FS Speedster Intake Manifold and Header Plate Parts

Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration
Model T Ford Forum: Classifieds: FS Speedster Intake Manifold and Header Plate Parts
Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Friday, November 09, 2018 - 12:47 pm:

We previously listed Model T header plates, gaskets, and carburetor flanges for use when building a speedster exhaust and intake setup for your speedster. Upon doing so, we were asked if we could make a few intake manifolds like those used on our RAJO cylinder head. You can purchase the complete kit or individual kits to go with the header plate and gasket previously purchased. We also still have a few remaining header plates, gaskets, an carburetor flanges available individually like before. Supplies are very limited. This was a special small run. Purchase them while you can. Payment by PayPal (preferred) or check. PM me or call Mark Chaffin (951) 805-0928.


Complete kit with everything shown $295.00 plus $18.65 domestic flat rate shipping.



Kit #1 Intake manifold, gaskets and mounting hardware for use with our exhaust header plate. For use with a Winfield M201B carburetor or Carter BB1 $175.00 plus $13.65 domestic flat rate shipping.



Kit #2 Riser pipe, carburetor mounting flanges, gaskets, and mounting hardware. Trim pipe to length and install flanges in desired orientation. This was designed to work with our manifold $55.00 plus $13.65 domestic flat rate shipping.



INDIVIDUAL PARTS OFFERED


Model T Header Plate and Gasket. Polish grind finish to ensure they are flat. 3/8" thickness
Exhaust ports are 1 5/8" counter bored to accept standard 1 5/8" pipe. Intake ports measure 1 3/8"
$65.00 plus $13.65 domestic flat rate shipping.



Carburetor Mounting Flange. Polish grind finish to ensure they are flat. 3/8" thickness 1 5/8" counter bored to accept standard 1 5/8" pipe. Mounting holes are 3/8" and 2 15/16" center to center. Profile is for a Winfield Model M201B or Carter BB1. Price is $20.00 each plus $7.50 domestic shipping.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Friday, November 09, 2018 - 12:58 pm:

A few pics showing what the kit looks like installed. You build your headers to your liking. :-)





Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Saturday, November 10, 2018 - 12:44 am:

One complete set sold to Bill. Thanks Bill! Thanks MTFCA!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Sunday, December 02, 2018 - 09:29 pm:

Still available for a limited time. Great Christmas gift to yourself. :-)


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Monday, December 03, 2018 - 11:15 am:

BTT


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Monday, December 03, 2018 - 02:45 pm:

One complete kit sold to Willie. Thank you Willie! Thanks MTFCA!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Monday, December 03, 2018 - 05:46 pm:

Another kit sold to John in Iowa! Thanks John! Thanks MTFCA!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Tuesday, December 04, 2018 - 09:52 pm:

Header Plate and gasket sold to Steven. Thanks Steven!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Thursday, December 06, 2018 - 05:14 pm:

One Kit #2 and gaskets sold to Steve. Thanks Steve!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Sunday, December 09, 2018 - 07:15 pm:

Another header plate and gasket sold to Jerry. Thanks Jerry! Thanks MTFCA!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Tuesday, December 11, 2018 - 09:48 pm:

I only have a couple complete manifold kits remaining. Once they are gone they are gone.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Thursday, December 13, 2018 - 12:24 am:

BTT


Top of pagePrevious messageNext messageBottom of page Link to this message  By Tim Lloid on Saturday, December 15, 2018 - 10:22 am:

Btt


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Sunday, December 16, 2018 - 10:10 pm:

Still available while supplies last.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Monday, December 17, 2018 - 10:01 pm:

One header plate and gasket sold to Steve. Thanks Steve!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Wednesday, December 19, 2018 - 10:00 pm:

Another complete set sold to Tim. Thanks Tim!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Graeme Lockhart on Thursday, December 20, 2018 - 12:20 am:

Good afternoon Mark, I would be interested in one of your header plates please , however I live in Western Australia. (16 Owen Rd, Safety Bay Western Australia 6169) would you send to Auatralia and if so how much would this cost.
I am off for Xmas until end of January my personal email is gklockhart@yahoo.com.au
I will not be able to see the email that I am posting this on as it is my work one, I can pay with Paypal.
Thanks Graeme and Merry Xmas to you

Model T Header Plate and Gasket. Polish grind finish to ensure they are flat. 3/8" thickness
Exhaust ports are 1 5/8" counter bored to accept standard 1 5/8" pipe. Intake ports measure 1 3/8"
$65.00 plus $13.65 domestic flat rate shipping.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Thursday, December 20, 2018 - 11:33 am:

We just sold our last header plate and intake manifold and header plate kit. However, we do have a few manifolds, gaskets, and carburetor flanges remaining. Not sure if we will make any more in the future. We will let you know if we do. Thank you for all the interest.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Thursday, December 20, 2018 - 01:39 pm:

Ok. Disregard the previous post. We have four complete intake manifold/ header plate kits remaining (found a few hiding). We are out of the header plates.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Sunday, December 23, 2018 - 12:30 am:

Four complete sets remaining. This setup would make a great Christmas gift. Once they are gone, they area gone.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Thursday, December 27, 2018 - 10:43 am:

BTT


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Friday, January 04, 2019 - 12:43 pm:

Manifold kit sold to Steven. Thanks Steven!


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Chaffin......Corona, CA on Saturday, January 05, 2019 - 03:55 pm:

Three complete kits remaining. Once they are gone they are gone. Get them while you can.


Add a Message


This is a private posting area. Only registered users and moderators may post messages here.
Username:  
Password:

Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration