Search found 684 matches
- Wed Feb 14, 2024 4:09 pm
- Forum: General Discussion Forum
- Topic: Why are my head bolts different lengths?
- Replies: 5
- Views: 516
Re: Why are my head bolts different lengths?
I checked and they looke to be the same length, but the threads are different lengths. I cleaned and ran a tap through all the holes
- Wed Feb 14, 2024 2:23 pm
- Forum: General Discussion Forum
- Topic: Why are my head bolts different lengths?
- Replies: 5
- Views: 516
Why are my head bolts different lengths?
My head bolts are different lengths, is that ok?
- Wed Feb 14, 2024 12:28 pm
- Forum: General Discussion Forum
- Topic: Tightening head bolts and gasket protocall
- Replies: 12
- Views: 732
Tightening head bolts and gasket protocall
I am putting a new head gasket on my t and I had a few questions:
1. What order do I tighten them in?
2. How much do I tighten them?
3. Do I put anything on the head gasket before installation?
1. What order do I tighten them in?
2. How much do I tighten them?
3. Do I put anything on the head gasket before installation?
- Fri Oct 13, 2023 8:50 pm
- Forum: General Discussion Forum
- Topic: How does this look?
- Replies: 19
- Views: 1785
Re: How does this look?
It was running fantasticly with excellent compression before. I don't plan to put more than 1 or 2 hundred miles on it a year. And yes, I don't have the time or resources to rebuild it at this time. Also, does anyone have a set of used acceptable newer style valves they would sell? I'll put an add i...
- Thu Oct 12, 2023 11:36 am
- Forum: General Discussion Forum
- Topic: How does this look?
- Replies: 19
- Views: 1785
Re: How does this look?
thankfully the valves sick out, and look good, I plan to lap them though. How does the scoring on the cylinder wall look?
- Thu Oct 12, 2023 8:19 am
- Forum: General Discussion Forum
- Topic: How does this look?
- Replies: 19
- Views: 1785
Re: How does this look?
What do you mean by valve seats?
- Sun Oct 08, 2023 8:47 am
- Forum: General Discussion Forum
- Topic: How does this look?
- Replies: 19
- Views: 1785
Re: How does this look?
Only one I have now, will get some more when I get home.
- Sun Oct 08, 2023 8:18 am
- Forum: General Discussion Forum
- Topic: How does this look?
- Replies: 19
- Views: 1785
Re: How does this look?
Also, there is some scoring on the cylinder wall. Is that a problem?
- Sun Oct 08, 2023 8:14 am
- Forum: General Discussion Forum
- Topic: How does this look?
- Replies: 19
- Views: 1785
Re: How does this look?
Thanks for the advice! Where is the least expensive place to get valves? Langs has them for 9 dollars apiece.
- Fri Oct 06, 2023 7:53 pm
- Forum: General Discussion Forum
- Topic: How does this look?
- Replies: 19
- Views: 1785
How does this look?
Just pulled the head for the first time, does this look bad?
- Fri May 12, 2023 7:59 am
- Forum: General Discussion Forum
- Topic: Luray assistance
- Replies: 0
- Views: 411
Luray assistance
Although I am coming to Luray this year, I don't have enough parts to sell to justify buying a space, and I was wondering if a vendor at luray would be willing to sell me a small portion of their space so I can put a four foot table in it? Should have posted this alot earlier, just plumb forgot with...
- Sun Jan 22, 2023 12:40 am
- Forum: OT - Off topic
- Topic: very off topic: 2 dollar bills bad luck?
- Replies: 29
- Views: 2940
Re: very off topic: 2 dollar bills bad luck?
I sure wish the dollar was backed by something solid like the good old days when you could trade in your bill for gold.
- Fri Jan 20, 2023 9:50 pm
- Forum: OT - Off topic
- Topic: very off topic: 2 dollar bills bad luck?
- Replies: 29
- Views: 2940
Re: very off topic: 2 dollar bills bad luck?
If you are referring to the 90% silver dollar coins, I have collected a dozen or so.
- Fri Jan 20, 2023 7:49 pm
- Forum: OT - Off topic
- Topic: very off topic: 2 dollar bills bad luck?
- Replies: 29
- Views: 2940
very off topic: 2 dollar bills bad luck?
When I go through a drive through in my T, I usually pay in 2 dollar bills and half dollars. The reactions can get pretty amusing. Anyways, I was at the dollar general not 30 min ago, and handed the cashier 2 two-dollar-bills. She wanted to keep them and asked the manager how she could do that. The ...
- Mon Dec 12, 2022 1:16 pm
- Forum: OT - Off topic
- Topic: Have you ever wondered bout these things?
- Replies: 38
- Views: 3171
Re: Have you ever wondered bout these things?
Brilliant! That is an unfortunately accurate representation of the US now.
- Tue Oct 25, 2022 8:53 pm
- Forum: Classifieds - Parts
- Topic: Model T 26-27 Touring Top Bow Irons For Sale Removed From Listing
- Replies: 1
- Views: 961
Re: Model T 26-27 Touring Top Bow Irons For Sale
I would like to buy these, I already sent you an email and p.m. please call me at the number I sent.
- Sun Oct 23, 2022 9:20 pm
- Forum: Classifieds - Parts
- Topic: WTB '26-'27 touring top bows/irons
- Replies: 4
- Views: 1113
Re: WTB '26-'27 touring top bows/irons
Still looking
- Mon Jun 06, 2022 11:23 am
- Forum: General Discussion Forum
- Topic: Who is Howard Thompson?
- Replies: 5
- Views: 1137
Who is Howard Thompson?
Who is Howard Thompson? I somehow have his card and don't know were I got it.
- Fri Jun 03, 2022 9:44 am
- Forum: General Discussion Forum
- Topic: Youth foundation engine raffle
- Replies: 3
- Views: 1020
Re: Youth foundation engine raffle
I got my ticket, maybe I will get lucky!
- Fri Jun 03, 2022 9:33 am
- Forum: Classifieds - Parts
- Topic: WTB '26-'27 touring top bows/irons
- Replies: 4
- Views: 1113
Re: WTB '26-'27 touring top bows/irons
still looking, i am located in northeast tn
- Fri Jun 03, 2022 8:09 am
- Forum: General Discussion Forum
- Topic: Aluminum Radiator?
- Replies: 32
- Views: 3477
Re: Aluminum Radiator?
My two cents on what it takes to use an aluminum radiator ,all I did is move the output and input spouts andmove the mounting tabs lower, and put on a dowel attach to the steel rod to attach the cowel. And I learned how to weld aluminum that day too! A man at my church is a professional welder and w...
- Thu Jun 02, 2022 12:46 pm
- Forum: General Discussion Forum
- Topic: Aluminum Radiator?
- Replies: 32
- Views: 3477
Re: Aluminum Radiator?
I have had a lot of success with my aluminum radiator, give me a holler if you decided to get one and I'll let you know what I did to make it work.just shoot me an email at my email address below.
- Thu Jun 02, 2022 12:41 pm
- Forum: General Discussion Forum
- Topic: Help! I am baffeled!
- Replies: 10
- Views: 1577
Re: Help! I am baffeled!
Also,I didn't know that and made one man top irons before 1926!
- Thu Jun 02, 2022 12:40 pm
- Forum: General Discussion Forum
- Topic: Help! I am baffeled!
- Replies: 10
- Views: 1577
Re: Help! I am baffeled!
Thank you all so much for your help! Now that I have acertained that the rusty ones are not 26 27 touring one-man top iron's, I'll continue my search. thank you!
- Thu Jun 02, 2022 9:33 am
- Forum: General Discussion Forum
- Topic: Help! I am baffeled!
- Replies: 10
- Views: 1577
Help! I am baffeled!
I am trying to obtain a set of top irons for my 26/27 touring. I have located a set, but they look different than another set i saw. Any ideas what i am missing? or are there different variations of the one man top for the improved touring?
- Thu Jun 02, 2022 9:25 am
- Forum: Classifieds - Parts
- Topic: WtB cutout pedal
- Replies: 1
- Views: 578
Re: WtB cutout pedal
i got a few, i will send you a pic soon
- Thu May 26, 2022 10:18 am
- Forum: Classifieds - Parts
- Topic: WTB '26-'27 touring top bows/irons
- Replies: 4
- Views: 1113
Re: WTB '26-'27 touring top bows/irons
Sorry, not selling, wanting to buy (WTB)
- Wed May 25, 2022 8:49 am
- Forum: Classifieds - Parts
- Topic: WTB '26-'27 touring top bows/irons
- Replies: 4
- Views: 1113
WTB '26-'27 touring top bows/irons
WTB '26-'27 touring top bows/irons
- Mon May 16, 2022 9:25 am
- Forum: General Discussion Forum
- Topic: Can of worms officially opened
- Replies: 48
- Views: 4564
Can of worms officially opened
What have your experiences with marvel's mystery oil been?
- Sun May 15, 2022 8:36 pm
- Forum: Classifieds - Vehicles
- Topic: FS Unrestored Time-capsule
- Replies: 41
- Views: 13894
Re: FS Unrestored Time-capsule
I will give you 5bucks and a rusty rear axle housing for it.. Free shiping, right?
- Thu May 12, 2022 8:50 pm
- Forum: General Discussion Forum
- Topic: Luray Mini-tour?
- Replies: 2
- Views: 955
Re: Luray Mini-tour?
If anyone is interested in going to lunch on Friday, let me know, call me at4239003544
- Wed May 11, 2022 7:32 am
- Forum: Classifieds - Parts
- Topic: WTB Radiator inlet
- Replies: 5
- Views: 958
Re: WTB Radiator inlet
I might be able to hlep,, will you be at luray?
- Tue May 10, 2022 8:52 pm
- Forum: General Discussion Forum
- Topic: Calling all knowledgeable 26/7 Touring Wood People!!
- Replies: 7
- Views: 1336
Re: Calling all knowledgeable 26/7 Touring Wood People!!
I am, but I will not be able to help since I am as clueless as you are.
- Mon May 09, 2022 10:56 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Re: Unbelievable!
Just asking, with the spark advance all the. way up, is it even possible for it to backfire?
- Mon May 09, 2022 10:50 pm
- Forum: General Discussion Forum
- Topic: Not again!...
- Replies: 7
- Views: 1142
Re: Not again!...
Clean as a whistle andcoated with a thin layer of oil
- Mon May 09, 2022 3:58 pm
- Forum: General Discussion Forum
- Topic: Not again!...
- Replies: 7
- Views: 1142
Not again!...
So i pulled the oil pan to see what was under there and when i went to put it back on , i realized that there were 3 bolts about a quarter inch longer than the rest. Where do they do?
- Mon May 09, 2022 3:51 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Re: Unbelievable!
I am using an older version of the ecct
- Mon May 09, 2022 12:12 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Re: Unbelievable!
I just adjust the carburetor and when I gave it a 1/4 turn on mag, after choking it for two turns, it started right up!
- Sun May 08, 2022 9:37 pm
- Forum: Classifieds - Parts
- Topic: 27 touring to irons
- Replies: 0
- Views: 521
27 touring to irons
Does anyone have a set of touring top irons their selling that could bring to luray Swapmeet?
- Sun May 08, 2022 9:19 pm
- Forum: General Discussion Forum
- Topic: Junk in head
- Replies: 2
- Views: 852
Re: Junk in head
ok, thanks
- Sun May 08, 2022 9:18 pm
- Forum: General Discussion Forum
- Topic: oil pan
- Replies: 9
- Views: 1434
Re: oil pan
So no need to take off the oil pan cover?
- Sun May 08, 2022 9:17 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Re: Unbelievable!
I once made the mistake of cranking a hot engine with the spark and gas in idling position. due to the advice of experenced model ters, i had made sure to always have good hand and arm position so that that time when it started runnning backwards, spining the crank like a windmil, i didnt get a brok...
- Sun May 08, 2022 8:57 pm
- Forum: General Discussion Forum
- Topic: oil pan
- Replies: 9
- Views: 1434
oil pan
The oil pan on my touring hasn't been removed for at least 40 years, should i drain the oil and take it off and then clean up in there?
- Sun May 08, 2022 8:56 pm
- Forum: General Discussion Forum
- Topic: Junk in head
- Replies: 2
- Views: 852
Junk in head
Is there any problem with some black residue and junk when i look through the spark plug hole?
- Sun May 08, 2022 8:55 pm
- Forum: General Discussion Forum
- Topic: Spark gap?
- Replies: 11
- Views: 1575
Spark gap?
Posting a few random questions this evening, What is the proper gap for the spark plug?
- Sun May 08, 2022 8:53 pm
- Forum: General Discussion Forum
- Topic: Luray Mini-tour?
- Replies: 2
- Views: 955
Re: Luray Mini-tour?
Or maybe an early breakfast friday or saturday?
- Sun May 08, 2022 8:51 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
- Sun May 08, 2022 8:50 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Re: Unbelievable!
Wait until someone asks you to demonstrate cranking! You will turn on the key and get a free start. Or you will crank and crank and no start. Finally use the starter and it starts right up. They usually crank start fine if you are alone or with someone in the family or close friends, but if a stran...
- Sun May 08, 2022 8:49 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
- Sun May 08, 2022 8:47 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Re: Unbelievable!
Not as fun, and plus, neither my starter or generator works.
- Sun May 08, 2022 8:47 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Re: Unbelievable!
Wait until someone asks you to demonstrate cranking! You will turn on the key and get a free start. Or you will crank and crank and no start. Finally use the starter and it starts right up. They usually crank start fine if you are alone or with someone in the family or close friends, but if a stran...
- Sun May 08, 2022 5:55 pm
- Forum: General Discussion Forum
- Topic: Unbelievable!
- Replies: 28
- Views: 3585
Unbelievable!
As I did my 100 miles checkup on my t, I decided to adjust my coils and clean my pluggs.. Now my car usually starts in a few pulls with a little choke on bat, but never could hand start on mag. After the previously mentioned adjustments, it started so well on bar that I thought I'd try mag. So I set...
- Sat May 07, 2022 5:43 pm
- Forum: Classifieds - Parts
- Topic: Top Bows
- Replies: 8
- Views: 1675
Re: 26/27 Top Bows
wil you be at luray?
- Sat May 07, 2022 5:18 pm
- Forum: General Discussion Forum
- Topic: "What to Carry" revisited
- Replies: 21
- Views: 2568
Re: "What to Carry" revisited
I am probably overprepared, but my list is as follows: standard socket set 2 modern crescent wrenches 2 antique large adjustable wrenches 10 feet of coper wire medium flat head screw driver small flat head screw driver medium Philips head screw driver a phone charging brick and phone some standard s...
- Sat May 07, 2022 4:00 pm
- Forum: General Discussion Forum
- Topic: Luray Mini-tour?
- Replies: 2
- Views: 955
Luray Mini-tour?
Would anyone be interested in going for around an hour drive around Luray sometime on the 13 or 14, possibly grabbing some ice-cream on our way?
- Tue Apr 26, 2022 12:55 pm
- Forum: Classifieds - Parts
- Topic: SUPER SALE
- Replies: 35
- Views: 8087
Re: SUPER SALE
Will you be at the luray meet?
- Sat Mar 05, 2022 9:15 am
- Forum: General Discussion Forum
- Topic: Wheel dollies
- Replies: 15
- Views: 2667
Re: Wheel dollies
they work great until the swivels start getting gummed up, but some penetrateing oil fixes it
- Tue Jan 04, 2022 9:44 am
- Forum: Classifieds - Parts
- Topic: Looking to buy or trade: 27 touring top irons
- Replies: 1
- Views: 805
Looking to buy or trade: 27 touring top irons
I am looking for a set of 27touring top irons, or an uncomple set to mix and match with mine.
- Fri Dec 31, 2021 3:49 pm
- Forum: General Discussion Forum
- Topic: Help!
- Replies: 5
- Views: 1090
Help!
Okay, so I am completely baffled. A few weeks ago my Magneto completely stopped working even though it is still out putting power. I think somehow it is grounded but I don't know why it is still out putting power then. Any thoughts? I have tested everything I know to do with a voltmeter.
- Wed Dec 29, 2021 9:27 am
- Forum: General Discussion Forum
- Topic: Ok, so how much breaking do I really need?
- Replies: 31
- Views: 3240
Re: Ok, so how much breaking do I really need?
ok, so i locked up the rear wheels using the service brake. i avoid major roads and use my breaks only if i am coming to a complete stop.
- Tue Dec 28, 2021 9:17 am
- Forum: General Discussion Forum
- Topic: Ok, so how much breaking do I really need?
- Replies: 31
- Views: 3240
Re: Ok, so how much breaking do I really need?
Just saying, my bands haven't been changed for at least 40 years
- Tue Dec 28, 2021 8:33 am
- Forum: General Discussion Forum
- Topic: Ok, so how much breaking do I really need?
- Replies: 31
- Views: 3240
Ok, so how much breaking do I really need?
So I I have been planning to install some Rocky mountain breaks in my car. Recently I found out an interesting problem. My original brakes have so much stopping power I can lock up the rear wheels. Would a better upgrade be to get wider Wheels? Mabey Chevy ones?
Also, I dont have an aux transmission.
Also, I dont have an aux transmission.
- Sat Dec 25, 2021 10:53 pm
- Forum: OT - Off topic
- Topic: SP-4274 over Donner Pass
- Replies: 14
- Views: 2510
Re: SP-4274 over Donner Pass
Does anyone have a picture of the kind of eingine?
- Mon Dec 20, 2021 10:18 am
- Forum: General Discussion Forum
- Topic: Hcct help
- Replies: 7
- Views: 1684
Re: Hcct help
Mr Scott, I will.
Mr Simmering, email sent.
Mr Simmering, email sent.
- Fri Dec 17, 2021 7:21 pm
- Forum: General Discussion Forum
- Topic: Ok.... I am baffled!
- Replies: 10
- Views: 1891
Ok.... I am baffled!
I have been told, in my short 1.75 years of model Ting, that it is virtually impossible to start an unrestored eingine on mag. But recently I have heard of quite a few folks that were able to. So, what is the case?
- Fri Dec 17, 2021 2:00 pm
- Forum: General Discussion Forum
- Topic: Hcct help
- Replies: 7
- Views: 1684
Hcct help
Is there anyone in or near kingsport TN with a HCCT tester who could help me adjust my coils? I would be glad to reimburse them for their time and use of machine.
- Sat Dec 04, 2021 9:13 pm
- Forum: OT - Off topic
- Topic: Welding fun
- Replies: 32
- Views: 5116
Re: Welding fun
What is mag flux and ndi?
- Sat Dec 04, 2021 12:58 pm
- Forum: OT - Off topic
- Topic: Welding fun
- Replies: 32
- Views: 5116
Re: Welding fun
Thank you for the warning Dropacent. I have been riding gocart since was 10 and I understand the dangers and have prioritized saftey. Did your friends gocart have rolbars? Also, I have an eingine cutout system and front and rear brakes. I will heed your warning and be carefull.
- Tue Nov 30, 2021 11:58 am
- Forum: OT - Off topic
- Topic: Welding fun
- Replies: 32
- Views: 5116
Re: Welding fun
I have a 220 volt AC DC machine. It is a primeweld. The majority of my welding was done indoors until it became too big to work inside. I fabricated each section indoors and then welded them together outside. I have a flux core Mig, but I prefer the control of the Tig. Also, it does not leave any sl...
- Tue Nov 30, 2021 7:37 am
- Forum: OT - Off topic
- Topic: Welding fun
- Replies: 32
- Views: 5116
Re: Welding fun
My current project, all from an old bedframe and rebar scraps:
- Sat Nov 13, 2021 8:47 pm
- Forum: OT - Off topic
- Topic: Welding fun
- Replies: 32
- Views: 5116
Re: Welding fun
What do I use the different polarity for?
- Sat Nov 13, 2021 2:29 pm
- Forum: OT - Off topic
- Topic: Welding fun
- Replies: 32
- Views: 5116
Welding fun
I just got a tig welder the other day and am working on how to use it, any tips?
Jonah D'Avella
Jonah D'Avella
- Thu Nov 04, 2021 8:37 am
- Forum: Classifieds - Parts
- Topic: Wtb aluminum filler neck
- Replies: 9
- Views: 1827
Re: Wtb aluminum filler neck
Thank you all for your help, I will be buying the one on ebay!
- Tue Nov 02, 2021 7:53 am
- Forum: Classifieds - Parts
- Topic: Wtb aluminum filler neck
- Replies: 9
- Views: 1827
Re: Wtb aluminum filler neck
Ok, the only problem with that is that it doesn't have the spread out base like the original, It needs that to hold the radiator shell in place.
- Mon Nov 01, 2021 2:39 pm
- Forum: General Discussion Forum
- Topic: Back and driving!
- Replies: 10
- Views: 1916
Re: Back and driving!
So, should I put one of those thermostat things in?
- Mon Nov 01, 2021 1:36 pm
- Forum: General Discussion Forum
- Topic: Back and driving!
- Replies: 10
- Views: 1916
Re: Back and driving!
Why would I want it to run hotter? The top is about 170 to 185
- Mon Nov 01, 2021 12:34 pm
- Forum: Classifieds - Parts
- Topic: Wtb aluminum filler neck
- Replies: 9
- Views: 1827
Wtb aluminum filler neck
I need an aluminum filler neck.
- Mon Nov 01, 2021 12:33 pm
- Forum: General Discussion Forum
- Topic: Back and driving!
- Replies: 10
- Views: 1916
Back and driving!
Over the last few months, I have been troubleshooting my radiator. When I was driving it beforehand, it started constantly boiling over after about 5 or 10 minutes of driving. Most of the tubes were filled up with rust and other junk. I took it to a radiator shop and he did the best he could but cou...
- Sun Oct 10, 2021 2:06 pm
- Forum: OT - Off topic
- Topic: Stick welding aluminum
- Replies: 11
- Views: 2672
Re: Stick welding aluminum
Thank you all for the advice, based on the tips, i am going to get a professional ti di it with the right welder.
- Tue Oct 05, 2021 6:14 am
- Forum: OT - Off topic
- Topic: Stick welding aluminum
- Replies: 11
- Views: 2672
Re: Stick welding aluminum
ok, did it weld well though?
- Mon Oct 04, 2021 5:43 pm
- Forum: OT - Off topic
- Topic: Stick welding aluminum
- Replies: 11
- Views: 2672
Re: Stick welding aluminum
I got a part for my car that needs some adjustments made, not that big but they need to be fairly strong. I can't afford to buy another welder, and I I am kind of proficient with stick welder that I have.
- Mon Oct 04, 2021 6:34 am
- Forum: OT - Off topic
- Topic: Stick welding aluminum
- Replies: 11
- Views: 2672
Stick welding aluminum
Has anyone here successfully welded aluminum with a standard stick welder? if so, does it work well?
- Wed Sep 08, 2021 3:06 pm
- Forum: Classifieds - Parts
- Topic: $455 LARGE DRUM 1926 ROCKY MOUNTAIN BRAKES FOR SALE
- Replies: 8
- Views: 2709
- Sat Sep 04, 2021 9:04 am
- Forum: Classifieds - Parts
- Topic: SOLD NEW Turn Signal Kit 6v without lights
- Replies: 4
- Views: 1449
Re: NEW Turn Signal Kit 6v without lights
Is this just the switch mechanism?
- Sat Sep 04, 2021 9:02 am
- Forum: General Discussion Forum
- Topic: Crank counterweights
- Replies: 25
- Views: 3337
Re: Crank counterweights
Erik, what does Magnaflux mean?
