Valve seat stones

Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration
Model T Ford Forum: Forum 2014: Valve seat stones
Top of pagePrevious messageNext messageBottom of page Link to this message  By John Eaton on Thursday, November 27, 2014 - 09:05 am:

Need to order new stones for BD seat grinder. What diameter stone should I order.


Top of pagePrevious messageNext messageBottom of page Link to this message  By John Eaton on Thursday, November 27, 2014 - 05:27 pm:

I have the B&d valve grinder and the the seat grinder but I don't know much about the stones I need to order stones but I am not sure about the diameter


Top of pagePrevious messageNext messageBottom of page Link to this message  By Allan Bennett - Australia on Thursday, November 27, 2014 - 05:46 pm:

John, if you are only doing side valve motors, the size of the stones is not critical. There are size limitations when working in the combustion chambers of OHV cylinder heads.

Hope this helps.

Allan from down under.


Top of pagePrevious messageNext messageBottom of page Link to this message  By joe bell on Thursday, November 27, 2014 - 06:19 pm:

I use the bdr 21 for the T blocks.


Top of pagePrevious messageNext messageBottom of page Link to this message  By John Eaton on Thursday, November 27, 2014 - 09:46 pm:

Thanks for the info. Nice car on your profile Joe


Top of pagePrevious messageNext messageBottom of page Link to this message  By John Eaton on Thursday, November 27, 2014 - 09:48 pm:

Thanks Allan, That is good to know. I have the machine but not a lot of information to go with it . Every bit helps


Top of pagePrevious messageNext messageBottom of page Link to this message  By Ed Baudoux on Thursday, November 27, 2014 - 09:53 pm:

I may have some extra stones. I bought a complete Black and Decker set a few years ago. If I do, I will send you a pair. edbaudoux -at- gmail -dot- com. Us Fordor people need to stick together. Both sides of my family came through Nova Scotia. :-)


Top of pagePrevious messageNext messageBottom of page Link to this message  By Donnie Brown North Central Arkansas on Friday, November 28, 2014 - 10:31 am:

John, do you have the "stone dresser" for the seat grinder. It is very important to dress the stones to the proper angle. I also keep 2 different "grits" of stones. (fine and medium) If doing the cast block or hard seats it is nice to have the proper "grit". I may have an extra B@D stone dresser if you need one. Ill have to look for it, so let me know if I need to go on a "search and find" mission .. :-) :-)


Top of pagePrevious messageNext messageBottom of page Link to this message  By John Eaton on Friday, November 28, 2014 - 09:34 pm:

Thanks Donnie, I bought a new stone dresser as I have read on here many times how important it is to keep the stone dressed


Top of pagePrevious messageNext messageBottom of page Link to this message  By Pat Kelly on Friday, November 28, 2014 - 11:42 pm:

John, I have a B&D valve machine and found a Army manual on it in pdf form. If you like I'll post a copy for you to grab. PK


Top of pagePrevious messageNext messageBottom of page Link to this message  By John Eaton on Saturday, November 29, 2014 - 06:07 am:

Thanks Pat, I just found that manual on line and printed it off. John


Top of pagePrevious messageNext messageBottom of page Link to this message  By Ed Baudoux on Saturday, November 29, 2014 - 03:30 pm:

John, I sent you an email. I have an extra red stone, and an extra stone dressing fixture.


Posting is currently disabled in this topic. Contact your discussion moderator for more information.
Topics Last Day Last Week Tree View    Getting Started Formatting Troubleshooting Program Credits    New Messages Keyword Search Contact Moderators Edit Profile Administration