question about the interior. What limits the door travel. The doors on the car rotate 180 degrees and I am afraid one day both the cowl and the door are going to bang together with enough force to damage them both.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Dan Treace, North FL on Sunday, January 06, 2013 - 02:10 pm:

Bob

Add a 'check strap' to the door hinge pillar and the door.

Vendors make leather ones, or you can make your own with webbing or invert a piece of folded over upholstery vinyl, so you double up the strength.

Tack on side under the kick panel hardboard, and screw the other side to the door under the door panel. Adjust the length prior to fastening so that the check strap does its job.

Ford Body Parts p/n 5515X Strap (door) check was used up to 1925. Think that the Improved Cars dropped that strap, haven't seen original open cars with door checks.

But maybe they were there, there is no p/n for Improved Open Cars for a check strap, the Closed cars did have a check strap, p/n1882X, held with footman loops on the interior.

Mine are vinyl, but used nickel plated oval head screws with washers, its not factory, and Dixie the '27 touring is a mutt,... but works to keep the passengers from slinging open the doors with a bang!




Top of pagePrevious messageNext messageBottom of page Link to this message  By john kuehn on Sunday, January 06, 2013 - 02:38 pm:

I have to ask the question. Was there more than one body maker that made wood for the 26-27 bodies?

Anybody know?


Top of pagePrevious messageNext messageBottom of page Link to this message  By Dan Treace, North FL on Sunday, January 06, 2013 - 04:37 pm:

John

By the Improved Car times, Ford was making all its open bodies and Coupes and Tudors, the Fordor was still outsourced to Briggs.

Those bodies were by then almost all steel, very little wood compared to the Fordor. Figure Ford made its own wood parts for the assembly line on the Improved Cars


Posting is currently disabled in this topic. Contact your discussion moderator for more information.
Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration