MTFCA Forum

Norman is so right with his advice to check the magnéto and coils but I would like to add this to the comment.

Sometimes the reason of not good or not at all working of the magneto is brake band debry between the magneto coils.
See photos.

Good luck.
Andre Belgium

Dan; Did you receive my e-mail? My computer isn't working wright so I don 'know if you answered. Craig

It uses the same exhaust manifold as stock if it has the flared end. The pipe itself that Mr Smith made, just has the correct bends like the original.

Email reply sent

Thank You all for your information, that is what I thought it was but the twist on the jaws made me wonder. ——dan

Or, he has the flat top aluminum piston sold by every supplier for the last 50+ years (not domed/high compression)...I am going to go with that...

I’ll bet those are Ford factory spacers you have pictured. But that’s a guess! Always something new to learn about Model T’s for sure. It would make since to use shims there also.
Interesting for sure. I can’t recall this being brought up on the forum before.

As most of us know the one piece coil ring spacer and the individual spacers are...

No, standard early E & J - I'll look George - I might have an orphan or two.

Tom, I would be interested in a few If the price was reasonable.

Picture of threads

Jahn, I used 9/64 diameter x 0.25 hollow-body rivets from McMaster.com. They also have hollow-end rivets.

There are additions to the carrier as well. Ay each mounting point an extra piece has been welded in to allow the carrier to be hung from the top of the frame rail rather than bolted to the sides of the rails. I have no idea why this was done.

Tires sold pending payment. Frank

Still for sale

FJ

to the top. see other postings. Seeking perhaps $2200. What do you think.?

seeking perhaps $2000 picked up in MN or you pack and ship -or have someone do it for you.

Be careful. Caps for Bosch front plate distributors are not the same as caps for clip-on style distributors.
thanks for the heads up! I’ve been doing research till I am blue in the face. Is this cap one for a clip on? I noticed a different part number and manufacturers logo.
Bryant

I believe the one shown by Sir Tim is for a clip-on. Notice...

Mike Coats, are you any closer to discovering the source of the extra electricity.

The spark voltage from the coil is the only voltage that is high enough to provide you a shock.

That high secondary voltage comes out the bottom button of the coil and it is a very short trip from there to either one of your coil primary voltage sources.

to the top

to the top[

Thanks Mark!

That is perfect!

The floor boards were going to be my next question!

So, I got two birds with one stone! Thanks again!!!

To add to George M's historical context comments, I should point out that 1904 was an election year. Just ten weeks after the Malcomson non-vote meeting, an election was to be held. Teddy Roosevlet had assumed the Presidency in 1901 as the result of the assassination of William McKinley. The election of 2004 would determine whether TR should be...

-
I went to look at this “closed car” on behalf of my always cold 93-year-old father. It’s a solid and respectable Model T build by a solid and respectable Model T-er. The interior is excellent and any blemishes on the exterior are so minor that they wouldn’t be worth fixing. It also has those mechanical upgrades that make it a good T for touring....

Sold to Phillip. Thank you.

which one?

$40 plus the ride!

move to top

Going to Knot county Kentucky for 5 days the week before OCF. Too much going on and still working out of town alot. I will miss the ride in the speedster but your taking the touring this year anyway.

Prices reduced on remaining items as indicated above.

Price reduced to $45.00 plus shipping.

The last two cars were Fords, so we cleaned up the track behind all the others, although we left a few brake pieces on the road.

Most fun ride I ever had at NLNB. Thank you Roddy.

That makes sense. Maybe we complicate things a little by what we have to deal with when we buy parts to day.
Craig.

John; As already stated, you actually can rebuild your old coils....maybe, with a big tarry mess... but there are two guys on this site that do it professionally and either will supply you with a set of rebuilt coils at a very reasonable price that will probably outlast your car, and maybe you as well. No more hoping that your work will pass the...

Good catch on the Horn... But I'm not really sure but that it could be correct? Mine has a different horn but a later build. I think I'd be happy driving it after a good cleaning and the seats and top don't look too awful bad from what we can tell in the pictures. Just thinking a good wash job and an engine/coil tune up with some air in the tires...

E-mail sent.

Thanks MAG.

I bought the one above from him, but wouldn't mind a few spares kicking around.... If anyone else comes up with something.

Thanks!

I have known Doug for a number of years, one hell of a guy.

You got that right!

I just saw this post. I had a late-28 AA truck back in the 60's that had that exact whistle on it when I bought it. The whistle worked very well and just like Jerry was thinking, it changed volume, not pitch/tone. It had a real nice sound, different from most other whistles I have had or remember. It did have a bad habit of getting stuck if you...

Thanks to all that contributed pictures and details of the many variations of Fronty (or similar) water manifolds. And a BIG THANKS to Dan, who sent over an original!

It seems that no 2 are the same! If you look close enough, the main differences are in the various fillet radii, and a few have rotated mounting flanges on the outer ports, and the...

Yes this year’s was a very good one and no doubt yours next year will be a good one also.

Found it, I knew I had one.

Price reduction $5,800. fun to drive.

The car is being prepared for long term storage and is no longer available.

Very cool

hopefully it finds its way to a McCord Gasket Display and not into an engine

#1 sold the the gentleman in the great state of Texas!

What an informative thread. I'm going to go check mine. The rear end was my next project anyway.

Based on my experience, I would dismiss ethanol gas as a likely problem unless it's very old. I use it, and haven't had any Model T problems that I attribute to it. Of course, I drive enough to use it up before it can go bad .

Did you speak with Russ Furstnow?

Hi Scott, yes, he only knew of one car for mid-$20's. I don't want to spend $25,000 on a T.

While you are at it, chase the threads of all the bolt holes and blow out with compressed air. Before doing this, using duct tape, tape over all water jacket holes and cylinder holes to prevent metal shards from going into the holes. Tape over the threaded holes not being cleaned out for the same reason. When installing the head, stagger the...

FWIW - the Service Manual does in fact direct the mechanic to both fill the hub cavity with grease as well as fill the hub cap with grease.

I believe that was a direct reflection of the quality of the grease used during that period, and the fact that the car was expected to see much more severe and wet service than we typically do today.

I...

I've put many a seat in and have never lapped any but it takes experience to know what to look for. .060 width is good for gas motors. You could put a larger valve in to deal with the worn seat but it requires more seat grinding of various angles to get the seat width and diameter right. You also don't want a valve seating on the outside edge of a...

Is this the same Ames Co. that made every sort of shovel, pitchfork, hoe, etc? Are they still around and actually making implements in the USA?

Thanks everyone that really helped. I bagged and tagged everything but I can't find these ones. I'm sure they are somewhere safe.

All the plugs are sold

Not speaking from experience here, but from what I recall reading from some earlier discussions. I believe that the Stipe 280 cam does not have the advance built in, but rather is stock timing with just the increased lift. The Stipe 290 cam rather than just having advanced the timing has been designed with a different timing, duration, overlap,...

These are now sold

The S7 is probably the pattern number, so if they had flaws, they would know which pattern was causing the problems. Patterns have only a limited life, based on how hard they are used.
I have some REO running board brackets that actually show the wood grain from the pattern, as they were too cheap or too careless to bother with touching up...

Bryant is right. The grease stiffener (soap) can react chemically with other types of stiffened grease. With the exception of wheel bearings, I use lithium grease for lubing everything. Lithium grease is very common and sold about everywhere.

Art Mirtes

Sorry guys but an airplane will be in the trailer on the ride back home.

20220806_194251.jpg My opinion is like someone else said about the suicide door coupes on the forum before, if it was after June in 1923, it wasn't a 23, the 24's were out and they were redesigned and the doors hinged from the front and states varied as to what year they gave the car. I know someone will say they have a 23 with the front hinged...

I get next set!

WILL TRADE FOR A MODEL A OVERHEAD.

Another one got away.... gone like a new copper head gasket.

I would say, leave it as is. Unless you can PERFECTLY match it, so it is impossible to detect. It is only original once, and like a T with the original paint, it will always be restored or repainted if you change it.
Norm

This one showed up to a car show this weekend. A local retired Fireman bought it and passed it on after he passed on.
DR08.jpg

Along with adjusting to being a year older each year we are getting used to the local car interest changing. A few low riders were there with the trick suspensions. They put as much work in their cars as we do.
DR55.jpg
Our local club has many new members with later cars. We couldn't get things done without them.
DR47.jpg
Friday evening there...

How can you be looking for an inner tube stem, when you don't even know the size of the tire?

evidently Toooo many beers again ?

Great truck and a great price !
Wish I could.

You got it. I'm sure you will be happy with it!

I have an original cast iron unit with the distributor. When I bought it the front plate had no bearing or bushing where the bottom of the distributor main shaft would be supported. Is this correct?

I also have one of the aluminum reproductions and it has a roller bearing at that spot.

Thanks,
Howard
Howard I also did not see any bushing in...

RIGHT ON Pat!

Civilization is on a fast track to total annihilation. :cry:

My address is 21346 s 80th ave. Frankfort IL. 60423
WillieT