Raffle ticket

Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration
Model T Ford Forum: Forum 2012: Raffle ticket
Top of pagePrevious messageNext messageBottom of page Link to this message  By Bill Thompson on Wednesday, June 13, 2012 - 12:51 pm:

Where and how do I buy a raffle ticket for my new engine?


Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Wednesday, June 13, 2012 - 01:10 pm:

Buy your tickets now!

Engine Raffle
Tickets $10 each
Purchase tickets by August 15, 2012
Drawing to be held August 31, 2012

Need a new Model T engine?

Not just a new—but better than new. This is a complete engine and transmission with starter, generator, manifolds.
Ready to “drop in” and travel cross country.

The members of the Tin Lizzies of Albuquerque, under the direction of Larry Azevedo, a master engine builder and machinist, have built an engine that is being raffled. The value of the engine is in excess of $4,000.

The engine is being delivered to the Model T Museum in Richmond, Indiana
Sunday, May 20, 2012 by Neil O’Brien and will be on display.

Tickets are a mere $10 each. You do not need to be present to claim the prize.
The winner is responsible for picking up the engine.

Details: The block is a 1923 Canadian engine, serial number C445141. The engine has been re-babbitted, bored to 30 over, has new aluminum pistons,inside and outside oil lines, and rebuilt magneto. Complete rebuilt transmission has been balanced and has Kevlar bands, and a newly rebuilt generator, starter. It is painted and even has a fan installed. It has been run-in for 7 hours on a test stand.

To purchase raffle tickets, make check payable to

Tin Lizzies of Albuquerque
Larry Azevedo
PO Box 1465
Corrales, NM 87048-1465

All proceeds benefit the Model T Museum.
Thank you for supporting the new museum.

Good luck on the drawing!

Here is original link.
http://www.mtfca.com/discus/messages/257047/289391.html


Top of pagePrevious messageNext messageBottom of page Link to this message  By Fred Dimock, Newfields NH, USA on Wednesday, June 13, 2012 - 01:14 pm:

What do you mean by Your new engine?

It belongs to me - but your welcome to send the museum a donation! :-)

BTW - Did the museum set up a plan to ship the motor (at the winner's expense) if someone they lived too far away to pick it up?


Top of pagePrevious messageNext messageBottom of page Link to this message  By Seth H. Spratlin on Wednesday, June 13, 2012 - 01:40 pm:

Sounds pretty good, as long as it doesn't have a water pump on it.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Hal Schedler, Sacramento on Wednesday, June 13, 2012 - 02:32 pm:

I have dimensions for an engine stand made out of 2X10s that would hold up to shipping. Install the engine on the stand, strap it to a pallet and call a trucking company. It'll probably cost an arm and a leg. BTW, I use the stand for engine "run in" too.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Steve Tomaso - Milton,WA on Wednesday, June 13, 2012 - 06:52 pm:

Hal - how's about throwing those stand dimensions out for us "challenged wood guys" ?

That's if my wife will let me play with the table saw ! She claims that "it'd be damn tough to be a Model T mechanic with just stubs" !

Thanks !


Top of pagePrevious messageNext messageBottom of page Link to this message  By Bill Thompson on Monday, July 09, 2012 - 11:06 am:

I sent a check for raffle tickets and never received any ticket stubs. Were stubs issued?


Top of pagePrevious messageNext messageBottom of page Link to this message  By William L Vanderburg on Monday, July 09, 2012 - 11:37 am:

Yah, gimme some dimensions!!!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Monday, July 09, 2012 - 12:38 pm:

Bill

Ticket stubs # 1375-1384 mailed on 7/5/12.

Thank you very much for your participation.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Michael Duffy on Sunday, September 02, 2012 - 10:34 pm:

I would like to get the dimensions also. Thanks


Posting is currently disabled in this topic. Contact your discussion moderator for more information.
Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration