Coupe ? for Dave Sosnoski

Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration
Model T Ford Forum: Forum 2014: Coupe ? for Dave Sosnoski
Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Tuesday, June 03, 2014 - 11:13 am:

Dave
Should the "C" pillar have an indentation for the window "sill"?
Thanks


Top of pagePrevious messageNext messageBottom of page Link to this message  By Mark Gregush Portland Oregon on Tuesday, June 03, 2014 - 11:17 am:

http://fordwood.com/images/cpe23new.jpg
http://fordwood.com/images/cpe23new.jpg
http://fordwood.com/coupes.htm


Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Tuesday, June 03, 2014 - 11:30 am:

Thanks Mark for the link

part number 447 and 448 inside window sill?

What is the part number for the piece that the body panel and spring is attached to?

I am thinking the C pillar should have an indent just like the B pillar??


Top of pagePrevious messageNext messageBottom of page Link to this message  By David Sosnoski on Tuesday, June 03, 2014 - 02:39 pm:

Yes, the Quarter pillar (the one behind the quarter window)should have the same recess for the quarter garnish board that the Latch Pillar has. The Quarter Pillar does not look right - can you post some more photos of it (move the 2x4 out of the way).

Dave S.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Tuesday, June 03, 2014 - 02:58 pm:

Dave Thanks for responding. Here is another picture.
Let me know if you need more pictures.
Also what about the recess on the horizontal piece just below?


Top of pagePrevious messageNext messageBottom of page Link to this message  By Rich Stinchcomb on Tuesday, June 03, 2014 - 10:15 pm:

On my re-wooded 24 coupe, the lower horizontal piece has a similar recess that the end of the window arm can rest on. The outer sheet metal seat support (there are two, one for each end) fastens to that same lower horizontal wood piece with the recess.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Tuesday, June 03, 2014 - 10:42 pm:

Thanks Rich
Do you have a picture of the outer seat support(s)?
I want to make sure I have those pieces.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Rich Stinchcomb on Tuesday, June 03, 2014 - 11:11 pm:

Drivers (left) side:

support


Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Tuesday, June 03, 2014 - 11:18 pm:

Thanks Rich


Top of pagePrevious messageNext messageBottom of page Link to this message  By David Sosnoski on Wednesday, June 04, 2014 - 09:01 am:

Kirk,

That pillar doesn't look like any I've ever seen. I want to say it is a replacement. The pillar should end at the bottom of the window support (the bottom cross piece). There should be a metal bracket which extends down to the sill. You should be able to see 3 screw holes in the top of the sill below that pillar. The horizontal piece your pillar is bolted to should not be there. The pieces Rich shows are the correct pieces - you can also see the metal bracket on the left side of his photo.

Dave S.


Top of pagePrevious messageNext messageBottom of page Link to this message  By Kirk Peterson on Wednesday, June 04, 2014 - 09:59 am:

Dave
Thank you very much for all your information.


Posting is currently disabled in this topic. Contact your discussion moderator for more information.
Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration