MTFCA Forum

2 tubes that were on my TT up until last week.
Hold air with no issues.
Brass stems and hardware.
$20.00 for the pair, plus postage. Pm please. Many thanks. Marked ANT USA.

Having spent 4 years in the Marines from 1972 to 1977 and running 3 miles a day, it destroyed my knees. It has been 48 years since my discharge from the Marines and I have waited as long as I can. I am almost a cripple and it has finally come to the point where I need to get knee replacement surgery. I will be having the right knee done on July 25...

I am looking for a nice Wood Wheel Rear Hub for a 1926. If someone has one to sell and is coming to the Owatonna Tour in a week or so, that would even be that much better as it would save on boxing and shipping.

TIA

There is a pickup listed for sale and it says new U channel. Is that the piece that goes down either side of the frame from behind the bottom of the seatbacķ on a roadster to the rear of the body and connects to the floor under the turtle on a 26?
If that is it, are they available or do you manufacture your own?

That piece on my 26 pickup is...

Vanderbrink Auctions has an online only estate auction coming up in Montana It has lots of early stuff with some Model T cars and parts cars. Other early cars. 1909 REO is oldest to 1960s era with some later stuff. A huge auction with a good selection of cars, trucks, tractors, hit miss engines and other unique stuff. There is a 1915 Couplette...

Here’s a very nice original brass, left side, Dayton wire wheel hubcap. The spring tab is strong and works well. The threads look great. $225 with shipping in the US.

IMG_5785.jpeg

IMG_5790.jpeg IMG_5788.jpeg IMG_5787.jpeg IMG_5786.jpeg

I’m in the process of getting my re-wooded 25 (August 1924) Touring ready for paint and was able to get the firewall done today. I’ve never noticed these holes below the choke bell crank or the one with a shoulder directly below the coil box mounting holes. I don’t remember my January 1924 Roadster having them. What would they have been used for?...

I recently had to replace my original 1916 round gas tank. the left end had been cut open by a previous owner and poorly repaired. When it started to leak last year I attempted a repair with JB Weld's Tank weld. It held a year but I pulled on a loose end last week and it pulled right off. Due to time constraints I ordered a new tank from Kevin...

20250713_141651.jpg 20250713_141656.jpg 20250713_141703.jpg

Two speedo cable sheaths only. Both 65 . I believe Mr. Furstnow can shorten these if needed.

$30 each + $10 shipping.

Contact via forum. PM or e- mail.

Check or PayPal

Not one auto parts in my area is carrying conventional motor oil, Its all either a full synthetic or a blended synthetic oil. I was lucky to find a five gallon pail at my local NAPA of 30# conventional for the model T which should hold me for a very long time as I don't drive the T very much anymore. I was running 15/40 Rotella but thats even...

I am having knee replacement surgery on July 25. Anyone who has undergone this procedure, please read my questions on the OT forum. Thank you. Jim Patrick

Set of roadster top iron body brackets. Right and left with top nuts. $50.00 plus shipping IMG_2190.jpeg IMG_2189.jpeg

The time is getting closer for Miller Ferry and the Yacht club to know who is coming this Sunday for T day on the island, if you have never been there they treat you very well on the island for refreshments before the parade and a lunch after. Line up is by 9:30 for the 10:00 boat. I do not plan on doing this next year so this may be your last...

Looking for a pair of ‘26-‘27 tail lights, (actually I think they started to use the drum tail light in 1924) one license bracket and left and right fender mounting brackets or any of those parts.

Hello, my name is Kevin and I just purchased a 1923 Ford Model T Tudor. The car is very complete and original looking. It needs a few things to get road worthy. One thing it is missing is the gas tank. I've been a car guy all my life, so not new to cars. My question is this, where does the gas tank reside in a Tudor? The information I have read...

FS: A Holley Model G carburetor, in barn find condition. Cast iron body with brass top. The choke and throttle are not seized, and I don't see rust-through on the bowl. Asking $25 not including shipping.