- Fri Sep 03, 2021 5:15 pm
- Forum: General Discussion Forum
- Topic: Crank counterweights
- Replies: 25
- Views: 3337
Re: Crank counterweights
Still confused on the diamond thing though
- Fri Sep 03, 2021 5:14 pm
- Forum: General Discussion Forum
- Topic: Crank counterweights
- Replies: 25
- Views: 3337
Re: Crank counterweights
My eingine is a November 26 as marked on blocks and car was around then too being a wooden wheeled.
- Fri Sep 03, 2021 4:00 pm
- Forum: General Discussion Forum
- Topic: Crank counterweights
- Replies: 25
- Views: 3337
Re: Crank counterweights
I have a 26 eingine, does that mean that they would not fit?
- Fri Sep 03, 2021 2:07 pm
- Forum: General Discussion Forum
- Topic: Crank counterweights
- Replies: 25
- Views: 3337
Re: Crank counterweights
What is the different crank years?
- Fri Sep 03, 2021 7:42 am
- Forum: General Discussion Forum
- Topic: Crank counterweights
- Replies: 25
- Views: 3337
Re: Crank counterweights
Alitle confused, why would it be bad on an original crankshaft?
- Wed Sep 01, 2021 9:25 am
- Forum: General Discussion Forum
- Topic: Some questions about a replacement radiator
- Replies: 32
- Views: 3734
Re: Some questions about a replacement radiator
Ok, the bottom pipe is almost always to hot to hold at around 150 or 170. It just empties itself within 10 miles of easyish driving in 80 degree weather
- Tue Aug 31, 2021 2:28 pm
- Forum: General Discussion Forum
- Topic: Crank counterweights
- Replies: 25
- Views: 3337
Crank counterweights
What do you all think about crankshaft counterweights?
Are they easier on your eingine by elemenating some vibration, or to they put too much weight on the shaft? I will be curious to see what you all think!
Are they easier on your eingine by elemenating some vibration, or to they put too much weight on the shaft? I will be curious to see what you all think!
- Tue Aug 31, 2021 7:17 am
- Forum: Classifieds - Parts
- Topic: SOLD FS Brake Pedals with accessory activation tangs welded on already
- Replies: 5
- Views: 2057
Re: FS Brake Pedals with accessory activation tangs welded on already
I will take the 27 pedal, email sent
- Mon Aug 30, 2021 6:43 pm
- Forum: General Discussion Forum
- Topic: One more radiator question
- Replies: 14
- Views: 2385
Re: One more radiator question
Ok, when I fill it to the top, it lowers until I can see the tubes in about 10 miles.
- Mon Aug 30, 2021 10:59 am
- Forum: General Discussion Forum
- Topic: One more radiator question
- Replies: 14
- Views: 2385
One more radiator question
If my radiator is clogged up, is that what causes an overflow? Does the lack of flow through the radiator make it to a builds up in the top tank and over flows through the overflow tube?
- Mon Aug 30, 2021 8:09 am
- Forum: General Discussion Forum
- Topic: Radiator problem found
- Replies: 26
- Views: 3989
Re: Radiator problem found
If it wont clear out, how much is a new radiator for a 26?
- Mon Aug 30, 2021 8:07 am
- Forum: General Discussion Forum
- Topic: Radiator problem found
- Replies: 26
- Views: 3989
Re: Radiator problem found
Ok, thanks
- Mon Aug 30, 2021 8:03 am
- Forum: Classifieds - Parts
- Topic: wtb motometer
- Replies: 3
- Views: 1159
Re: wtb motometer
Does any one have one sitting on a shelf mabey?
- Mon Aug 30, 2021 8:02 am
- Forum: Classifieds - Parts
- Topic: Great misc pile of goodies FOR SALE
- Replies: 15
- Views: 4989
Re: Great misc pile of goodies FOR SALE
Email sent
- Mon Aug 30, 2021 8:00 am
- Forum: General Discussion Forum
- Topic: Radiator problem found
- Replies: 26
- Views: 3989
Re: Radiator problem found
Thanks for the advice, I think I left out alittle pertanent info: it is a flat tube radiator, I have reverse flushed it with a very hi volume hose but it still wont clear. Does the bottom tank solder off?