MTFCA Forum

A nice, unrestored pair of headlamps that would date to about 1908-1912. The approximate measurements are 9 1/4 in diameter and height and 8 in depth and 7 1/2 inches between the fork mounting holes. There is no name on these so they can be used on any car. One has a broken reflector and the other one is missing a plain lens. There are a couple of...

For sale excellent unrestored, original throughout. Complete and runs excellent. It was in storage for close to 80 years. Never any rust out or dents. Original interior including front floor mat. One of the finest unrestored model T's in existence. The price is $23,500 FIRM, FIRM. NO TEXTING. five0745eight677eight. S. Mn.

This large Rubes 3/4 twist horn is about 10 tall and is about 6 wide. This is the style with the large bell and rim. It can be used on a right or left-hand early automobile. The original tubing is about 40 long. It's in great condition. Complete with the thumb nuts, screen, adapters, reed, etc. Honks well. The rubber bulb is obviously squished....

I have 4 headlamp sockets for 1915 or 1916 Model T’s. These differ from the later ones in that the pins are 90 degrees off. This was done to align the filament horizontally to allow the headlamp to be focused. Note the later socket in the middle of the picture. The focus screw for the 1915/16 is at the top of the light bulb, not to the side of the...

My 27 touring has a crack / bend in the the lower section of the the front bow. Wondering is I should attempt to repair on the car?
I have a lathe so I could cut it off at the break and make a dowel to fit inside, then braze up the joint.
Anybody tried this repair?

Cab anyone with a hempy cooper line boring set up take some measurements and pictures of the cutters for me mine are missing

For Sale Dodge Bros. spare tire carrier with four lug nuts. 3-7/8 inches between studs. Will need re-drilling for speedster. Price $275 plus shipping. Email, call, or text (248) 894-75fiveone. Thanks, Walt

Doing a full rebuild on my 22 centerdoor engine. Everything shows minimal wear so i ordered standard adjustable lifters. The problem is they wont go into the block. They seem to be one or two thousandths too big. Suggestions? Is there a reamer out there that would work for this?

For Sale: a 1914 original manual.

$112 a dollar per year since printed plus USPS mail.

For Sale is a nice 1910 - 1913 2 piece driveshaft housing, no bump spool, ball and collar. $600.00 plus shipping Lang’s 1-800-872-7871

For Sale is a rare accessory anti theft device. It is connected to the ignition system and will ground out when the car travels over uneven ground. There isn’t any manufacturer marking on the unit. $30.00 plus shipping. Lang’s 1-800-872-7871

For Sale is a reproduction Lucas Engineering Aermore Exhaust Whistle. $185.00 plus shipping. Lang’s 1-800-872-7871.

For Sale is an older “New” set of .100 oversize Pistons with pins. $100.00 set plus shipping. Lang’s 1-800-872-7871

For Sale is an original 1914 “Rubes” all brass Horn. There are 3 dents that won’t shown when mounted. $110.00 plus shipping. Lang’s 1-800-872-7871

Available again is Part # 3004B 1917-1925 water outlet made from high strength cast steel. $49.95 plus shipping. Lang’s 1-800-872-7871

Available again is Part # 3004 1909-16 water outlet made from high strength cast steel. $49.95 plus shipping. Lang’s 1-800-872-7871

IMG_0096.jpeg For sale are 4 new blockley tires and tubes mounted on new rims. I bought these about 4 years ago intending to use them on a project that fell through. They are mounted on brand new rims from Australia and I only put enough air in the tubes to mount them. Never were fully inflated. If you can use them, they will need to be picked up...

For sale EKERN rear axle emergency repair axle fixture. Fixture axle rotates smoothly And threads are in great shape. Grease cup was filled with synthetic grease for long life. Clamps onto backing plate. Used as a temporary fix to get you home after an axle break. Works on small backing plate axles only. Price $160. plus shipping. Call or text...