THG01.jpg

thg02.jpg

thg03.jpg

thg04.jpg

Thanks for looking!

Anyone ever come up with a good way to rebuild the worn cam ramps on pedals? Hate to scrap a bunch of them if way to repair. Thanks Dan

I'm putting my car back together after removing the steering wheel, firewall and etc. in anticipation of some engine work that has been postponed until winter.

I went to connect the commutator rod and when I tried to connect the swivel end, I couldn't find the nut. No big deal, right? I went thru my entire collection of nuts, both SAE and AN...

71st Long Beach Model T Club Swap Meet is coming fast! Saturday July 19 at Long Beach City College Veterans Stadium 7:00AM. Visit lbmtc.com for flyer, registration form, or details. Don't miss one of the oldest and best Model T, Model A, and Old Ford swap meets in the West!

I have 1926 model T roadster. Cannot get NH Carb to quit leaking gas from the throat.
New viton tip needle valve and seat and new float, all gaskets replaced. Adjusted float level to 15/64ths, works on the bench but as soon as it is installed it leaks a stream. Leaking stops when air screw is screwed all way in.
Anything I’m missing here? Replace...

For sale a pair of very nice headlmp mirrors/reflectors, These were removed from a pair of Jno Brown 19's. They are 6 in Dia. and are in excellent condition with no chips or scatches, These will make an extronary pair of mirrors/reflectors once resilvered. Asking $195.00 plus shipping. Please contact me via email or phone through the forum system,...

Are WASP 12V starters still being made? I see that Snyder's is temporarily out of stock

20250713_092320.jpg 20250713_092334.jpg 20250713_092340.jpg

One repo brass open car mirror.
$75 shipped to lower 48
Contact via forum pm or email

20250713_092131.jpg 20250713_092127.jpg

Two pole accessory switch. Works. Needs cleaning.
$50 & $10 postage

Contact via forum pm or email.

Restored as pictured, only needs a large cotterpin! $35 which includes 48 state domestic shipping. Contact me thru the MTFCA email messaging.

Getting ready to paint my brake drums. I would think a high temp paint would be a benefit. Does anyone have a recommendation on a good paint to use?

Curious if one is out there.

20250713_092251.jpg 20250713_092256.jpg

I decided to go another route. Cast aluminum.
Fits well. Unknown mafg.
$200 & $25 shipping.
Contact via forum. PM or email is fine.

20250713_092155.jpg 20250713_092245.jpg 20250713_092248.jpg

Bought for $300. Will take $200 & $30 shipping
Contact via forum. PM or email

20250713_092150.jpg

Brand new repo Boyco caps for show car.
I have decided to go another route.
Paid $200, will take $150 + $6 postage

Contact via forum. PM or email

Posting here in hopes of getting some help. My wife is in love with the model k. She saw one when she was a kid and I’m hoping someone here has one close to New England and would be will for us to come look at it and even possibly get a ride for her we have a couple of model t’s if you can and are willing to help do this please reach out via text...

Set of 3 transmission drums for model Ts 1926 and 1927. These drums have been cleaned, checked for cracks by magna flux and have been precision ground and polished. The gears are excellent and tight. Brake drum uses replaceable shoes. Original bushings are on place and could be used without replacement. This is a great set of original Ford...

This horn measures about 10 long and about 5 in diameter. It is made by the Maxim Automobile Supply Mfg. Company in Brooklyn, New York. It has a brass bell, a three-hole mounting bracket and the original bakelite wire knobs. I would assume it would be from about 1913 to 1919ish. A good looking horn and in good condition.
The price is 195.00...

Here is a neat, original automobile plate. Embossed tin. 3 by 13 . Made for a car. Detroit Automobile Club, Protected Inter-Insurance, AAA, Thieves Will Be Prosecuted etc. The price is 200.00 including FedEx Ground including insurance in the USA. Call me directly at 734-730-4274 or email directly at motoringicons@hotmail.com Thanks.

For Sale: one set of shackles. Ford Script.

$110 includes shipping to lower 48

shackles.jpg shackles 2.jpg

This is the earliest announcement-article I’ve seen of the impending Model N. While many things are incorrect (wheelbase, opposed cylinders, $400 price, etc.), many are spot on (cylinders cast in pairs, horsepower per pair-8, etc.).

IMG_8724.jpeg

Anyone doing coil testing and tuning located in nothern ohio.

Thank you

johnr

High quality very authentic older restoration, correct body color, dark green that appears black until you get into the right lighting. Open valve engine one piece pan etc etc. Very nice throughout except for each fender where the mounting bracket is, has paint cracking and chipping. The car was restored in the late 1970s and within the first 3 or...

IMG_2880.jpeg IMG_2839.jpeg IMG_2857.jpeg IMG_2853.jpeg

Took delivery this past week of a car delivered by Bill Auto Works. Fantastic service by Bill Squires who was very easy to deal with, very commutative. Always called to report progress with on time delivery. Quoted a price up front and stuck to the Quote. No surprises. Very professional, would use again.

Hello,
I am looking for a really good set of gas headlight mirrors for my 1914 Model T. I have a set of the nickel plated brass reflectors and halogen bulbs they sell at Snyders and Langs, but I would like something brighter if possible. I think I could get a little better headlight performance from a set of original gas headlight mirrors. Does...

It's always fun, to me, when working on the T, to look for where there is 'Ford' stamped into each and every part. I thought this would be a fun thread to have, posting pictures of all the 'ford's on our Fords. :)

Here's one, on a rear axle shaft.
Where's the ford on your car?
20250701_175001.jpg

Hi.
Meanwhile I successfully replace the roller timer by a new (similar) one.
I also verified the distance of 65mm / 2.5 between spark advance rod on timer and the screw at oil fill socket.

Because the battery was empty, I connected the battery charger and tried to crank start the engine for first test run while the battery is charging.

Of...

Hoping to build a thread with any history on the “Giant Speed Equipment . I’m guessing they were active in Los Angeles area in the 50s or 60s? I picked up a Gemsa flathead for my T, and noticed how similar the lettering was between the Gemsa and the Giant.

I think I know the answer but I will ask anyway. I just installed a Texas T Alternator on my 1918 touring. I did not realize that it is a 12 volt alternator. I use an 8 volt battery because I like it and I want to. The question is>>>>Is it OK to have this 12 volt alternator with an 8 volt battery. If not, what are my options besides taking the...

Big car show today The Ford dealership is well worth the drive. Zinc Motors, one of only 2 dealerships in the state of Missouri that still operates out of their original building. A building that Henry Ford designed. If There is any interest in interior pictures, I can add more pictures next week

I sent an email to one of the Officers (Don't remember which one) wondering who i s the ninth Board member. No response. Now I'll ask all of you, is there one? If I hear from no one, Ill have to go back to my old records and check it out. TIA

New to model T car I acquired is missing the carb heater.

-
Hello fellow Model T-ers,

I am looking for a Mercury, or Paco, or similar period correct bodied speedster in restored condition.
Would any of you know of one that might be for sale. I am aware of one in Sweden. Area code: (323)

Steve
497+ ...0601
-

What have you done to/with your Model T in July?

Was so excited to get our new starter that I installed it last month and tested it out - problem solved.
This month, I removed the starter, made a gasket and installed it again - still starts.
Like the old saying someone wrote in my high school yearbook: Don't wait until tomorrow to do what you can...

I am looking for replacing some bad wheels on a 1909 REO touring car. If you would know of any parts please advise. The hubs seem to be ok.
Thanks

Looking for a brass windshield, if it has glass can drive to Arizona/SoCal/New Mexico?

Anyone happen to have any literature on a LF - diagrams, cut-aways, etc ?

Screenshot_7-3-2025_10813_www.google.com_.jpeg

We've got this project for sale. Mostly correct 1915, and mostly complete. See the photos. Engine casting date of 11-9-1915, makes it a 1916 model, but still eligible for HCCA events. The front half of the body has the wood replaced. The rear seat is off and disassembled. Correct and solid fenders. Has demountable wheels but 30x3 non-demountable...

I am donation our family 1915 Model T Touring car to the Sherman, CT Historical Society. I live in TN. The car is going back home but the team that will garage and drive the car isn't familiar with the 3-pedal Model T. I'm searching for a person that is willing to teach the Sherman, CT Model T care team how to drive the car. George Akin, President...

I know these aren't for Model Ts, but, you never know....I need 34x4 or 35x4 1/2 CLINCHER tires for 26 wheels. Condition could be fair to excellent. I can use one to five. I don't want straight side, I have a new set of those . I could also trade the new straight side 34×4 set for a new set of 875x105 clinchers. Thanks. Email at motoringicons (at)...

Due to the unavailable reproductions of 26-27 enclosed car window crank handles, I, like everyone else, has had to resort to using the reproduction Model A handle that tightens with a set screw on the regulator shaft. I have seen window crank handle that reportedly are original Model T, but the handle has a big hole in the outside and is held to...

Model T Roadster Pickup with 1924 Engine

1924 Engine, 1925 Pickup Box, 1926 Rear End

Rebuilt mechanically from front to back. New rubber. Crank start.

Includes engine stand, Model T tool set and misc. parts and tools.

$12,000.00, Contact John @ 320-582-1737, Hutchinson, MN

mtfca1.jpg

mtfca2.jpg

20250507_104403.jpg

mtfca4.jpg...

1910 touring, original saddles, reproduction top sockets with the following measurements:
Top socket width 1-45/128
Saddle gap width 1-27/128

Now what to do?
Does anyone have a pair of top saddles that have a wider gap that are the same profile? I think the early saddles are cast so heating and bending is out if they are cast I suppose & would...

Ok, I know this magneto has 2 more terminals for this crowd, but there might be an early six cylinder person that needs one. Brass base. Has the original Bosch bakelite knobs. Clockwise. Gives a good spark when you spin it. Good condition, complete, not tampered with, etc. A good magneto. Price is 495.00. Call me at 734-730-4274 or email me...

I have these two original parts available. New reproduction are $79.95 each plus shipping.
These are $60 each with tracking postage delivered to your door. Either one, or save some postage if you want both.
20250705_163847.jpg
20250705_165854.jpg
Allan from down under

Planning ahead, I would like to be able to use my Gas Headlamps at OCF parade or at a evening Cruise-in display. I am on the fence on whether I would like to use a small 10cf tank of Acetylene, -or Carbide (-see link below) in my Carbide Generator tank. How much difference in light (Lumens??) output will I see with one type of fuel over the...

Largely original 1911 Touring #552xx, May 1911. Ex Sherwood and Lang. known history to new. Mechanically rebuilt including engine and transmission by McTavish. Beautiful original upholstery. 90% original sheet metal. Way too nice to restore. It’s only original once. Runs very well and has been toured. Combination of 50’s and early 2000’s paint. A...

Has anyone used or made work a Ruckstell or Hallscott shifter on a Perfecto two speed rear end? Thanks.
Craig.

Is this mag drive for a model T?

T died on the road. The starter turned the engine. I got no buss at the coils. Fuse I have in system ok.I ran a wire from pos post battery to bottom of coil box. Got coils to buzz, car to start and got home. So where is problem? Switch?

For sale pair of red painted wheels with steel fellows and steel spokes in good condition asking 250 for the pair plus shipping or can deliver to Hershey text or call 2036873827

Would anyone recognize what company made this rim and if it was made by Ford or an After-Market Company?

