MTFCA Forum

Five early front wheel ball bearing races. Price for the lot (five pieces) is $25.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250516_112705.jpg

Set of four NOS bail handles. Not Model T by very similar. Can easily be adapted to work. Price for the lot of four handles is $100.00 plus $8.50 domestic shipping.

20250516_123733.jpg

I finally took George Akins advice and pressured my fuel tank using the exhaust on my 1924 Depot Hack. For years I have had trouble climbing hills unless my tank was completely topped off.

To the neigh sayers, there is no risk of explosion. Any oxygen in the tank is displaced by carbon monoxide. There is an aticle in the MTFCA Carburetor book...

Hotrod front spring perches. The consensus is these are used to put a Model A front axle under a T front spring and frame. They appear to be forgings and NOS as the threads are covered in wax. Extra to my needs. Get the entire lot for $100.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250516_122704.jpg

20250516_122731.jpg...

One steel crank handle (15-22). Appears to be NOS. Price is $30.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250516_112852.jpg

One early aluminum crank handle. Appears to be NOS. Price is $35.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250516_112841.jpg

One set of used ton truck hubcaps. Great for a patina or yard art build. Price is $25.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250516_123119.jpg

1916 Touring – Southern California ($8,500)

I purchased this car a few years ago to restore but unexpectedly ended up inheriting my father’s Touring (past MTFCA president and BOD). The engine serial number (casting date 6-12-16) matches the registration going back to 1956. The car runs on battery and magneto and is fun to drive. It can either be...

Six standard radiator caps. $25.00 for the lot plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250516_111213.jpg

Not Ford T; however, would look cool on a speedster build. Price for the set is $25.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250516_123413.jpg

An assortment of used Model T spark plugs. Clean them up and go! Price for the entire lot is $40.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_120107.jpg

Found these at a recent estate sale. Not likely T. Similar to Model A front axle spring perch. I'm calling on the antique car gurus to possibly identify the application.

20250516_114821.jpg

20250516_114850.jpg

20250516_114902.jpg

20250516_114914.jpg

I recently bought a speedster project and it came with an assembled short block with a drilled “C” crank (counterweighted Model A crank) and insert rods. The closer that I look at it, the more questions that I have. I don’t necessarily want to change any of these parts, but I would like to know what I’m working with.

1) What rods are these? I...

With a record number of vendors, The 2025 Luray swap meet was one of the best ever. The forecast of heavy steady rain for Friday, only turned out to be on and off showers in the morning, with the sun out for the afternoon. Friday evening's vendor dinner was wonderful as always. Saturday brought sunshine and still a flow of shoppers looking for...

Decent pair of 15 16 only head light buckets 100$ shipped lower 48 these are a hard find

A real time capsule - this car has been in my warehouse up on jack stands since 1963---

unadulterated - no broken glass interior is untouched .....asking $12,000.00

As some of you know, I restore Ford 6v generators (model T. A and flathead V8), and I refurbish original Ford generator cutouts. Occasionally I'll refurbish other brand cutouts too. Last weekend at the Luray pre-war swap meet I picked up this unusual Auto-Lite cutout with side mounted terminals.

It was dirty and missing some hardware on the...

Hello,

This is Steven Cross with Zink Motor Company Ford in Appleton City MO. I am wanting to see if anyone has photos of a T era dealership that includes closed garage door/s? We are a 112 year old Ford dealership operating in a 107 year old Ford designed building. I am compiling a project list for a local historic preservation grant...

For Sale is a nice Cross Drive Magneto Front Plate. Nice heavy iron casting. Has gears, shaft and plate side of coupling. Appears as though it could be used on the generator or pre-generator engines. Although not magna-fluxed I can discern NO cracks or other significant damage. I believe the oil spout cap is a reproduction but not sure. $425.00...

I would like to buy a block with a casting date between 9-1-13 - 12-15-13.

Let me know what you have and text me a couple of pictures to 901-496-8795.

Thanks.

Bill Everett

Cell: 901-496-8795

Taillight assembly for the improved car (26-27) with fender mounting bracket. This one appears to be in very good condition. No longer available from the dealer. Price is $100 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_113414.jpg

20250515_113426.jpg

One complete set of used front shackles in good overall condition. Includes new bushings, nuts and cotter pins. Price is $25.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_122051.jpg

Just a reminder that the Little Hershey swap meet put on by the Rockford Model T Club will be Saturday May 17th this year at the fairgrounds!
Screenshot_20250506_060825_Chrome.jpg

Dayton wire wheels. 30x3 1/2 Pin drive. Excellent condition.
These have been respoked using new nipples. Rims are very good. These come with s full set of hubs and caps. 5 wheels and 4 hubs. $5000. Can deliver to mtfca homecoming or pick up in northwest Ohio. If interested contact me through the forum. Jack Putnam

Only a few days away. Entice us all with your rare finds.

Andy

This week I finally added the factory pinstriping to the late 1911 touring car that I finished restoring in November 2022. A big thanks to Keith Townsend for providing pictures of the pinstriping on his car based on his research into proper striping that the factory did at that time.

I took it out for a drive today, but it appears that the...

Wow! June 7th & 8th is just around the corner. Well, as usual with my last minute antics, I just sent my entry forms in, and If you haven't already registered for the 64th Annual SCVMTFC speedster Endurance Run, time is running out. There's less than 2 weeks left before the deadline to get signed up. Without question, the best antique car...

Just bought a car with a distributor. Not sure who made this one. It is not connected to the timing lever. Should it be or does it have weights? Are tune up parts available? Thanks

Complete NRS Heinze coil box. I have not tested the coils, Real nice condition. Lid is new, the box probably should be re wired. $750.00. Kdmks AT att.net. Plus shipping.

An assortment of ten gas tank measuring sticks. Price for the lot is $20.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_120935.jpg

20250515_121035.jpg

The discussion on the use of coolant - what is the proper range for the Model T?

And how hot is too hot?

After reading up on the Model T battery-powered electric headlights, I have learned that the original Ford headlight bulbs had a 2 CP filament on Dim and a 21 CP filament on Bright. The filament was a teepee style oriented horizontally, the most efficient position to send light to the reflectors to be projected down the road. The locating pins are...

For sale: u-joint $75 plus shipping
20241029_175803.jpg 20241029_175747.jpg

new price is $50 plus postage

I renamed this post as I was concerned it was too similar to the already long discussed subject of rebuild and shim questions. This has been a very interesting and involved topic and, it is not my intent to hijack the discussion. Yet, I am hoping to have constructive criticisms and contributions to my post on the technical aspect of wheel...

Due to continuing health care issues, I regretfully have decided to sell my final build project that is beyond my present physical condition. It is a brand new, never been mounted
Richard Currier 1912 Delivery Car (C Cab) body complete.
I have continuing problems trying to post photos on this website so I have several photos of the body, always...

Recently bought 1924 Model T Fordor sedan. Side rearview mirrors would be very helpful. What do folks do to get side mirrors without too much damage to the car?

One very neat heavy duty carburetor choke bell crank. This one is substantially more stout than the Ford unit with a longer arm and a tension spring and adjustment nut. This would be great for use on a speedster build. Price is $25.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_103823.jpg

20250515_103804.jpg

Thanks to all who responded to my previous post. My 1916 with a 1921 engine is positive ground. To change it to negative ground I plan to:
1) reverse the battery cables
2) polarize the generator by briefly touching B+ to the field terminal
Should I disconnect the generator wire while I polarize the field (and reconnect it before I start the...

I recently received an aftermarket fuel gauge that I bought from Jay Buscio. It looks great, but age has taken its toll on the cork float. Do any forum members have any advice?
While searching for a suitable replacement, I found a source of straight sided cork on Amazon. It appears that the original has a coating on it, but I read that cork is...

Day one of the meet was awesome! I found some amazing parts! Hats off to the organizers!

I wish I could stay for Saturday, but work calls, (the curse of the small business owner)

You will not be disappointed if you're going tomorrow!

An assortment of generator parts. Two new complete brush sets and four NOS third brush towers. Price is 25.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_131712.jpg

One NOS roadster trunk latch assembly. Price is $20.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_120334.jpg

One early fan hub for the riveted blade fan blades. Includes the correct rear grease cup. The crown where the belt rides is in excellent condition. Price is $40.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_133128.jpg

20250515_133143.jpg

Spare wire wheel bracket for the rear of the car (26/27 Wire Wheel). One small split on one side. Easy repair. Price is $100 plus domestic shipping. Mark Chaffin (951) 805-0928

20250515_132001.jpg

20250515_132018.jpg

20250515_132037.jpg

Four used brass hubcaps. Great for your patina ride or static display. Price is $25.00 for the set plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_120551.jpg

i have for sale several single connecting rods ... these are re-babbitted and checked for alignment ... i can machine cut X oil grooves for an extra $15 each ... currently have Standard diameter , -.010 ,and -.020 ... price is $80 each NOT x grooved ...$95 each with machine cut X oil groove and drilled for dipper ... postage is included in lower...

Manifold clamp and bolt set (09-25). Price is $30.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_101547.jpg

For sale : Atwater-Kent model LA distributor complete with cap, rotor used point set and drive gears ... distributor is centrifugal advance and uses a separate conventional automotive ignition coil ...price is $150 plus $19.15 postage in lower 48 states ...actual postage outside this area or INTERNATIONAL ...Gene French 970-581-2808 or...

One top bow hold down clamp with wing bolt (25-27). These were once reproduced; however, no longer available. This one is in very good condition. Price is $30.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_103840.jpg

One SURE FEED accessory engine oiler setup for the four dip pan. In very good condition. Ready to install. Price is $45.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_101058.jpg

20250515_101118.jpg

Just a reminder that today is the deadline for Early Bird registration for the Homecoming Swap Meet spaces.

After today, the price goes up so call us before 5:00 (EST) to reserve your spots. You don't want to miss the event!

IMG_5392 copy.JPG
This gasket has holes for both of the center water passage openings.

IMG_5390 copy.JPG
The copper gasket has only one hole for the center passage.

Does the blockage of one opening have any significant effect?

WTB # 42 ignition key, But did not see this # on the key list. MY switch has 42 stamped on it, Any one else run into this? Thanks. Mike

Manifold clamp and bolt set (25-27). Includes new studs and nuts. Price is $30.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_103229.jpg

A gaggle of grease cups. Price for the lot is $20.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_100827.jpg

There have been a couple of request for Roof 16 Valve B & BB Competition Exhaust Manifold. I don't have a price yet from the foundry but have contacted them and they will cast them. I'm hoping the cost will come in under $600 a pair machined. If you are interested or have questions, please contact me. Once a price is established and we are ready...

Nice spare tire mount corner of the flage is bent and could probably use studs. I also have the Y forks avaliable if you have wood wheels spare carrier 70$ plus the ride

The 2025 Ohio Model T Jamboree will be based out of WOOSTER, OH this year. The dates are August 29,30 and 31. As always it is Labor Day weekend, and it is in OHIO.
There is a BOGUS claim on line which looks to be AI generated saying that it will be held in a different place on a different weekend.

Make no mistake the Ohio Jamboree is in Ohio on...

I have been a reader (learker?) of this forum for many years but have not kept up with it regularly. One think I asked about several years ago is still something I am not completely clear about. I am under the impression that the first jack appeared in a Model T toolkit in 1914. Some have argued that another Ford jack was used before that, such as...

I am looking for one of these (or two of the earlier style). If you have something for sale I would be very interested!

Thanks Scott

2025-05-14 19.47.44.jpg

As a Model K guy, it's always intrigued me that Henry Ford chose/allowed a Model K to lead the racers out of New York to St. Louis at the beginning of the race. As with most contests of the period, a prestigious lead car was always selected as the Pilot Car to enforce any controls and set the pace in endurance contests. A question that should be...

I guess I was pretty clueless on the availability of new stock replacement Scat T crankshafts. How long have you guys waited when buying one recently?

Can anyone refer me to a source for Medium Cream pin stripping paint, as used by Ford on 1926-27 enclosed cars?

One set of very good late style front shackles fit Ford script. Comes with new nuts and cotter pins. $45.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250514_142014.jpg

Here’s your opportunity to purchase unique display items. I’m selling a 1925 auto insurance policy issued to a school teacher employed in Storm Lake, Iowa for her 1923 Ford Coupe. The cost of her Model T is listed on the face of the policy as well as the engine number, premium price and peril coverage. Very good condition.

Price: $50.00 +...

This was from an auction about a month ago, and it sold for $175. What did I miss or what am I not seeing or aware of to command this price? It started at $49.99. Makes me think I should sell the nice cast one that I have.

can.jpg
can1.jpg
can2.jpg

Lamp lens on left has a high amount of purpleish coloration. Complete $185. Realizing FedEx costs are inordinately high, I’ll split shipping to lower 48 for only $20…
gwhouse731(at)gmail(dot)com

Only $25. Don’t think they’re being reproduced/in stock.
+ free shipping to lower 48.
gwhouse731(at)gmail(dot)com

I'm going to take a shot at this. I've attached a scan of a 1926 Michelin tire price chart that I found stuck between pages in ledger from my great-grandfather's store. Hopefully you will be able to download it and print a copy if you wish. It makes a nice wall hanger for the shop. Enjoy !

Does a muratic acid and water solution for rust removal eat away at brass or bronze fittings or bushings?
I know that a sodium bicarbonate solutions and a battery charger eats away at brass fittings.

Two very good Ford script universal joints in very good condition. Price is $50.00 each plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250514_141133.jpg

20250514_141233.jpg

Picked this up a recent estate sale. One 10 Tooth pinion with Ford script. Looks to be in very good condition. Price is $75.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250514_141046.jpg

I have a nice pair of One piece spindles, $1800 plus shipping, Send me an e-mail with cell phone # for pictures. Thanks, Dennis

Facebook link is for the Hank Lee M1 Rebel.

If you have not seen the build video, here it is:

Wanted to invite everyone to a great car show this Sunday from noon to 5 p.m. in downtown Warsaw Indiana. The show is a well attended charity show put on by the Optomist Club and they are specifically spotlighting
Early cars and Model T Fords. I'm a model T owner and am working the show so feel free to call or text me if are interested in...

Part of my rocky mtn brakes came off and vanished into the ether the other day. I don’t need a whole new set, but some of the parts that went missing on my country drive. Where can I get just some replacement parts?

Need the goose neck mount that mounts on the bottom of the spring'
Thanks, Bob Giles

Up for auction is a very nice 1922 Model T centerdoor sedan in Monroe Winsconsin on May 13 2025
Auction company is George's Auction service.

This car is built for touring!
It has a Rajo head, ruckstell rear axle, auxiliary disc brakes on the rear, model a crank and rods, turn signals, fatman steering wheel, 12v, and much more!
This car is right...

Yesterday my dad and went for about a 70 mile run with my 22 touring. This is the longest trip we have taken with it, although last weekend I put about 50 miles on it. Last weekend the car ran great and this weekend it ran great for about 30 miles. Then, while running about 35 mph, the car started surging. I would throttle down and it would clear...

Cleaning out the top of the barn. Foreign to me. Threaded portion measures 3 - 10 TPI. Large flange is 7 3/8 . Overall height 6 . Rear bearing hub diameter is 3 1/8 . What manufacturer, what size? Thanks!
431DC0BD-9A91-4AD1-A294-23399ED8C0B8_1_201_a.jpeg
E6D25CDD-5D2A-4BDA-888F-E6D8CF7038BD_1_201_a.jpeg...

Is there anyone inthe Columbus Ohio area that would be willing to check out a Winged Script radiator that is being offered for sale at Buckeye Auto Parts at 2474 McKinley Avenue in Columbus? I just want to know if it is legit.

These lug nuts from Chaffins look like Jewelry.

Was the model T screwdriver in tool kits from 1908-1920?

What is the thread size on the starter switch posts?... Thanks in advance.

FS KR Wilson Model T Ford Pan Jig $1000.00 Free delivery to Luray Swap Meet in May. Can be shipped on a pallet via truck.

Langs Old Car Parts
www.modeltford.com
1-800-872-7871

Good evening all,

Looking to buy a set of restorable 1914 headlights preferably E&J but will accept the other brands.

I have good mirrors to start with.

Gerry - 510-332-9588

Poll:
How low can you run the fuel level in a cylindrical, under-seat, 10-gallon fuel tank?

I’d like to put something out there that never really seems to get mentioned about the Prus head. Of course the power difference it offers is a noticeable improvement on our cars, but the one aspect that seems to be overlooked is what that additional compression does for the engine’s retarding ability on long downgrades.

I live in the flatlands...

A few more Town Cars.

Helping someone identify the year on a center door. The engine is a ‘22, but it has a metal firewall. It is my understanding the metal firewall didn’t come along until mid ‘23. I assume a 22 center door would have a wood firewall? Is it possible that someone rebuilding this years ago put a metal one where there was wood, or is this likely a ‘23?...

I am looking for a good coil box lid for my 1922 . Let me know what you have and and want for it.

Making room for bigger and better toys! Bought this photo etching kit bout 10 years ago to make some hub cap emblems for a fella… and never used it. A bit dustier than when it was new, but otherwise complete and unopened. $40 plus shipping

IMG_3066.jpeg IMG_3067.jpeg

I have an assortment of Stewart parts available - more than I need for spares. If you're seeking something in particular, drop me a note through the Forum, please. I'd take $150 for the Stewart spiral drive parts (3 pcs.), either road gear - $40 each - all + the ride.

Forgot to a Stewart head - broken glass & rubbed numbers on the mph wheel but...

Just putting this out there if anyone is interested. I plan on being there Friday with some odds and ends. Maybe a HCCT, a couple different rod alignment checkers, some pullers and excess tools. Maybe a set of wire wheels and hubs.

IMG_9775.jpeg

Model T Roadster Pickup with 1924 Engine

1924 Engine, 1925 Pickup Box, 1926 Rear End

Rebuilt mechanically from front to back. New rubber. Crank start.

Includes engine stand, Model T tool set and misc. parts and tools.

$12,000.00, Contact John @ 320-582-1737, Hutchinson, MN

mtfca1.jpg

mtfca2.jpg

20250507_104403.jpg

mtfca4.jpg...