For sale 15-1/4 inch OD steering wheel. Steering wheel is marked Dodge Bros. twice, around each keyway. Price $250. plus shipping. Email, call, or text (248) 894-75fiveone. Thanks, Walt

For Sale brass 15-inch OD steering wheel with new brass nut. Single keyway repro. Price $300 plus shipping. Email, call or text (248) 894-75fiveone. Thanks, Walt

Very rare Weston Amp and volt gauge for an early electric car. Bakers used them and others. It could have other uses also. It is in very good all original untouched condition. It is untested, $975. I know it should be listed in the horseless carriage list but I cannot do it. Five07 458677eight. NO TEXTING.

I have a set of 4 new KW points available - photo coming later today - $65 includes Priority Mail in the U.S. Drop me a note through the Forum, please.

I'm having a brain cramp, what book lists the various bolt sizes used on a Model T chassis and body? Thanks, Art

I just saw a 26-27 T roadster pickup for sale in Longview, Texas by a salvage yard on Facebook marketplace. Price $2500.00. Ad states no title, no motor or transmission, and I do not see top irons or bows. Picture is not a close up, but it doesn't look like a rust bucket and fenders don't look all bent up.

Completely disassembled and cleaned, new float, float valve, venturi, and choke spring, reconditioned spray needle and spray nozzle, throttle shaft bushings installed and test run. $235 postpaid to continental USA email: wlkma9@gmail.com

Some years back RV Anderson reproduced a Watts style clutch. The price of the original material skyrocket and he used a ditterent material and asked some who purchased the kit to critique it. I have a 26-27 set up but am reluctant to install it fearing it wont work well. If anyone has experience with this clutch, good or bad, I'd like to hear from...

Removed mosquitoes.

smoked.jpg

Do you guys have a source for 21 tires other than Lang's or Snyders? Just curios if I'm missing something. I'm pretty happy with the results of my wheels and I just can't bring myself to put the old whitewalls back on. I have Kelsey split rims and only 1 of them is good. I saw a guy sell his rims and tires here but missed it dang it ;-)

Just...

Ford script T-2839 Wire wheel lug nut wrench. This is the original wrench supplied by Ford when you got wire wheels. $75 and $15 shipping. Email me at markpaulagember AT aol dot com

How about a nice set of 1926 Michigan license plates for your car. These can be registered and run as original plates. These were redone by Duane Wells many years ago. $125 and $15 shipping. Email me at markpaulagember AT aol dot com

Here is a good condition original 1926 copywrite Ford Manual that came with the car when new. It does have a couple of pages coming loose from the center staples. Otherwise in good condition. $40 and $15 shipping. Email me at markpaulagember AT aol dot com

Just as stated. A single 1926 Michigan license plate that is original unrestored. $50 and $10 shipping. Email me at markpaulagember AT aol DOT com

A brand-new Nickel radiator cap. These are not in stock at the venders. $25 and $10 shipping. Email me at markpaulagember AT aol DOT com

Model T 1926/27 Walker stamped ratchet style jack T2343. This jack works as it should. These are not listed often and are hard to find. $150 and $15 shipping. Selling as extra to my needs. Email me at markpaulagember AT aol dot com

This jack handle T2344 fits a ratchet type T2343 Ajax or Walker jack. $25 and $10 shipping. Selling as extra to my needs. Email me at markpaulagember AT aol dot com

This kit is for a 1920 or later Ford Model T and includes all the original Ford Script tools! Here is what is included: T1349 Hub cap wrench, T1387 Adjustable wrench, T1903 Pliers, T1917 Double end wrench, T2335 Cylinder head wrench, T2336 Oil Cloth Tool Roll (reproduction), T2336 Tool Bag (reproduction), T2337 Oil Can (can has slightly bent oil...

Great condition original single brass tube Ford script tire pump. (1920-27) Rebuilt by Vern Cambell several years ago. $150 and $25 shipping. Email me at markpaulagember AT aol dot com

6 fluted original steel oil cap. Plain top. (1915-16) $25 shipped to your door. Has intact screen. Email me at markpaulagember AT aol DOT com

Rubes Horn For Sale as pictured,

has reed and honks.

$225 plus shipping.

rubes horn.jpg

For sale: New wood for top of truck. bought from Classic Wood Products. $750 plos shipping
20250616_135906 - Copy.jpg

For sale: model t jack made by Pratt Mfg. of Chicago $40 plus shipping
20250327_170632.jpg

For sale: like new sleeve puller $20 + still has label with #2509 SP
spare tire clamp $10 +
NEW in package T-3063 X Manifold gaskets 1909-27 $3 +
Like new manifold clamps T-3065-E 1909-27 $5 each plus postage +
Oil pan supports $25 for pair plus postage
Motor braces $25 pr. plus postage
New mag spools $2 each or used $1 each plus postage
Pitman...

Hi everyone,
Just completed going through the entire Ruckstell in a ,26 Tudor that also has a Warford transmission. Having both I thought it a good idea to install the hydraulic disc brakes which I just finished today. Got everything put back together and started the engine to make sure the Warford shifted correctly which it did, however I could...

I recently inherited a good 17 engine sitting on a garbage late production chassis. I have been halfway looking for the bits to make make something usable out of this chassis but it needs everything. It would be easier to locate something better than it would be to find everything that this is needing. I just thought that I'd ask if anyone within...

This wheel/star with 6 holes is attached to the original choke arm where the wire goes. What is its purpose? It doesn’t spin, it has raised areas that lock it in place.

I'm surprised no one has mentioned the 1911/12 Town Car which is on facebook. This vehicle is in excellent original condition and must have been stored in a very friendly envionment for over 100 years. Their was a video showing the outside and inside which is remarkable condition it has since been deleted My Town Car is very close to this vehicle...

I have a 16 valve Roof, believe it’s a model A with oval exhaust ports and two 8 valve Roofs, one has a single intake port and the other has two intake ports. Would like to know what they may be worth? They have all had some repairs done, the dual intake 8 valve may not be useable. I think the 16 valve and single port 8 valve are useable. Please...

Need some help!!
Anyone have a idea who made this radiator shell?
Picked up at a auction and would like to know more about it
Thanks for any help
Rick.

I sold the Stevens Axle Tool and a person claiming to be me contacted the buyer. He wanted him to send him the money. He was calling from a 270-632-0562 number. I had several people interested so I don't know how he figured out who it was.

Hi everyone,
I just finished installing new axle shafts in a Ruckstell differential and I’m wondering if I did right to use anti seize on the tapers. Evidently there has been some debate on the matter. I also installed new hubs. Any thoughts appreciated!

I have two glass spare headlight reflectors. They are both the same diameter, but one is thicker and heavier than the other. Since the headlights are John Brown, I would assume the lighter one would be what was used. I'm not willing to remove the reflectors from either one of my '13s to find out!

I have a set of 5 brass T wire wheel hub caps & a set of brass, early block FORD caps available - $100 a set + the ride. Photos on request.

Reproduction hubcaps. Chrome plated. The one on the right stamping isn't as sharpe as the other. $60 SHIPPING INCLUDED. Dealers are asking $36.95 + the ride
ENJOY YOUR DAY!

Must sell out of room. Rebuilt engine/transmission, Rear axle, Brassworks radiator, New Brakes AC and parking, New Tires/tubes/rim liners. Numerous new parts, 4 rebuilt coils from Ron Patterson, 6 volt alternator, Stack of receipts message for more info. Over $15k invested. Asking $7500 IMG_4898.jpeg IMG_4899.JPG IMG_4897.jpeg IMG_4896.jpeg...

I have for sale an early Hall Scott Ruckstell shift lock assembly in very good condition. $250.00 plus shipping to the lower 48. Best way to reach me is through text message, my number is 419-217-8884.

How does one remove the front seat cushion ( back) on a 27 touring?
This one was recently re upholstered, looks like the covering is stapled in place, if so does this require pulling all the staples and then replacing them?

Starting to thin out the collection - some duplicates & now need new homes - I've been looking at this stuff for over 40 years ! Open to reasonable offers.

Hey guys I need more advice. 1926 Coupe here.

Problem:

So I have new triple gear bushings with 10 Thousands thrust.
The driven gear is pressed flush with the brake drum shaft.
New transmission shaft from Lang's.
Trans shaft installed as far as it will go and torqued to spec.
When I took it apart it had the three thrust washers for the clutch...

IMG_8553.jpeg I 30 back copies of The Vintage Ford,Model T Times, Secerts of Speed magazines and couple Eric Jarvis speed calendars. I would like to swap my back issues for Model T Times or Secret Of Speed. The Vintage Fords not complete sets but start in 2012. The ModelT Times 2000 up to 2017.
The Secrets start in 2000-2021. The calendar is from...

$2500 for 1919 T and all my parts

I made this pickup from a 1919 running gear. I bought the running gear that included the hood splash aprons, front fenders and gas tank. I added the cowl, windshield and seats. Added the rear box and fenders Runs great. no smoke. also a 1926 frame and wheels with a 1920 engine and rear end. All for $3000. You pickup at my house. Last time I drove...

I’m ready to put new sneakers on my ‘26 split rims and am considering going with 5.25-21. My engine is strong and I do have a Rux in this pickup. I like the idea of the slightly larger diameter tires giving me a little lower rpm at the same cruise speed. What have others experienced? Also, what’s the current opinion of the various brands that are...

Three Brass tire pumps for restoration or as is, manufactured by Bridgeport Brass company. $100 each plus shipping to lower 48. Best Way to reach me is through text message. My number is 419-217-8884.

There will be T parts and other pre war stuff at the Duncan Oklahoma swap meet. They added a pre war section last year. Us in the Midwest need to support this to keep a pre war swap meet in the area. I will have a booth and plan on bringing wheels, horns, tools, plates and many other items. Photos coming. Attached is a flyer. I went last year if...

Completely disassembled and cleaned, pressure tested float, new needle and seat, choke spring, reconditioned spray needle, test run. $195 postpaid to continental USA email: wlkma9@gmail.com

Completely disassembled and cleaned, pressure tested float, new needle and seat, choke spring, reconditioned spray needle, test run. $195 postpaid to continental USA email: wlkma9@gmail.com

For sale are three early transmission bands without removable ears. One says Ford the other two don’t $50 plus shipping to lower 48. You can reach me through the form or by text message. My number is 419-217-8884.

More stuff - make an offer ! The Hassler springs & cups are powder coated. One of the early oil caps appears to have been nickel plated ?

Does this date really mean anything for a Model T or is it only because it is used on aircraft?
Why does it expire? Looks like vaseline in a tube.
Thank you.

Hey there Model T friends. This is my first post in a good while. As most of you know already, I own a 1926 TT. I have not driven my truck all that much in the past few years and that it=s due to one central reason. Almost every spoke out of the 48 on the car is loose. This looseness causes the truck to walk all over the place when I'm driving and...

Does anyone know if there’s a difference between Canadian coil boxes and US coil boxes. I have a 1922 Canadian tourer… the coil box needs rebuilt. The wood isn’t the correct thickness and when the lid is on I short out coils….

I either want to buy a rebuild kit, or maybe someone has a nice rebuilt one ready to go for me?

Thanks for your help!...

I know the 2nd owner started a partial restoration on Daisy in the mid/late 60's after being stored since 1935.
Cleaning up the wood on her, while the firewall is original, the hood boards are replacements built by Syverson Cabinet, from their Des Plaines location they vacated mid 60's.
Just some continuing interesting archeology......

IMG_5109.jpeg IMG_4990.jpeg IMG_5044.jpeg IMG_5004.jpeg

1924 Cutoff Touring Pickup. $6000 OBO.
Engine serial number is August 1923.
Low hours on rebuilt motor.
Only ran on property a few times giving rides to family and friends.
Last run around 2010.
IMG_7593.jpeg
New body woodwork using Mel Miller’s drawings.
Professional paint.
Respoked wheels. 21” split rims.
Rebuilt rear end and new lined...

I am looking for a TT cab for a new project I'm working on. I have a complete running 26 chassis. My buddy found a TT flat bed with all the stock racks in amazing condition. I will get pics posted soon. Just seeing what is available within reasonable distance.

Has anyone ever taking an Aluminum replacement pulley that is not adjustable and make it adjustable?
I have one that is not snd want to make it that way.
Thanks Dan

VIN 13605442. Excellent condition. Was running when parked 8 years ago. Stored inside. Original engine and transmission as far as I can tell. Car is located in Spring Hill, TN and has a valid title. $12,000.

I need a couple of pieces of 1 wide black leather used is fine if its not to dry and hard. Does some one have a old broken front top strap for a 1911-12? Need a 8 and a 16 17 piece if longer that's great . Thanking you in advance for checking and any leads. Dave

Here are some Old School style rope type main seals that work good on T engines. One will do a T engine. These are about 6.5” long and 1/2” square. Fits the front seal just right. Fit it in timing cover, trim it and use the rest in pan. I have a good stock of these, but when gone there will be no more. If you want any better get them while you...

Hey all TW Timer lovers...by request I've been asked about any new runs for the TW timer. I hadn't planned to til 2027 but I reckon maybe I better. So I will take EMAIL THROUGH THE FORUM requests until Feb. 15, I strongly suggest you PLAN YEARS AHEAD.

Price from 2025 started at $19 ea. for rectangular brush, $27 for the round. You'd think it...

As subject line states...this is the last week I will take requests for brushes to be custom made for the TW timer.
See my listing in the parts section. Thank you.

Just finished up a new batch of Stevens Front Axle Repair inserts. Be out for a while. Sorry for taking so long, but life gets on the way. Have both Upper and Lower in stock now.
Upper Tapered inserts $6.50 each
Lower Threaded inserts $8.00 each
All are + shipping.
Email me by forum. Thanks Dan
IMG_0598.jpeg
IMG_2391.jpeg

Can someone please provide the measurement of the front top bow from the locking pin at the bottom of the iron to the top of the wood bow? Thank you!

It has a Rootlieb flat wood dashboard. I want to add a sheet metal cowl. more of a curved shape. Any ideas or does anyone have one for sale? or a blue print or patterns?

thnx
frontyboy.

Just respond here is the best

Get it for your grandkids! Get it for yourself!
To be issued in March.

LEGO 11376 Ford Model T celebrates the revolutionary automobile - Jay's Brick Blog

All,
The Bay Area Horseless Carriage Club is stepping in to take over the “Bakersfield” swap meet. The event will be the same location and date, Price per space will be 65 dollars. More information will be forthcoming soon.

This is just a quick announcement moments after the vote to let everyone know Bakersfield Lives again.

More to Follow

I am looking for the windshield garnish with swing arm bracket attached, for a 1923 Fordor Sedan. I believe the 1924 & 1925 models used the same garnish. There are some photos on this forum from a few years ago, showing exactly what I need. But have not yet been able to reach the gentleman that posted the photos. Any help would be greatly...

1915 Ford Model T Touring

This beautiful Model T is an excellent example of an American classic touring car, that was built in Canada in June of 1915 and still retains all original Canadian markings.

Originally purchased by Harris Fahenstock—whose family stood among the social elite alongside the Vanderbilts—this 1915 Model T was his preferred...

My mom likes hummingbirds and needed a lamp so I made her one. My girlfriend immediately asked me,”how many Model T parts did you use for that”?
She knows me too well and the answer is, a cut off transmission shaft flange, Holley G mixing chamber cover and one Model A brake drum.

I need to make a mother in law seat for my S roadster. If someone could give me dimensions, it would be greatly appreciated.

Thanks Jim