Rim.jpg

Seeking a headlight socket (thimble) 6574-X, new or old. Thanks!

Looking for a set of side curtains for a 1926/27 Roadster with Irons, any condition will work, Jim

I'm in need of a pair of running boards of the 1913 to 1925 vintage. Dont need be perfect but should be respectful and worthy on new paint. Please reply using the forum message.

Looking for a 1915 cowl lamp or two. Black and brass type.

Thanks

Manny

Completely disassembled and cleaned, viton tipped float valve, tested float, new choke spring and ID tag, test run
$185 postpaid to continental USA email: wlkma9@gmail.com

slwa_b2600780_6.jpg

slwa_b2600780_5.jpg

I ran this on my 1912 van for 25 years. The car got hard to crank start so I replaced it with Stan Howe rebuilt spare. It turned out that the hard starting was due to a shrunken cork float that was very loose on the hinge so the float level was all over th place.

It will need a new float. It may be better with a viton tip needle and seat, and a...

I have a tire issue I never ran into before. I have a good 21 inch tire that was low in air. I pumped it up to 35 Lbs and all was fine. I then checked the pressure with a tire gauge and the gauge read 0 PSI. I checked and no air will come out or go in. Same when I removed the valve from the tube. Tire is aired up but no air will go in or come out....

I have owned 1910 T number 24146 since Sept, 1946. It is a good carand mostly complete or the 1910parts needed go with it. If I do selll it, it has to go to a local person who will take good care of it. When an local person looks at it, I them will quote a price, but only to someone who will keep it. If I do not find the right person, I will keep...

I am sure a common front fender problem. A tear as seen in the pics. I had the same issue with a previous roadster.
I paid a fortune to repair, only to have the repair begin to crack. The fender was repaired while it was off the car.
I think the stress of reinstalling may have weakened the repair.
I'm thinking to repair this fender while still on...

I have a have 6 pack of the hundredth anniversary Ford Coca-Cola bottles, in Curtain, for sale. It is in pristine condition and from a smoke free home.
I am asking $20 per six pack, plus shipping to the lower 48 states.

IMG_6369.jpeg IMG_6371.jpeg
SOLD.
1909 - 1912 Brass Windshield Frame Complete with glass setting Channel, came from
Snyders T-40300, it is still wrapped in original packaging. $350 plus shipping. Call
With any questions. (740-501-5888)

Hi Everyone. I have been wanting a Model T for a long time and finally got one. I picked up a 1917 Touring that has been converted to a pickup with the Ford metal pickup bed. It's a project and not restored (what I wanted so I can learn about it). It also needs upholstery work and its missing the wood backrest frame for the seat. Its pretty...

I'm adjusting the coil points for a 1913 KW Coil. The points that are on the coil are the ones that Randall (RIP) Anderson had made about 10 years ago.
On the upper, top point. the cushion spring is way greater than it should be. I just checked a NOS late Ford script coil point, and that setting is .009 .
I'm thinking of gently smacking the rivet...

I have a set of Cartouche Side curtains for sale that will fit a 1915 through 1922 Touring car. The eyelets are brass for 15/16 as opposed to nickel for later years, but they can be changed out if you so desire. This set is about 20 years old but in excellent shape and still very soft and pliable. The windows are perfect. You may need to move your...

Best Possible quality rebuild.
PRICE DROP! $325!!

Now that I make literally every part in these units except the housing and the armatures, I can pass some savings on to everyone.

I have ONE 6v starter for sale that I just finished putting together yesterday.

New field coils with silver soldered post (yes, I now make these)
Bronze bushing...

Want to buy a small drum standard rear axle for my model T.
Frank. Eight one eight two five four six seven nine seven.

1915 hood former great shape. $150 plus shipping.

Anyone from Idaho going to the Long Beach Swapmeet July 19th ?

I have some parts I need to get to and from another member.

AdminJeff