What'd you get done on the T this weekend?

Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration
Model T Ford Forum: Forum 2013: What'd you get done on the T this weekend?
Top of pagePrevious messageNext messageBottom of page Link to this message  By Dan B on Sunday, May 19, 2013 - 09:07 pm:

My dad and I pulled the inspection cover on my '23 Touring and filed rod caps in an attempt to get rid of a rod knock I've had since we got it running. This is actually our second attempt. The first time, we did #4 (what a pain!) and #2 cylinders, based on grounding the plugs. But it didn't get rid of the knock completely. So we dropped it again this past weekend and tightened all of them up. None of them had shims. Knock's all gone! Now I can run down the road without having the engine sound like it's about to fly apart!

Also, repacked the front wheel bearings while we had it up in the air.

What'd you get done?


Top of pagePrevious messageNext messageBottom of page Link to this message  By Bob McDonald-Federal Way, Wa. on Sunday, May 19, 2013 - 09:51 pm:

I completed the spark plug wireing(don't like them but they work) Repaired the Ig.Sw., added fuse. Starts easy(using dist. My choice) just need to fine tune and find sweet spots. Then around the block for a try this next week.
Always something to do, Ts and other things.

Bob


Top of pagePrevious messageNext messageBottom of page Link to this message  By Nathan Bright on Sunday, May 19, 2013 - 10:21 pm:

rebuilt my first rear end!!! with the help of a good HCCA buddy.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Stephen D Heatherly on Sunday, May 19, 2013 - 10:22 pm:

I finished a 1913 rear axle rebuild. I also replaced a brake shoe spring on the fordor.

Stephen


Top of pagePrevious messageNext messageBottom of page Link to this message  By Dave Wells on Sunday, May 19, 2013 - 10:38 pm:

All I did was replace the ancient capacitors in my coils. That got rid of all the high speed miss and the off idle hesitation too. I drove the car from Hamilton Ontario to Toronto and back, about 150 miles. The car ran perfectly.


Top of pagePrevious messageNext messageBottom of page Link to this message  By A. Gustaf Bryngelson on Sunday, May 19, 2013 - 11:08 pm:

I drove mine to a nearby village for a centennial celebration


Top of pagePrevious messageNext messageBottom of page Link to this message  By Danial - Veneta OR US Earth Solar System on Sunday, May 19, 2013 - 11:59 pm:

Sold it. (sigh)


Top of pagePrevious messageNext messageBottom of page Link to this message  By Karl Gilchrist on Monday, May 20, 2013 - 04:31 am:

I replaced the timer with one from Tony Wiltshire complete with a carbon brush - Because I am fed up with being covered in oil and not being able to see what I am doing when I work on the timer (bearing in mind that being RHD the rod attaches under the timer not on top) I removed the radiator and fan to improve access. While I am there I am going to replace the Commutator wiring harness as well -Karl


Top of pagePrevious messageNext messageBottom of page Link to this message  By John Fretschl Oshkosh Wi on Monday, May 20, 2013 - 07:37 am:

Just gave the old girl a bath, and a good detail.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Scott Conger on Monday, May 20, 2013 - 07:44 am:

made more patches





Top of pagePrevious messageNext messageBottom of page Link to this message  By Rob Heyen - Nebraska on Monday, May 20, 2013 - 08:02 am:

Not T, but continued to "fine tune" the Model K (T on steroids :-)). Now I have it o where we can shift to high at 5 mph and pull up to speed.

I'm having trouble figuring out the "high speed" adjustment on the Schebler carb.

Also, If someone has an idea, I suspect I should check plug gap (seems like not enough power at low speed, but it idles and runs at speed great).

Rob


Top of pagePrevious messageNext messageBottom of page Link to this message  By Steve osborne on Monday, May 20, 2013 - 09:07 am:

Ignored it all weekend so I could attend track meets, and church functions, been 2-3 weeks now since I've done anything, yuck.
oz


Top of pagePrevious messageNext messageBottom of page Link to this message  By John Manuel, Lafayette, La. on Monday, May 20, 2013 - 09:25 am:

Worked the rod caps down to about .002 on 1 and 2. Think the knock is gone but not ready for road test. This is on the old truck I recently acquired. Drove the coupe to the Half Fast Motoring Society breakfast Sat morning----running good!!!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Tom Miller, Mostly in Dearborn on Monday, May 20, 2013 - 09:29 am:

I reassembled my '26 transmission using Joe Bell's advice and some of Dave Huson's steel clutch disks. Joe rebabbited my fourth main and cleaned up the output shaft so everything looks real nice.

