Search found 190 matches

by noelchico
Mon Mar 11, 2024 7:40 pm
Forum: Classifieds - Parts
Topic: Ruckstell 3:25 Ring Gear, Bill Everett
Replies: 6
Views: 487

Re: Ruckstell 3:25 Ring Gear, Bill Everett

I believe, as Bob said, you would need the 12 tooth pinion and a recessed ring gear made for the 3:1 high speed gears. Then you would need to add space under the ring gear to raise it to the proper clearance with the 12 tooth pinion. When I did it, I had to add a 1/16 inch, or .0625 shim. Stacking s...
by noelchico
Thu Feb 29, 2024 10:52 pm
Forum: General Discussion Forum
Topic: 27 driving chassis, an I being cheap offering $1500?
Replies: 24
Views: 1067

Re: 27 driving chassis, an I being cheap offering $1500?

The cost of a few gallons of antifreeze cost the owner dearly. :(
by noelchico
Tue Feb 27, 2024 6:51 pm
Forum: General Discussion Forum
Topic: Rocky mtns and roughed up drums.
Replies: 19
Views: 1125

Re: Rocky mtns and roughed up drums.

Does he really need a lathe? How about jacking up a rear wheel with the brake drum on it, put the car in high gear, and hit it with some emery cloth? :D
by noelchico
Tue Feb 27, 2024 6:42 pm
Forum: General Discussion Forum
Topic: I'm going screwy looking for screws.
Replies: 18
Views: 886

Re: I'm going screwy looking for screws.

Robert, I see Menards.com has them in zinc coating. Manufactured by Midwest Fastener. Is this what you are looking for? https: //www.menards.com/main/hardware/fasteners-connectors/screws/wood-screws/midwest-fastener-reg-10-slotted-drive-zinc-flat-head-wood-screws/61284/p-1444439874195-c-8940.htm Noel
by noelchico
Sat Feb 24, 2024 9:24 pm
Forum: General Discussion Forum
Topic: LED headlight faint flicker.
Replies: 16
Views: 701

Re: LED headlight faint flicker.

I don't think it's a problem, as the car runs well. I only noticed it in the dark garage at night. I thought my lenses were vibrating and reflecting light until I looked closer. :D
by noelchico
Thu Feb 22, 2024 9:05 pm
Forum: General Discussion Forum
Topic: LED headlight faint flicker.
Replies: 16
Views: 701

LED headlight faint flicker.

Rather than tacking this onto the other LED thread, I just have a question. I noticed tonight with the 1920 roadster running in a dark garage that there is a very faint, barely perceptible flicker from my LED headlight bulbs with the light switch turned off. This seems to coincide with engine RPM. I...
by noelchico
Sun Feb 11, 2024 6:15 pm
Forum: Classifieds - Vehicles
Topic: WTB open dual axle trailer
Replies: 10
Views: 969

Re: WTB open dual axle trailer

don't forget that an enclosed trailer makes a fair garage in the off driving months. Mine keep out mice, weather, and free up other storage.
by noelchico
Thu Feb 08, 2024 3:45 pm
Forum: General Discussion Forum
Topic: What Have You Done to Your Model T in February?
Replies: 35
Views: 2674

Re: What Have You Done to Your Model T in February?

https://www.mtfca.com/phpBB3/download/f ... &id=182746
Went for a 5 mile drive during our early February thaw for nuts and fun. Side curtains make for difficult entry and exit for us "bigger" people! :lol:
by noelchico
Sat Feb 03, 2024 7:03 pm
Forum: General Discussion Forum
Topic: Chevy rod bolt for T????
Replies: 7
Views: 765

Re: Chevy rod bolt for T????

I will add that I replaced the rod bolts in my 23 after I burned one rod bearing and had it rebabbited and sized with timesaver. I adjusted it at 30 ft/lbs but had to take out an additional shim on using a Chevy rod bolt at 40 ft/lbs. There was still a fair shim pack under the cap. I had previously ...
by noelchico
Mon Jan 29, 2024 2:11 pm
Forum: General Discussion Forum
Topic: Just food for thought. Diesel fuel in gas tank?
Replies: 15
Views: 813

Re: Just food for thought. Diesel fuel in gas tank?

I've joined a number of folks by adding TCW-3 two-stroke oil to gas in my T's, as well as my moderns. It's designed to burn and is a top cylinder lube, decreasing piston ring friction and lubing the valve stems. Maybe it's just my imagination but I've found about 5% improved fuel economy in our RAV4...
by noelchico
Sun Jan 21, 2024 3:09 pm
Forum: General Discussion Forum
Topic: Wheel studs
Replies: 7
Views: 368

Re: Wheel studs

The left rear studs were not peaned over on my 20 roadster with Pasco wheels and I didn’t check them. The wheel left us and travelled nearly a quarter mile across a field at a national tour. I thank God we found it! Lesson learned. Don’t trust prior owners workmanship!
by noelchico
Fri Jan 19, 2024 3:37 pm
Forum: General Discussion Forum
Topic: Pan Straightening Jig for sale on Facebook Marketplace in Ohio
Replies: 17
Views: 1030

Re: Pan Straightening Jig for sale on Facebook Marketplace in Ohio

I'm glad it went to a T guy so it is used correctly and remains in circulation . :)
by noelchico
Tue Jan 16, 2024 10:42 am
Forum: General Discussion Forum
Topic: Nice night for a drive
Replies: 11
Views: 851

Re: Nice night for a drive

I've got a horse hide quilt with the hair on one side that makes a dandy period correct lap blanket for similar forays. Stay warm. Have fun! :)
by noelchico
Fri Jan 12, 2024 3:24 pm
Forum: General Discussion Forum
Topic: Advice needed for touring rear window.
Replies: 10
Views: 421

Re: Advice needed for touring rear window.

How about find a friend, spouse, neighbor kid to push the needle and thread back inside with each stitch. It might take less time than coming up with another fix. :D
by noelchico
Wed Jan 10, 2024 11:22 pm
Forum: General Discussion Forum
Topic: Wanted: Ideas for side curtians for 1922 2 man top
Replies: 14
Views: 562

Re: Wanted: Ideas for side curtians for 1922 2 man top

Austin, We've made side curtains for our 23 touring as well as our 20 roadster. We took some heavy paper and made a pattern for each side, going back behind the rear side portions of the rear top segment. We purchased some plastic/vinyl sheet from the local WalMart and cut it big. We fitted it, trim...
by noelchico
Wed Dec 20, 2023 11:01 pm
Forum: General Discussion Forum
Topic: A picture is worth 1,000 words with Steve Jelf
Replies: 58
Views: 3726

Re: A picture is worth 1,000 words with Steve Jelf

Great to see you up and about, Steve. Have a Merry and Blessed Christmas.
by noelchico
Tue Dec 19, 2023 7:00 pm
Forum: General Discussion Forum
Topic: Filling old tack rail holes.
Replies: 14
Views: 751

Re: Filling old tack rail holes.

Hey, I just taught my 12-year-old granddaughter a new word. :D
by noelchico
Thu Nov 30, 2023 7:57 pm
Forum: General Discussion Forum
Topic: Look who I found -Steve Jelf
Replies: 22
Views: 2227

Re: Look who I found -Steve Jelf

Steve, it is VERY good to see you. Praying for your rapid and complete recovery.
by noelchico
Sun Nov 26, 2023 3:27 pm
Forum: OT - Off topic
Topic: A Wake Up Call on How Times Are Changing....,
Replies: 77
Views: 4503

Re: A Wake Up Call on How Times Are Changing....,

Nobody forces anybody to read every thread on the forum. If you don’t like the contents of a thread, don’t read it. I enjoy the discourse, even though I don’t agree with all of it.
by noelchico
Mon Nov 20, 2023 10:31 pm
Forum: General Discussion Forum
Topic: Steve Jelf Sunday, 11/19
Replies: 32
Views: 3107

Re: Steve Jelf Sunday, 11/19

Glad to hear further encouraging notes on Steve's recovery. I'm following and praying for his recovery. He's a remarkable gentleman!
by noelchico
Sat Oct 14, 2023 10:49 pm
Forum: Classifieds - Parts
Topic: For Sale: 1926-27 Wire Wheel Lug Nuts
Replies: 2
Views: 361

Re: For Sale: 1926-27 Wire Wheel Lug Nuts

I’m putting wires on my 26 Coupe so I’ll take them if available. Noel Chicoine.
by noelchico
Fri Oct 13, 2023 11:04 pm
Forum: Classifieds - Parts
Topic: For Sale 23-25 touring body
Replies: 9
Views: 871

Re: For Sale 23-25 touring body

Very pretty. I’m looking but unfortunately need an early 23 body low hood to replace mine vs a rewooding and rebuild. Good luck with the sale.
by noelchico
Fri Sep 22, 2023 8:36 pm
Forum: General Discussion Forum
Topic: Floating transmission shafts
Replies: 19
Views: 1062

Floating transmission shafts

I'm looking at some old posts I missed and saw the one on "23 tranny on 26 block". Is there any chance Les or somebody would consider doing another run of the floating transmission shafts. I have 2 and would like a third and maybe a fourth. I'm sold on the concept and believe they may be the best wa...
by noelchico
Fri Sep 22, 2023 8:35 pm
Forum: Classifieds - Parts
Topic: Floating transmission shafts
Replies: 1
Views: 223

Floating transmission shafts

I'm looking at some old posts I missed and saw the one on "23 tranny on 26 block". Is there any chance Les or somebody would consider doing another run of the floating transmission shafts. I have 2 and would like a third and maybe a fourth. I'm sold on the concept and believe they may be the best wa...
by noelchico
Fri Jul 28, 2023 4:38 pm
Forum: Classifieds - Parts
Topic: NEW 12 tooth pinion thank you Chaffin’s
Replies: 9
Views: 1059

Re: NEW 12 tooth pinion thank you Chaffin’s

You may need to shim a Ruckstell or recessed ring gear as I don't believe any were made to accept a 12 tooth that is smaller diameter than a 13 and bigger than an 11 tooth. I made a large ring gear shim from a 1/16 sheet of aluminum to get my ring-pinion clearance. Stacking 4-5 thinner shims may be ...
by noelchico
Sun Jul 02, 2023 11:28 pm
Forum: General Discussion Forum
Topic: Pulling a Model T
Replies: 41
Views: 2758

Re: Pulling a Model T

Would adding 4-6 quarts of oil supply enough lubrication to the transmission to safely tow it at a slow speed in neutral? Drain the oil when you get it home.
by noelchico
Mon Jun 26, 2023 8:15 pm
Forum: General Discussion Forum
Topic: Special factory oval fuel tank spacer brackets, circa 1920 images.
Replies: 6
Views: 829

Re: Special factory oval fuel tank spacer brackets, circa 1920 images.

Dennis, I decided to take a look at my mid-August 1919 1920 model Roadster to answer your question. I had never looked under the hinged sheet metal lid over the tank since buying the car about 7 years ago. It has a round tank and had a tool kit with Ford pliers, tire iron, several wrenches, and a Wa...
by noelchico
Sun Jun 25, 2023 11:13 pm
Forum: General Discussion Forum
Topic: Rod cap, run it loose or make a shim?
Replies: 17
Views: 1344

Re: Rod cap, run it loose or make a shim?

I just replaced a single rod in my engine. FWIW the replacement re-babbited rod made to fit my crankshaft was NOT the same shape or weight as the one I removed. I was concerned about balance and ended up returning the new rod and had my original rod re-babbited and bored to fit my crank. Then I used...
by noelchico
Thu Jun 15, 2023 7:26 pm
Forum: General Discussion Forum
Topic: Beach Party
Replies: 12
Views: 929

Re: Beach Party

The driver of the roadster pickup in picture 12 needs to climb past the roll of barbed wire, since the drivers door was non-functional. :)
by noelchico
Thu Jun 15, 2023 7:22 pm
Forum: General Discussion Forum
Topic: Head gasket?
Replies: 30
Views: 1884

Re: Head gasket?

So far the car starts easily and runs strong. I drove around town for several errands today. I changed the oil which looked a little "funny". I'll bring a head gasket and metalic paint or copper coat and hope for the best. Teresa and I are looking forward to Manhattan, Kansas.
by noelchico
Thu Jun 15, 2023 12:34 pm
Forum: General Discussion Forum
Topic: Head gasket?
Replies: 30
Views: 1884

Re: Head gasket?

I now have a few spare head gaskets, I'll carry one and a torque wrench.
by noelchico
Thu Jun 15, 2023 11:37 am
Forum: General Discussion Forum
Topic: Head gasket?
Replies: 30
Views: 1884

Re: Head gasket?

!!! :D Filled it with water after putting in a new Welch plug. I used a buffalo nickel as there weren't any correct sized plugs in town. I let the Ultra Black set up for 24 hours before filling the radiator. Started the engine and immediately had bubbling and water pushing to 6 inches above the radi...
by noelchico
Wed Jun 14, 2023 10:15 am
Forum: General Discussion Forum
Topic: Head gasket?
Replies: 30
Views: 1884

Re: Head gasket?

I ran the engine for about 10 seconds with no welch plug this morning. I felt no pulses putting my finger over the hole so there is likely no pressure leak from a cylinder. Thanks.
by noelchico
Wed Jun 14, 2023 10:06 am
Forum: General Discussion Forum
Topic: Head gasket?
Replies: 30
Views: 1884

Re: Head gasket?

I'll get a real welch plug this morning. I believe it's 13/16 but don't see it sized with the vendors. Thanks for the inputs. So far it kept me from pulling the head.
by noelchico
Tue Jun 13, 2023 9:19 pm
Forum: General Discussion Forum
Topic: Head gasket?
Replies: 30
Views: 1884

Re: Head gasket?

Scott, that's my main reason for asking the experts. I am assuming, likely wrongly, that compression or firing impulses are leaking into the water jacket causing the plug to blow. As an aside, I just put in a concave buffalo nickel with Ultra-black tonight and it blew out on starting.
by noelchico
Tue Jun 13, 2023 8:13 pm
Forum: General Discussion Forum
Topic: Head gasket?
Replies: 30
Views: 1884

Head gasket?

I took the 23 touring out to check it out before next week's Manhattan, Ks tour. After 15 miles and a long uphill pull it started to smell a little warm so I slowed down. I'd put a straight radiator cap on instead of my usual moto meter. After a few miles it was smelling hot so I pulled into our chu...
by noelchico
Fri Apr 14, 2023 12:55 pm
Forum: General Discussion Forum
Topic: Engine knock
Replies: 21
Views: 1568

Re: Engine knock

I've spoken to Harvey several times regarding this engine and car, and hope to finally meet him on tour this summer. He mentioned to me that the crank was removed for the cylinder boring, but he didn't believe new babbit was poured or bored as the original crankshaft was put back in. I expressed con...
by noelchico
Tue Apr 04, 2023 6:37 pm
Forum: General Discussion Forum
Topic: what year is it? No i'm not Rip Van Winkle
Replies: 16
Views: 1500

Re: what year is it? No i'm not Rip Van Winkle

I'm sure many of us own a car made in the fall of the year prior to its official model year. I own a Roadster titled as a 1920 car but manufactured in the fall of 1919. I'm putting 1919 YOM plates on it
by noelchico
Tue Apr 04, 2023 6:24 pm
Forum: General Discussion Forum
Topic: what year is it? No i'm not Rip Van Winkle
Replies: 16
Views: 1500

Re: what year is it? No i'm not Rip Van Winkle

I'm sure many of us own a car made in the fall of the year prior to its official model year. I own a Roadster titled as a 1920 car but manufactured in the fall of 1919. I'm putting 1919 YOM plates on it
by noelchico
Wed Mar 29, 2023 2:07 pm
Forum: General Discussion Forum
Topic: Grease hemorrhage
Replies: 10
Views: 1003

Re: Grease hemorrhage

John, If the oil hole is on the bottom, will it allow a lot more oil to flow through the 4th main going up hills? I understand from a discussion with Gene French that many 4th mains have no hole.
by noelchico
Tue Mar 14, 2023 6:03 pm
Forum: Classifieds - Parts
Topic: Pasco Wire Wheels and Hubs
Replies: 3
Views: 957

Re: Pasco Wire Wheels and Hubs

For what it's worth, spokes are available at Buchanon Spoke and Rim, Inc.
by noelchico
Tue Mar 14, 2023 1:43 pm
Forum: General Discussion Forum
Topic: Air Filter
Replies: 29
Views: 2064

Re: Air Filter

There have been dynamometers at 2 tours I have been on. I'd like to run my car on a dynamo both with and without a filter and see the difference. Since engine rebuilds are spendy, and I drive on occasional gravel roads, I run one. I haven't tried to see the effect on top speed, because after breakin...
by noelchico
Sat Mar 04, 2023 5:51 pm
Forum: General Discussion Forum
Topic: Sudden Erratic Steering that could have been catastrophic!
Replies: 18
Views: 1774

Re: Sudden Erratic Steering that could have been catastrophic!

Thank you, Brent. I have a 26 coupe I have driven little since acquiring it 15 years ago. I just rebuilt the differential and adjusted the engine. I remember many years ago I made a right turn and it seemed to suddenly oversteer. I have been careful since, but cautious. This gives me something to ch...
by noelchico
Wed Feb 22, 2023 9:55 pm
Forum: OT - Off topic
Topic: 6.7 Ford PS upgrade Heads Up
Replies: 7
Views: 989

Re: 6.7 Ford PS upgrade Heads Up

Another reason I have a 6.2 gas F250. Diesel engines cost a lot more to buy and it seems to maintain. I can buy a lot of gasoline for the difference.
by noelchico
Wed Feb 22, 2023 9:42 pm
Forum: General Discussion Forum
Topic: Horn will not fit inside 1926 Coupe hood after installing a water pump
Replies: 57
Views: 3513

Re: Horn will not fit inside 1926 Coupe hood after installing a water pump

I'm betting that Scott could walk around his unincorporated home-town with $2000 in his pocket a lot safer than someone in California could with $200 in their pocket. It's likely all his neighbors within 10 miles know each other, their hobbies, recognize their cars, and watch his home when he's not ...
by noelchico
Sat Feb 18, 2023 7:02 pm
Forum: General Discussion Forum
Topic: Stromberg LF float needle
Replies: 5
Views: 757

Re: Stromberg LF float needle

I am waiting on this answer also, as I have a very nice OF that I acquired that has a leaking needle. I think everything else is clean. Noel
by noelchico
Wed Feb 15, 2023 2:40 pm
Forum: General Discussion Forum
Topic: Triple Gear Bushings
Replies: 14
Views: 1334

Re: Triple Gear Bushings

Per Dan's recommendations and with his instruction I ball sized my triple-gear bushings prior to placement on the pins. So far after 1 tour, they seem fine. I believe this procedure work hardens the inner bushing surface as well as forces the bushing to fit tighter into the gear. It is also easy to ...
by noelchico
Mon Feb 13, 2023 7:55 pm
Forum: Classifieds - Parts
Topic: Set of Five Schrader 777 Stems on Ebay (not mine)
Replies: 6
Views: 984

Re: Set of Five Schrader 777 Stems on Ebay (not mine)

What valve stems were used on aftermarket rims like Pasco, Dayton, and others?
by noelchico
Sat Feb 11, 2023 11:38 pm
Forum: General Discussion Forum
Topic: Rod bolts, run original or buy new?
Replies: 14
Views: 1479

Re: Rod bolts, run original or buy new?

I second the suggestion of Bob Shirley regarding using small block Chevy rod bolts. They have a knurled shaft that must be ground down a bit to slide into a model T rod but that is easy with a file and a drill press. The heads have a flat side that fits the T rod well. BUT they don't weigh the same....
by noelchico
Thu Feb 02, 2023 8:05 pm
Forum: General Discussion Forum
Topic: Installing Pistons
Replies: 8
Views: 1076

Re: Installing Pistons

William, FYI, if your connecting rod bolts are questionable after dozens of removals in the past 100 years, they may be replaced with small block Chevy rod bolts. The knurling needs to be filed or ground down but that's easy in a drill press or lathe. Make sure you replace all of them as they weigh ...
by noelchico
Thu Feb 02, 2023 7:47 pm
Forum: General Discussion Forum
Topic: Is it worth the drive?
Replies: 10
Views: 1390

Re: Is it worth the drive?

If you don't want them, perhaps contact a closer T club to see if someone would like to save these parts.
by noelchico
Sun Jan 29, 2023 11:30 pm
Forum: OT - Off topic
Topic: very off topic: 2 dollar bills bad luck?
Replies: 29
Views: 2788

Re: very off topic: 2 dollar bills bad luck?

They circulate around our town with some frequency. they are used at the horse races for $2 bets. I get them before trips and use them for tips.
by noelchico
Mon Jan 09, 2023 7:47 pm
Forum: General Discussion Forum
Topic: Improving Speed on an Improved Car (26,27)
Replies: 34
Views: 2596

Re: Improving Speed on an Improved Car (26,27)

Several years ago, I had my 23 touring at 58mph while passing an Amtrac train on my way back from East Glacier Park to the tour headquarters in Whitefish, Mt. I have a Z head, .280 cam, high volume intake, Chaffins dual exhaust manifold, and Stromberg OF carb. Also, Rocky Mountain brakes. I'd replac...
by noelchico
Sun Jan 08, 2023 1:37 pm
Forum: General Discussion Forum
Topic: Rear axle crack
Replies: 29
Views: 2630

Re: Rear axle crack

I had an axle break at the same place on last year's Ohio tour. Fortunately, we were attempting to pull from a stop sign, not cruising at 35-40 mph. I'd replaced these axles 15 years ago and noted grooves from the Hyatte bearings at the break and on the other axle as well. I believe there were issue...
by noelchico
Sun Jan 01, 2023 1:15 pm
Forum: General Discussion Forum
Topic: "Model Ts Run On Any Kind of Fuel". ...So, what about Flex Fuel?
Replies: 9
Views: 1168

Re: "Model Ts Run On Any Kind of Fuel". ...So, what about Flex Fuel?

I've checked fuel economy in 3 vehicles with E-10. Each gives about 10% less fuel economy as regular gasoline. I'd get the same mileage as if I drove the car with pure gasoline and poured the ethanol onto the pavement. Unfortunately, the E-10 costs over 10% less than pure gasoline due to subsidies s...
by noelchico
Tue Dec 27, 2022 11:29 pm
Forum: General Discussion Forum
Topic: Look what Santa got me for Christmas.
Replies: 10
Views: 2261

Re: Look what Santa got me for Christmas.

Sean, I'd be happy to take them off your hands to put on my "Dr's Coupe". :lol: If you ever get to the capital, look me up.
by noelchico
Fri Dec 16, 2022 5:49 pm
Forum: Classifieds - Vehicles
Topic: 1927 Model T Dr’s Coupe. No longer on market
Replies: 16
Views: 7305

Re: 1927 Model T Dr’s Coupe

Are you keeping it? That's a beautiful car!
by noelchico
Thu Dec 08, 2022 2:05 pm
Forum: General Discussion Forum
Topic: How to do a roadster top wrong
Replies: 20
Views: 2120

Re: How to do a roadster top wrong

George, I agree. That top generates a good belly laugh. My 20 roadster was purchased after the prior owner ran into a too-low garage door. Friends helped him replace the top and the front irons didn't come low enough for the front lip to close the gap over the windshield. I talked to Mark at Classti...
by noelchico
Thu Dec 08, 2022 1:50 pm
Forum: Classifieds - Vehicles
Topic: Wanted to Buy, 1917 Coupelet or 1918 Coupe ONLY!!!
Replies: 125
Views: 33212

Re: Wanted to Buy, 1917 Coupelet or 1918 Coupe ONLY!!!

I don't see how Walt's been ungrateful or rude. He is just very specific about what he wants and won't settle for anything that is not that. He may need to wait a long time, but I suspect he will eventually get the car he desires. Good luck, Walt.
by noelchico
Mon Nov 21, 2022 10:04 am
Forum: General Discussion Forum
Topic: Before I reinvent the wheel.....any creative suggestions?
Replies: 8
Views: 1242

Re: Before I reinvent the wheel.....any creative suggestions?

Antonie, those need to be slot headed screws to be authentic. :lol:
by noelchico
Sat Nov 19, 2022 8:28 pm
Forum: General Discussion Forum
Topic: CHAFFIN'S GARAGE IS MOVING
Replies: 17
Views: 2761

Re: CHAFFIN'S GARAGE IS MOVING

I called and talked to Dave Friday afternoon before the move. He said he'd get it out either that afternoon or Saturday morning. It arrived Tuesday. I bet I got the last shipment before the move. Best of wishes on your new location. It's always a pleasure to do business with Chaffin's.
by noelchico
Sat Nov 19, 2022 8:16 pm
Forum: Classifieds - Parts
Topic: wanted - 1925 engine block or complete engine
Replies: 10
Views: 1265

Re: wanted - 1925 engine block or complete engine

Scott, let me check my stash of engines at my shed. I'll need to check the SN's. I'm not that far east of you. MAYBE there's a 25 in the group.
by noelchico
Thu Nov 17, 2022 10:45 pm
Forum: General Discussion Forum
Topic: inner rear axle bearings
Replies: 16
Views: 1713

Re: inner rear axle bearings

I was able to find another Hyatt in my stash today that is .497-.498. one end is .001 smaller. I'll use it and try to de-rust the other Hyatt for possible future use. I hate throwing away the more worn one, so will keep it and consider shim stock behind the race if I use it. The solid one.....who kn...
by noelchico
Thu Nov 17, 2022 10:37 pm
Forum: General Discussion Forum
Topic: Water… pumping…?
Replies: 46
Views: 4131

Re: Water… pumping…?

Beautiful work, as usual, Kevin. With the HP you are going after, you likely need that water pump.
by noelchico
Wed Nov 16, 2022 3:10 pm
Forum: General Discussion Forum
Topic: inner rear axle bearings
Replies: 16
Views: 1713

inner rear axle bearings

I'm replacing a broken right axle in my Ruxtell with new axles. I found the right outer sleeve was cracked, and the housing had a cracked/grooved portion at the far outer edge that either occurred at the time of the break or preceded it. Both axles were replaced 15+ years ago and the broken one had ...
by noelchico
Thu Nov 03, 2022 5:44 pm
Forum: General Discussion Forum
Topic: replacing a connecting rod.
Replies: 20
Views: 1796

Re: replacing a connecting rod.

In follow up, I was able to remove the #3 rod through the inspection port fairly easily. I put a bolt through the wrist pin and rotated the piston so that the bolt contacted the block to avoid twisting the rod, and removed the wrist pin bolt. I slid the wrist pin partially out with a long L shaped a...
by noelchico
Thu Nov 03, 2022 5:31 pm
Forum: General Discussion Forum
Topic: Question about rods
Replies: 9
Views: 1070

Re: Question about rods

Interesting discussion. I'm in the middle of replacing a rod I wrecked in my 23. I ordered a re-babbited rod bored to my crankshaft and just got it today. It's an aftermarket "light" rod but weighs 569 grams compared to my Ford script rod at 486 grams (without bolts or nuts). After discussion with m...
by noelchico
Sat Oct 29, 2022 10:43 am
Forum: General Discussion Forum
Topic: replacing a connecting rod.
Replies: 20
Views: 1796

Re: replacing a connecting rod.

Thank you, gentlemen, for your comments. I may try to pull the rod through the bottom. If it doesn't work, I'll pull the head. The crank looks pristine, measuring 1.235, so it must have had a regrind when overhauled 15 years ago. Since all the other rods look good, I assumed the problem was my not p...
by noelchico
Fri Oct 28, 2022 7:16 pm
Forum: General Discussion Forum
Topic: replacing a connecting rod.
Replies: 20
Views: 1796

replacing a connecting rod.

I got careless (stupid) when adjusting my rods, putting oil in the caps but neglecting to fill the rod dips before starting. At about 30 seconds a loud knocking occurred. Pulling the inspection pan revealed #3 rod was loose and had damaged babbit. The journal looks pristine, and the other rods are t...
by noelchico
Sat Aug 20, 2022 4:05 pm
Forum: General Discussion Forum
Topic: Ruckstell ring/pinion clearance.
Replies: 8
Views: 1038

Re: Ruckstell ring/pinion clearance.

The only place I believe I could place a .065 shim is to make one to fit between the notch plate and inner differential housing, but then my shifter fork MAY not move the sliding clutch gear enough for a positive shift. Other spots appear to affect the sliding gear mesh with the notch plate and thru...
by noelchico
Fri Aug 19, 2022 6:13 pm
Forum: General Discussion Forum
Topic: Ruckstell ring/pinion clearance.
Replies: 8
Views: 1038

Re: Ruckstell ring/pinion clearance.

I very much appreciate the above comments. The ring gear and pinion align well, and the system turns easily. I just trial fitted both a .015 and a .010 shim (0.025 total) and now have .048 so it appears the lateral movement relates directly to the shim thickness. I am hesitant to stack four 0.015 sh...
by noelchico
Fri Aug 19, 2022 3:47 pm
Forum: General Discussion Forum
Topic: Ruckstell ring/pinion clearance.
Replies: 8
Views: 1038

Ruckstell ring/pinion clearance.

I admit I'm a shade tree mechanic (with no air conditioning in my garage). I'm replacing the standard ring gear with no relief on the back with a 39 tooth gear with a relief and a 12 tooth pinion to get a 3.25:1 gear ratio. The previous owner had neglected to replace the right side inner Hiatt beari...
by noelchico
Tue Aug 09, 2022 10:23 pm
Forum: General Discussion Forum
Topic: Bye!!!!!
Replies: 30
Views: 4576

Re: Bye!!!!!

Hank, We've never met but I also have enjoyed your knowledge and wit. I do hope to meet you someday.
by noelchico
Thu Jul 28, 2022 3:06 pm
Forum: General Discussion Forum
Topic: Floorboards
Replies: 1
Views: 803

Re: Floorboards

Dennis, we're headed for our cabin in the Black Hills this afternoon. Custer is a great place. You can make floorboards from a 2 ft by 4 ft 5/8" plywood chunk. I just made some to put a 26 engine in my 23 last week. Bevel the edges at 30 degrees where the 2 pieces meet and they stay down better and ...
by noelchico
Wed Jul 06, 2022 7:42 pm
Forum: General Discussion Forum
Topic: Stan Howe service manual for stromberg OF
Replies: 3
Views: 1043

Re: Stan Howe service manual for stromberg OF

Pat, I have a copy of the late Stan Howes Stromberg book. It's 28 type or picture containing pages with some of Stan's comments on installation and adjustment. We're getting ready to get the grandkids to take to the Hamilton, Ohio tour so I don't have time to copy it at present. If you're going to t...
by noelchico
Mon Jul 04, 2022 8:57 pm
Forum: General Discussion Forum
Topic: Looking For Drive Pins For Pasco 60 Spoke Wire Wheels
Replies: 5
Views: 1036

Re: Looking For Drive Pins For Pasco 60 Spoke Wire Wheels

John, I lost a wheel and hub last year on the Spokane tour because I didn't check and the prier owner hadn't peened the nuts on the inside of the left rear brake hub. (across a field and lay down in the weeds 1/4 mile away.) I made the replacements using grade 5 bolts of the correct length, tapped a...
by noelchico
Tue Jun 28, 2022 9:41 pm
Forum: General Discussion Forum
Topic: Rough acceleration and coughing back through the carb
Replies: 29
Views: 2911

Re: Rough acceleration and coughing back through the carb

Make sure that when you replaced the timer wires that they didn't get crossed. I've seen experienced T mechanics make that mistake. The firing order is 1-2-4-3. Slowly turn the engine over with the battery on and check what plugs fire.
by noelchico
Wed Jun 15, 2022 7:11 pm
Forum: General Discussion Forum
Topic: Wonderful Wisconsin Tour
Replies: 28
Views: 5253

Re: Wonderful Wisconsin Tour

Jeff, if you have time stop at the host motel and you can likely pick up a ride for the day. I've got a rider for Monday and my wife will join me in our roadster on Tuesday so I can't give you a ride but I'm sure you could hitchhike along for a day or two.
by noelchico
Mon Jun 06, 2022 10:11 pm
Forum: General Discussion Forum
Topic: Planting Model T seeds
Replies: 9
Views: 1470

Re: Planting Model T seeds

Scott. I've a daughter in Billings. Perhaps I could throw an old engine in the rig the next time we go to visit. ;)
by noelchico
Tue May 31, 2022 2:00 pm
Forum: General Discussion Forum
Topic: Cartouche Upholstery
Replies: 34
Views: 4130

Re: Cartouche Upholstery

I, for one, am happy with Clastique. I am happy we have Cartouche and all the other manufacturers who continue to support this hobby. I sure couldn't make what they are providing for the cost and research and acquisition of the materials that they do. I suspect that it may be difficult, if not impos...
by noelchico
Tue May 31, 2022 1:52 pm
Forum: General Discussion Forum
Topic: Camshaft lift question.
Replies: 2
Views: 758

Re: Camshaft lift question.

thank you, John
by noelchico
Tue May 31, 2022 11:21 am
Forum: General Discussion Forum
Topic: Camshaft lift question.
Replies: 2
Views: 758

Camshaft lift question.

If I have a .250 lift camshaft, does it lift the valves .250 or do you subtract the 10-12 thousandths of lifter clearance and you only get .238-.240 lift?
by noelchico
Mon May 30, 2022 11:26 pm
Forum: General Discussion Forum
Topic: From Coast to Coast
Replies: 170
Views: 16416

Re: From Coast to Coast

By all means, please keep us apprised of your route. On your way to Mt. Rushmore you will either come through Pierre, SD ( my current location) on Hwy 34 or take the more southern route through northern Nebraska. Either route as you leave easter South Dakota or Nebraska you may go 50 miles between t...
by noelchico
Sun May 29, 2022 9:22 pm
Forum: General Discussion Forum
Topic: What have you done on your Model T in May?
Replies: 55
Views: 5871

Re: What have you done on your Model T in May?

Sorry, no pics so I must not have done it. First I replaced 3 outer spokes on one of my Pasco wheels. When I lost a wheel at last year's Spokane tour, the left Bennet brake band was ground 3/4 thru by contact with the pavement. I removed the band and a local welder welded in a patch piece that is ne...
by noelchico
Thu May 19, 2022 10:32 pm
Forum: General Discussion Forum
Topic: Height Question
Replies: 3
Views: 875

Re: Height Question

Just checked. My '23 Touring with '26 wire wheels hits 70.5 inches to the top of the windshield posts. My '20 Roadster with the folding windshield is 67 inches top down, windshield folded. You should be fine
by noelchico
Wed May 11, 2022 2:05 pm
Forum: General Discussion Forum
Topic: Accessory dual exhaust questions...
Replies: 10
Views: 1549

Re: Accessory dual exhaust questions...

I think I lost a little low end torque with the high volume intake but the biggest loss was with the exhaust change. However, once I get a few RPM, I walk up hills I used to downshift for and can pass other T's struggling up long grades. However, now that we have a few tours under our belt, we're mo...
by noelchico
Wed May 11, 2022 11:54 am
Forum: General Discussion Forum
Topic: Accessory dual exhaust questions...
Replies: 10
Views: 1549

Re: Accessory dual exhaust questions...

I have one of these manifolds on my '23 touring. I had a local muffler shop fabricate a 2:1 reduction to a larger pipe and muffler. I also have a Stromberg OF, .280 cam, high volume intake, and Z head on the car. I lost low end torque but also have a Ruckstall. I topped it out on a Montana tour at 5...
by noelchico
Wed Apr 27, 2022 4:08 pm
Forum: General Discussion Forum
Topic: Wonderful Wisconsin MTFCA Tour Update
Replies: 8
Views: 1430

Re: Wonderful Wisconsin MTFCA Tour Update

Allen, it's just a short hop across the pond. :lol: We'll keep Keith and Carol busy in your absence.
by noelchico
Sun Apr 17, 2022 8:18 pm
Forum: General Discussion Forum
Topic: Upper half of windshield on Touring "out of control" - meanwhile solution found.
Replies: 12
Views: 1768

Re: Upper half of windshield on Touring "out of control" - meanwhile solution found.

You could contact Mike at Classtique Auto Upholstery. He made a single panel for me in the past for my roadster. Much cheaper and easier than a whole new top.
by noelchico
Fri Apr 15, 2022 1:42 pm
Forum: General Discussion Forum
Topic: MTFCI tour Hamilton, Ohio
Replies: 3
Views: 910

Re: MTFCI tour Hamilton, Ohio

We're signed up and have hotel rooms reserved but hope to camp instead with our toy hauler. We are considering "dry camping" and perhaps mid-week emptying the black and grey tanks and refilling the water. There is a campground about 10 miles away that charges a small amount for this. Looking forward...
by noelchico
Wed Apr 13, 2022 11:42 am
Forum: General Discussion Forum
Topic: What Have You Done to Your Model T in April?
Replies: 69
Views: 7966

Re: What Have You Done to Your Model T in April?

Due to a loose lower crank pulley, I removed the radiator and fan on my '20 roadster. The cotter had broken holding the pulley pin and the pulley was loose. Since I had a leak from the front anyway, I cleaned the block face with diesel fuel followed by brake cleaner and made a "belt and suspenders" ...
by noelchico
Sat Mar 26, 2022 12:46 pm
Forum: General Discussion Forum
Topic: National tour Hamilton, Ohio
Replies: 11
Views: 2266

Re: National tour Hamilton, Ohio

I'm looking and don't see any nearby camping. We'd prefer to bring our toy hauler with the T inside and stay in a campground if there is one close. I don't desire to drive 10 miles or more to and from the activities in city traffic if possible.
by noelchico
Fri Mar 11, 2022 10:22 am
Forum: Classifieds - Parts
Topic: Pasco wire wheels
Replies: 10
Views: 2101

Re: Pasco wire wheels

Yea! Another set of Pascos on the road!
by noelchico
Tue Mar 01, 2022 8:19 pm
Forum: Classifieds - Parts
Topic: Stromberg LF Carb parts
Replies: 1
Views: 737

Re: Stromberg LF Carb parts

Tom, Is this parts carb still available?
by noelchico
Mon Feb 21, 2022 4:33 pm
Forum: General Discussion Forum
Topic: Does anyone know what these are?
Replies: 13
Views: 2356

Re: Does anyone know what these are?

If a Model T doesn't rattle, is it still a Model T? :lol:
by noelchico
Mon Feb 14, 2022 6:34 pm
Forum: Classifieds - Parts
Topic: PASCO wire wheel hubs SOLD
Replies: 1
Views: 824

Re: PASCO wire wheel hubs F/S

Message sent
by noelchico
Fri Feb 11, 2022 7:10 pm
Forum: General Discussion Forum
Topic: Mouse trap
Replies: 8
Views: 2056

Re: Mouse trap

Growing up on the farm, we several times lifted a rat-infested feeder up with a tractor loader and killed the rats that poured out. The cats took one each and disappeared. The dogs would grab one by the head, shake it to break its neck, toss it, and go after another. I use the bucket with a can on a...
by noelchico
Mon Jan 31, 2022 2:21 pm
Forum: General Discussion Forum
Topic: Overhead installation
Replies: 13
Views: 2392

Re: Overhead installation

I'm contemplating installing a RAJO C-35 in my '26 coupe. I suspect I'll need to modify the firewall but wonder if I can "easily" run my coilbox and coils.
by noelchico
Mon Jan 10, 2022 10:49 pm
Forum: Classifieds - Parts
Topic: Bennett brake pedal fs. Sold
Replies: 7
Views: 1604

Re: Bennett brake pedal fs

I'll take it, Mike.