| |
| JAN 3 | Acc. 575, Letter 389, Ford Archives |
| T-518-B Exhaust Pack Nut, T-511-B Exhaust Pipe, etc.
specified. This new design replaces the old style where the pipe fit into the
manifold. The pipe now has a flange, typical of all later Model T's.
| |
| JAN 24 | Acc. 575, Letter 394, Ford Archives |
| T-518-B Exhaust Pack Nut. "This design never used. We
have therefore marked drawing obsolete under date 1-20-13." T-518 (old
number) revised to conform to new pipe design. T-5403 Touring Car Body. "Called for reinforcing sills to be fastened to the top of the regular body sills by #14 x 2" F.H.W.S. (4 screws for each sill) the reinforcing sill to reach from the rear of the front heel board to the front of rear heel board, the sill to the 1" thick, and the sides in line with those on the regular body sill. This means of course that the rear sill plates will have to be put on top of the reinforcing sill. We have called for a filler between the reinforcing sill and the inside of circular panel at the rear edge of rear door, the filler to be nailed and glued in place." Note continues regarding the use of more nails to hold the body metal in place.
| |
| JAN 28 | Acc. 575, Letter 395, Ford Archives |
| T-5637 Body Reinforcing Bracket Bolt. "Four required,
Touring Car, 1913." T-5453 Body Reinforcing Bracket. New Drawing. "Two required, Touring Car, 1913." T-5638. Sketch showing location of Body Reinforcing Bracket. "We have made this sketch for the purpose of showing customers who are having trouble with the touring car bodies how the trouble can be overcome. The material has been ordered and we will be able to supply same in the near future. For your information will state that the construction of the body has been improved upon and undoubtedly will not need this reinforcement as soon at the change can be brought about. We will therefore order only enough material of the above parts as shown on sketch to take care of the bodies which have already been built."
| |
| FEB 4 | Acc. 509, Letter, Ford Archives |
| Runabouts supplied with turtle deck only. "No rumble
seats."
| |
| FEB 8 | Acc. 575, Letter 398, Ford Archives |
| T-4332 Hub Brake Cable. "We have changed the diameter
from 1/4" to 15/64"." Had also changed the size of the wires and
the number of wires that made up this cable.
| |
| FEB 12 | (Letter from Ford to the Chicago branch) |
| "We have decided to place an extra body bracket just
beneath the tonneau door hinge of the Touring Car body, extending from the frame
of the body sill as you will observe from blue print enclosed. We have entered
order to send you one hundred pair of these brackets and we want you to put them
on every car now in stock. It is also our object to supply larger dealers with a
quantity of these brackets so that they can install them before the cars are put
out on the road next spring. The purpose of this bracket is to stiffen the body
sill and prevent too much play in the door when the top is down, also binding in
the door when the top straps are drawn up too tightly." Installation instructions followed with hints on how to add or subtract shim washers in order to align the doors.
| |
| MAR 4 | Letter, Ford to the Cincinnati branch |
| "In attaching the Touring Car body reinforcing brackets,
be sure they are fitted 1/8" to 3/16" from the top of the frame so
that when the bolts are put in it will pull the sill down. Unless the sill is
sprung down 1/8" or so when the bracket is attached but little benefit will
be derived by the reinforcement. All bodies coming through from now on will be
fitted with heavier sills so that attachment of extra brackets will be
unnecessary."
| |
| MAR 5 | Acc. 575, Letter 404, Ford Archives |
| General description of revised muffler, now using tubes which
are spot welded together at the seams rather than being riveted as previously.
Initially the shells (tubes) would be made to conform to the size of the cast
end pieces until the supply of old stock was used up. The old diameter was
5 inches while the new one was 5-1/4 inches.
| |
| MAR 15 | Acc. 575, Letter 406, Ford Archives |
| New frame with longer rear cross-member was described. Old
parts to be used for replacement only. Notes that this frame will be used on a
number of cars initially but the number was unknown at the time.
| |
| MAR 29 | Acc. 575, Letter 410, Ford Archives |
| 1914 coil unit noted. No details as to what it was. It may have been the K-W design which became standard in 1913.
| |
| APR 5 | Acc. 575, Letter 411, Ford Archives |
| T-5464 Front Fender Peak. "This peak to be added for
fitting up the front fenders which we are now using so that they may be used on
1911 and 1912 cars. This peak nearly makes the appearance of the fenders conform
to the appearance of the fenders on the 1911 and 1912 cars. If however a
customer should call for a set of front fenders to be used for repairs, it would
not be necessary to add this peak." This peak was to be riveted in place,
using just one rivet.
| |
| APR 12 | Acc. 575, Letter 413, Ford Archives |
| Coil box parts (T-5807 through T-5857) listed but no details.
This may have been the Ford-made, K-W designed, standard coil box. Previously the coil box
assemblies were purchased outside.
| |
| APR 16 | Acc. 575, Letter 415, Ford Archives |
| T-4099 Sediment Bulb assembly. Parts listed for new
pressed-steel sediment bulb which was to be used in production and for repairs.
Old brass bulb obsoleted. In letter #419, May 3, the assembly was given part
number T-5859.
| |
| APR 27 | Acc. 509, Letter, Ford Archives |
| Windshields manufactured by Rands, Vanguard and Diamond Mfg. Co.
| |
| MAY | Acc. 575, Box 19, Ford Archives |
| Note indicates the longer rear cross-member "after
114,000 1913 cars." Other records indicate 1913 production began with 157,425 on October 1, 1912, which would make the new cross-member at or about 271,425. (May 16, 1913.)
| |
| MAY 1 | Acc. 509, Letter, Ford Archives |
| Change in valve timing, apparently made in late 1912 or early
1913, is noted in a letter to the branches.
| |
| MAY 29 | Acc. 575, Letter 423, Ford Archives |
| Some 1914 Touring body parts listed.
| |
| MAY 29 | Acc. 575, Letter 424, Ford Archives |
| T-5668 and 5669 body reinforcement for 1913 Touring body with
2-1/4" sills. T-5676 and 5677 reinforcements for bodies with 3-1/4"
sills.
| |
| JUN 4 | Acc. 509, Ford Archives |
| "218,900 to 242,300 built between April 1 and 30;
242,300 to 260,000 between May 1 and 31."
| |
| JUN 6 | Acc. 575, Letter 425, Ford Archives |
| Location of body reinforcement bolt holes changed.
| |
| JUN 12 | Letter from Ford to all branches |
| "In order that all our branches may clearly understand
the handling of complaints on present touring car bodies we submit the
following: "It is expected that you will furnish all Dealers with body sill reinforcements, wood reinforcements for the rear seat frame and also rear corner brackets as shown in the attached blue print. To make a satisfactory and permanent repair all of this material should be put in. We have found that the sills break most frequently within a few inches of the rear end and in such cases the rear corner brackets will serve to bind the sills together. The wood reinforcements in the rear seat will relieve the rear ends of the sills from all strain, consequently there is no necessity of replacing the sills on account of the wood splitting at the end. In applying the steel stamping underneath the tonneau door you will find it necessary to chisel out the wood at the lower rear corner on all Beaudett bodies and perhaps shim up other makes of bodies where the bracket spreads out at the rear. "As this body trouble is going to be more or less general perhaps you had better employ one or two good body men to do this work. We believe this will be better that to leave the work to the ordinary shop mechanics to handle. As the season advances you will probably have a great deal of this work to do and you might as well prepare for it now."
| |
| JUN 14 | Acc. 575, Letter 426, Ford Archives |
| T-1314 Hood handle. "Redesigned, and change material
from pressed steel to aluminum casting." Body brackets (5668, 5669, 5676 and 5677) revised again. Now have two bolt holes at the front end, instead of three. Also specified 5/16 x 2-1/8 inch carriage bolts to be used instead of 5/16 x 1-1/2 inch lag screws be used. (Step bolts were specified instead of carriage bolts in later notes regarding these brackets.)
| |
| JUN 28 | Acc. 575, Letter 430, Ford Archives |
| Noted changes in the transmission cover door material (not in
the design). Stated that the cover door is to be "pickled and
annealed." No mention of paint. The finish had been mentioned in previous
letters, and was the same as in this letter.
| |
| JUL 1 | Acc. 575, Letter 431, Ford Archives |
| Many notes on 1914 Touring body which would seem to indicate
that this body was now used in production.
| |
| JUL 5 | Acc. 509, Letter, Ford Archives |
| 260,000 to 282,700 built June 1 to 30. Note: These numbers are the number of engines built at the main Ford plant. Engines with these serial numbers were built on May 1913. The variance was due to the 12,247 B-numbered engines used in the last three months of 1912 (beginning of fiscal 1913 production).
| |
| JUL 10 | Acc. 575, Letter 433, Ford Archives |
| T-4099 Pressed-steel sediment bulb and its components
apparently never used. Brass bulb and parts were again specified for production,
as apparently they had always been. Noted that gasoline tanks which had been
built to accommodate the pressed-steel bulb could be repunched and by using a
larger reinforcement (T-4097) to cover the holes these tanks could be used with
the brass bulb.
| |
| JUL 14 | Acc. 575, Letter 434, Ford Archives |
| Noted that 1913 Touring bodies were made by Herbert, Fisher,
Wilson, and Beaudett. Apparently the Beaudett bodies differed in construction
from the others. Beaudett bodies with a filler block on the rear door hinge
posts apparently did not need the steel reinforcing pieces.
| |
| JUL 14v | Acc. 509, Letter, Ford Archives |
| 1913 cars used new style exhaust manifold and pipe. (Pipe now
has the flanged end.) "Babbitt driveshaft bearing used in first 18,000 cars." (1909-10)
| |
| JUL 16 | Acc. 575, Ford Archives |
| "Engine 300,000 built at 1:25 P.M." (Engine
production records indicate this was built on June 26, 1913. This was the 300,000th engine
built at the main Ford plant, NOT serial number 300,000. The variation is due to the 12,247
B-numbered engines used in the last three months of 1912.)
| |
| JUL 28 | Acc. 509, Letter, Ford Archives |
| "1914" prices effective August 1, 1913: Touring,
$550. Runabout, $500. Town Car, $750.
| |
| JUL 28 | Acc. 833, Photo 75, Ford Archives |
| Photo of 1914-type Touring body with 1913 windshield, and wheels which
are striped. (No body striping.)
| |
| JUL 30 | Acc. 575, Letter 439, Ford Archives |
| New design of turtle deck on Torpedos (Runabouts) noted for
1914 models. This was probably the change from the "square" corners to
the rounded ones. Also a note under Gas Lamp brackets noted, "and since we
are contemplating the use of electric headlamps, we would not use more of these
brackets ...."
| |
| AUG 4 | Acc. 575, Letter 440, Ford Archives |
| T-528-B Starting Crank Ratchet. "We have redesigned the
shape of the notches, and to show the new design we have added special sketch
giving the development of the outside surface of notches when bent in place. We
ask that you kindly call the attention of the people who are to make these
ratchets to the fact that this sketch does not show the correct shape of these
notches when in the blank before being drawn, which shape will have to be
determined by cutting and trying....." The note continues but seems to indicate that the pressed steel ratchet was still being used.
| |
| AUG 5 | Acc. 509, Letter, Ford Archives |
| 282,700 to 298,200 built July 1 to 31.
| |
| AUG 29 | Acc. 575, Letter 446, Ford Archives |
| T-1215 Muffler asbestos. "Removed note specifying this
asbestos to be dyed black."
| |
| SEP 4 | Acc. 509, Letter, Ford Archives |
| 298,200 to 306,800 built August 1 to 30. (See notes under July 5 and
July 16 above.)
| |
| SEP 27 | Acc. 575, Letter 450, Ford Archives |
| T-55 Brake Shoe revised to be made in one piece again.
| |
| OCT 13 | Acc. 1701, Box 3, Ford Archives |
| Added "T-8 (nut) Two required as radius rod ball cap
nuts." (Studs and nuts replaced the screws used previously.)
| |
| OCT 18 | Acc. 575, Letter 455, Ford Archives |
| T-800-D Crankcase. Noted changes made earlier in which the
separate drain cup had been replaced by just stamping the crankcase instead.
(The "drain cup" refers to the "teacup" pan used until
sometime in 1913.)
| |
| NOV 4 | Acc. 509, Letter to all branches, Ford Archives |
| 306,800 to 314,800 built September 1 to 30. (See notes under July 5 and
July 16 above.) Announced that speedometers will no longer be supplied on cars for a few
months, and that a credit of $6 will be allowed on the price of the car. They said that
as soon as a satisfactory replacement unit was found, they would supply it at the $6 price
for installation on customer's cars. Furthermore, the branches would not be
allowed to buy speedometers for customers.
| |
| NOV 18 | Acc. 509, Letter, Ford Archives |
| 60-inch tread to be discontinued. (But wasn't.)
| |
| NOV 24 | Letter from Ford to the Denver branch) |
| "Kindly give us by return mail your present inventory of
the following: T-5668 reinforcement, right T-5669 reinforcement, left T-5675 rear seat frame reinforcement T-5678 rear corner bracket." These are the 1913 touring body reinforcement parts.
| |
| FROM: Ford Motor Company, Detroit Office December 2, 1913 The following is a revised list of paints and our new numbers for same, kindly order all paints by these numbers: | |
| F-101 | 1763 | First Coat Elastic Black Japan, Fenders and Shields |
| F-102 | 1001 | Second Coat Black Japan, Fenders and shields |
| F-103 | 258 | First Coat Blue Dipping, Hoods & Rear Axles |
| F-104 | 1355 | Second Coat Quick Drying Black, Rear Axles |
| F-105 | 40 | First Coat Brushing Black Japan, Front Axles |
| F-106 | 459 | Second Coat Brushing Black Japan, Front Axles |
| F-107 | 450 | Blue Black Baking, Coil Box |
| F-108 | 1843 | First Coat Black Wheel Surfacer, Wheels |
| F-109 | 260 | Second Coat Blue Color Varnish, Wheels |
| F-110 | 417 | Second Coat Black Brushing, Frame |
| F-111 | 488 | First Coat Red Baking Metal Body Primer, Body |
| F-112 | 66 | Black Glaze Putty — Second Operation Body, Body |
| F-113 | 948 | Second Coat Blue Ground, Body |
| F-114 | 619 | Solid Rubbing Body Blue, Repairs only |
| F-115 | 480 | 3rd & 4th Coat Body Spraying Blue Color Varnish, Body |
| F-116 | 908 | 5th Coat Black Striping Color, Not used regularly |
| F-117 | 1435 | Fine French Gray Deep Striping, Wheels |
| F-118 | 1761 | Oil Proof Steel Blue, Painting Machines |
| F-119 | 896 | Black Engine Dipping, Finishing Crank Cases |
| F-120 | White Cold Water Paint | |
| F-121 | Ivory Drop Black "E" | |
| F-122 | Black Radiator Paste | |
| This list supersedes all previous ones that we have mailed you. Ford Motor Company Manufacturing Department
| ||
| DEC 9 | Acc. 575, Letter 462, Ford Archives |
| Noted that the 1/2" pipe plugs used for water jacket
seals were no longer used.
| |
| DEC 27 | Acc. 575, Letter 463, Ford Archives |
| T-543-B Oil Tube. Now specified as having mounting ear integral with the
funnel instead of the separate clamp. The clamps would continue to be made until the supply
of old tubes was used up.
| |
|
GO TO 1912 GO TO 1914
| |
| © Bruce W. McCalley. Rev. February 20, 2007 | |