I have a real easy way to compress the clutch spring. I use a couple of parallel bars on the spring end and stick my drill press chuck into the bushing end and use the quill like an arbor press. I know my drill press wasn't designed for this purpose but it sure went together easy.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mike Hanson on Monday, May 20, 2013 - 09:57 am:

Took the 1912 to a car show and beat some more muscle cars, T birds and corvettes. Folks love seeing Model Ts. Instead of a trophy, we got a whole cooked BBQ brisket for first place...a true East Texas car show! Lol


Top of pagePrevious messageNext messageBottom of page Link to this message  By Derek Kiefer - Mantorville, MN on Monday, May 20, 2013 - 10:45 am:

Mine got a little closer to being at the front of the line to get some much-needed attention... I worked on everything but the Model T this weekend.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Herb Iffrig on Monday, May 20, 2013 - 11:39 am:

I thought about getting around to doing something, other people had different ideas.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Seth from NC on Monday, May 20, 2013 - 11:48 am:

Discovered the source of my head-bolt leak. It's the front bolt in the centerline of the head, just underneath the passenger-side ear of the water outlet. I thought the block might be cracked, or maybe I had a bad seal with the head gasket.

I actually have a small crack in the head on the edge of the flat surface where the head bolt goes. Between that flat spot and the corner where it was machined down beside the curve of the water outlet. Will post pics later.

Unfortunately I drained the coolant and pulled the head before I discovered the precise location of the leak. Oh well. I need to change the oil/fix my leaky, loose pedals/ and stop all of the hogshead leaks this week anyway.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Chris Brancaccio - Calgary Alberta on Monday, May 20, 2013 - 11:58 am:

I am working on replacing the rear outer axle seals on my Coupelet. Pulled the old leather/steel ones, cleaning out the bores to put in the neoprene type.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Steve Jelf, Parkerfield KS on Monday, May 20, 2013 - 02:37 pm:

Not a specific T, but T equipment. I've always been undelighted by my engine stand. A block or engine by itself would rotate without much trouble, but with a transmission on the engine it was just too end-heavy to rotate without a struggle. So I spent the weekend adapting the stand so it can be adjusted.


Here's the stand with just a block on it.


With no transmission, the center of gravity is
between #2 and #3, just below the water inlet, so that's where you set the pivot.


With engine and transmission together the center of gravity is at #4, so the adapter slides over to put the pivot there.


That allows easier rotation, but the transmission still makes the whole thing bottom-heavy, so turning it still takes some muscle. I intend to add a provision for a long handle for leverage to make it turn easier.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Jerry Ostbye on Monday, May 20, 2013 - 03:17 pm:

Tuesday I put bands in a friends 26 roadster, Wednesday I put shims in my rear wheel of my 26 Coupe,
Friday I went and helped on a touring,
Saturday I put my wheels back on and put my horn back on after going thru it.
Sunday I bought a 31 Model A, put a Z head on another friends TT and helped put inner and outer seals and Rocky Mt brakes on it as well. Whew I need a break !! :-)


Top of pagePrevious messageNext messageBottom of page Link to this message  By Enos Wiseman on Monday, May 20, 2013 - 06:34 pm:

Yesterday I sold my 1927 cut off touring with the home made turtle deck/rumble seat.
Leaving soon to tow another home


Top of pagePrevious messageNext messageBottom of page Link to this message  By Chris Olsen on Monday, May 20, 2013 - 06:40 pm:

Bought some things at Little Hershey and Bob's. (Bob, BTW made me a VERY happy camper, and was quite patient with me as I tried to remember everything I needed, and what it was actually called) I then cleaned out the 2nd stall of the garage and moved the body over to finish the wood strip deck. (speedster)


Top of pagePrevious messageNext messageBottom of page Link to this message  By M Philpott on Monday, May 20, 2013 - 06:42 pm:

received my new rear fenders last week so this week-end I cleaned them up, got them primed and shot them with color and I'm now waiting for the clear to dry.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Erich Bruckner, Vancouver, WA on Monday, May 20, 2013 - 07:55 pm:

Cleaned it, oiled, greased it, drove it in the Irvington Home Tour. Sure was fun.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Tim Voss on Monday, May 20, 2013 - 09:03 pm:

I went for a ride.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Scott Conger on Tuesday, May 21, 2013 - 12:49 pm:

Steve Jelf

you are the man, for crying out loud!

that's too cool. Now to add some all-thread and put a crank on that pivot adjuster and you'll be all set!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Steve Jelf, Parkerfield KS on Tuesday, May 21, 2013 - 02:41 pm:

Funny you should mention that. I thought about it, but I need to use the thing now. Maybe I'll add a crank later.


Top of pagePrevious messageNext messageBottom of page Link to this message  By James A smith on Tuesday, May 21, 2013 - 08:17 pm:

Excellent engine stand Steve.No work on the Autowa roadster but went to Little Hershey in Belvedere on Saturday. I felt it was a good turn out.Needs to be even more T stuff;sheetmetal,bodies that sort of stuff.I got some good deals,1919 hogs head,rim flaps,a high head,top irons and misc.Very friendly staff from Rockford T club.


Posting is currently disabled in this topic. Contact your discussion moderator for more information.
Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration