MTFCA Forum

Looking for a Model T service provider in SE Wisconsin. I have a 23 Model T Tudor that I would like to have the engine tuned up.
John Cleary

Looking for a Model T service provider in SE Wisconsin. I have a 23 Model T Tudor that I would like to have the engine tuned up.
John Cleary

WTB Driver side REAR Flat Top Fender for 1915 Touring Car.
Contact Eric Gould, Monroeville, AL. Email me here on Forum.

For sale: Ford script wire wheel hub caps all for $65 plus postage
20241027_101908.jpg

20220721_195820.jpg 20220721_195926.jpg

For sale: brass hubcaps. $45 plus shipping for all 3

The weather was perfect for a drive with some speedster friends. IMG_5813.jpeg

I am rebuilding my driveline and working on the driveshaft now. In front of the pinion gear is a roller bearing. I don't understand how that bearing is lubricated. Should I install a zerk?
Campbell Tellman
1916 Ford Touring
Beaufort, NC

Anyone know what is the original wood in a 26/7 coil box?

Thanks in advance!
John.

1911-12 TW trade mark front axle with early no oil hole spring perches. $200 plus shipping. kdmks AT att.net.

For Sale are a pair of Bill Bohlan’s Laurel Style Front Lowering Brackets. They are no longer being made.
$250.00 plus shipping Lang’s 1-800-872-7871

Henry Ford acquired A. Y. Malcomson and some smaller investors stock prior to 1907. As a result, he held a significant majority in the company named for him, and for all intents and purposes he was in control.

Here is what he wrote about the six cylinder v. the four cylinder motor at that time.

IMG_4423.jpeg

IMG_4424.jpeg

IMG_4416.jpeg

An original round gas tank. This was stored in dry storage in an attic in the 1960's Very nice no rust out or pin holes. This has the off center drain so it's not an early 12. It had a brass sediment bulb so definitely 12-15, but can be used all the way up to 1920.

$200 plus shipping.
I can ship this very reasonably. I just shipped a 1910 tank...

First Brands appears to be filing for Chapter 11 and state that Autolite is one of
the brands to be discarded. I called around for Autolite 3095 and no one had any
in stock. I was able to order some mail order, but I am wondering what will be
available after those are gone. Just Champion X or do some of you use something
else?

Pretty nice original Ford script tail gate $250 plus shipping. kdmks AT att.net.

FOR SALE: Front Fenders for 1926-7 Model T. One is a New Rootieb Fender and the other is an original. Selling as a PAIR. Asking $900. Contact Gator Gould, AL. PM or email here on the MTFCA Classifieds Website.

Has anyone received the Jan-Feb issue of the Vintage Ford?

Hello, does anyone know what chemicals would you use to clean the wood in a coil box? Basically, what a professional wood worker would use which will not deform or compromise the wood integrity?

Again thanks.

1923 Ford Model T 3-Door Touring Car for sale. Car is complete and running. It has a New gas tank and new carburetor. Also, it has been converted to 12 Volt System with a Distributor. The car is a very good driver and is very presentable as is. The interior is very good and the top is as well. It has side curtains .

Asking $10,500. Serious...

I have a TT chassis with a Ruckstell rear end that needs a new home. I cant take pictures as it is surrounded by too much stuff. The wheels roll but are no good. No sheet metal, body, running boards, engine, lights, steering column or firewall. I would consider delivering to Luray in May if you make a nonrefundable deposit. $1000

SOLD to Ed! Thank you. Nice original pair of burner bases and brass elbows. Good threads. 100.00 including shipping via FedEx Ground within the USA. I don't check messages here but call me at 734-730-4274 or email directly at motoringicons@hotmail.com Thanks and Happy Motoring!

Well, they still exist out there! This one is for sale in Ohura, New Zealand. That happens to be a very small town in an out of the way place, but the dealership still shows signs of what it once was. The town was founded on coal, long shut down, and now supports a small rural population with around 160 residents today. The remains of the railway...

1915/16 Model T Roadster Front Seat Cushion NEW
This is a new, never installed front seat cushion for a 1915/16 Model T Roadster. The material is vinyl. $450 plus shipping. Any questions feel free to send me a msg. Thanks!

IMG_4769.jpeg
IMG_4770.jpeg

Looking at the 26-27 roadster body that just came up in the classifieds,
but
it is in Chippewa Falls, WI and I am in Atascadero, CA (central CA coast 93422),

Any chance someone would be able to transport or know of someone making the trip out west?

This is my dream T since I was a kid hanging out in my grandpa's shop,
I have seen others over the...

I have 6” and 1 7” glass headlight reflectors for sale. $100 each. Plus shipping. kdmks AT att.net.

Looking at the 26-27 roadster body that just came up in the classifieds,
but
it is in Chippewa Falls, WI and I am in Atascadero, CA (central CA coast 93422),

Any chance someone would be able to transport or know of someone making the trip out west?

This is my dream T since I was a kid hanging out in my grandpa's shop,
I have seen others over the...

Looking at the 26-27 roadster body that just came up in the classifieds,
but
it is in Chippewa Falls, WI and I am in Atascadero, CA (central CA coast 93422),

Any chance someone would be able to transport or know of someone making the trip out west?

This is my dream T since I was a kid hanging out in my grandpa's shop,
I have seen others over the...

For sale, 26-7 roadster body with turtledeck, turtledeck floor, gas tank with straps ( nickel size hole in bottom ) No trunk lid. $1700 firm

DSCN2010.JPG DSCN2011.JPG DSCN2013.JPG

Located in No. Illinois, I am hunting for a couple of 30x3 used but drivable tires. White, black, gray it doesn't matter.

Does anyone have a couple collecting dust?

Thanks,
Jim in Oswego

Here is the 3rd major version of the Model T/TT transmission Clutch Drum. Noticeably thicker around perimeter, with only 2 holes, vs. the previous 6. While researching this drum, I have found photos showing the Ford script to be on the front side as well as the back side.

T_725_B2 clutch drum preview_1.jpg

This is first drum used in...

I need to clean up some threads on a 1910 sediment bulb. What is the thread size for the hole where the fuel shut off valve screws into? I know the shut off valves had two different size threads on each side that almost look identical. Thanks!
Mike

I have 4 30X3.5” tires with cracks. 2 Firestone H
And 2 Wards Riverside. The Wards tires are only a couple years old but were cracked all over. Corker and Snyder’s stepped up and replaced them (see pics) very grateful to them both !
I can get pics of the Firestones if needed, but they all have good tread, just cracked and not roadworthy. $20ea and...

I have one pair and 3 other single pieces.
$65 for all of them including shipping to USA 48
Please call or text me at 33zero 3nine one nine zero 62 Thanks Dave

Wood is solid also…$100 including shipping to the 48 states
33zero 3nine one nine zero 62 is the best contact for me, thanks Dave

I have several ring gears, pinion gears a a couple diffs and gears…
Ring gears have a little wear but not much
$80ea including shipping to the 48 states

Pinion gears, 2 are Ford script and one is not.
Good shape. $65ea for the Ford gears and $55 for the other one, including shipping.

2 diffs and one spider. One diff w/ring gear.
Spider, $45...

With or without the distributor is ok but I would like one with the toggle & levers. I'm looking for the type with the distributor on the front, not the magneto on the side.

Located in CA but happy to pay shipping.

IMG_5245.jpeg IMG_4403.jpeg IMG_5302.jpeg IMG_5288.jpeg

Was cleaning up an area in the garage today and came across an old Craftsman hand carry tool box. Opened it up and sat down and went thru it. Going thru the tools in it was like visiting with old friends I had not seen in years. Some of these tools had helped me make a living for years and it was nice to handle them again and put them into another...

This morning while checking the tire pressure I found a screw in my Blockley front tire. I guess it didn't make to the tube as the still had good air pressure and who knows how long its been in there. It renewed my faith in the Blockley tires and tubes. I bought these tires a couple years ago before all the issues with shipping. I'm going to order...

I’ve seen many strange and interesting accessories, but this takes the cake for the silliest. I wonder if one survived?

“Lemuel Bosco of Akron, Ohio, spent $5 for an antitheft device that was supposed to lock the Splitdorf ignition switch of his car, but it didn't stop a thief. He broke it off and took Bosco's Mercer for a joyride. The cops found...

Check this out. Seems like they're made for reaming out triple gear bushings. But just doesn't make sense. Anyone know what they're designed for? Found 'em on eBay, pretty cheap. I already had the Wilson reamer, which I tested, and iit fits inside the fixture bores.
20260307_175852.jpg

20240618_170139.jpg

For sale: hub puller in good condition $50 plus postage
20260107_163458 - Copy.jpg 20260311_190101.jpg

This is a NOS 1914 touring top and rear curtain. It is of vinyl construction. This is brand new never been installed. It was made by Hinson MFG Company in Iowa. They were a large textile mfg company in WWII. They provided interior/tops for Model T's in the 60-70's. These pieces were stored away in climate controlled environment and were never...

IMG_4808.jpeg IMG_4809.jpeg

Need a Jon Brown carbide generator. IMG_5341.jpeg

And a pair of Rands windshield hinges. IMG_5346.jpeg

Side and tail light burners , $10 each. Burners with no hoods, $3 each. Your choice, plus shipping. kdmks AT att.net.

For sale is a reproduction Monocle Windshield Frame with steering column mounting bracket. These castings have had minimal machining of the mounting holes, and could be polished if desired. $95.00 plus shipping. Lang’s 1-800-872-7871

I have a 22 touring and I put it away last fall. We pulled it out and it would not start. To cut to the chase; cleaned carb twice, charged battery several times, sprayed a little starting fluid, put oil in the cylinders, and finally restored to pull starting. It fired up immediately and ran beautifully. Put several miles on it, filled fuel tank...

IMG_8587.jpeg I just got the head back the machine shop this week. The head got 8 new valves, 2 new valve guides and 6 bronze inserts. There is a serial number on the front of the head and it is 1077 X. There is freeze plug on the top of the head that has some number but are pretty hard to read
Fitz

We need a complete coil box lid with unbroken side clamps for a 1926-27 engine-mounted coil box. An original one is preferred over a repo. Thanks!
Marshall (563) 322-1319

Hello all !! Are the ring and pinion gears the same between the small drum and the large drum
Thanks

Thes are original Model T Ford side lamp brackets.Singles except for # 6. The use is based upon what I beleive. You are the judge of the use of them. All are steel originals. The price includes shipping to lower 48.

#1 1923-25 $40
#2 1915-17 couplet, scarce $110
#3 1909-10 tail light (perhaps to 1912) $60
#4 1915-17 center door $45
#5 various...

I have 3 - nice 26-7 coilboxes with covers, $115 plus shipping, 26-7 engine blocks $350 plus shipping, 26-7 rear axle housings
$100 plus shipping, 2-3 High radiators $150 each plus shipping. 26-7 frames excellant condition $350 each. All items can be picked up in Ct 06013. Email needs with contact# I will call you back to discuss all items and...

I have a great start on a 1914 WW1 Ambulance Body and Chassis, 85 % finished but all materials are there to finish this neat
piece of U S History. Located in Ct 06013 25 miles from Hartford. I can Deliver within a 100 mile radius for fuel. Asking $4,500 Email for pictures and send Contact# to discuss the project. You will not be disappointed with...

Torpedo front view.png

3 slightly different headlight door spinnings for 1913-14 head lights, $20 each. 7 brass rims for 1915 headlights, $20 each. Plus shipping. kdmks AT att.net.

After repairing the horn switch & reworking the horn on a '23, I've come to find the horn needs a bit of work. What exactly does the adjusting screw do?

4 bezels, 2 back and 2 doors for John Brown model 15 and 19. $125 for all. 1 door and 2 backs for E and J 466 headlights $40 for all plus shipping. kdmks AT att.net.

Wanted: original 1914 Ford coil box lid

I purchased a new repro lid for my 1914 T awhile back. When I installed the coils, the lid would not close all the way. Now I have to drive with the coil box lid off. I am using original metal top coils. I set the metal top coils along side of a later ford coil and the metal top coil is much taller then the...

Set of flywheels magnets. They have some very light surface rust. Good for cores. Will need to be remagnetized. Never hurts to have a spare set on hand.

$25 plus shipping in the U.S.

IMG_9348.jpeg

IMG_9347.jpeg

Brass Ford script. Measures about 7.5”x3.5”. Could use a good polishing.

$20 plus shipping in the U.S.

IMG_9350.jpeg

Heavy Case Muncie - Gears look very, very good with exception of underdrive gear on lower shaft, which has 4-5 teeth in a row damaged. Photo of damage included. Everything spins nice. Under-Direct-Over-Reverse. Roughly 2:1 U, 1:1 D, and 0.73:1 O. Were used in Ts and TTs. I don't have the couplers. Pick up south of Kansas City or can deliver to...

To continue along with this series, here is the 2nd major series, the T-725-B.1 (first B version). This one has the 6 holes around perimeter, and the first to use the set-screw. The front thrust face is designed to be used in conjunction with T-769 (top hat) bronze bushing. The set-screw to thrust face is the noted .530 - .533 . Nothing on parts...

'Looking for a good pair of front top bow clamps with thumbscrews for a 1926-27 Touring. I don't know if earlier clamps will work, but I suspect they will. Thanks!
Marshall (563) 322-1319

Hello everyone,

As some of you have already heard, I committed to obtaining several key Model T parts drawings from Benson Ford Archives. The purpose is for my ongoing 3D and schematic drawings to use a an educational tool for both here on the forum and for collectors.

A lot of the problem in rebuilding the transmission seems to be...

Interesting early Union Forge counter weighted crank on eBay. You can tell because of the “patent applied for” and the forge stamp of a “U” in a circle

IMG_7675.jpeg

I don't know how many times I have seen a what it's worth post but I'm in need of a answer. I have a For sale Vehicles ad for my 1925 Model T
Fire truck & have had 0 interest in it as of yet. I'm wanting to know what is the issue with it & what someone would be willing to pay for it?
Is there no interest in it, is it too high priced or are T's...

Hello forum. I’m on the lookout for an electric horn for my TT. Preferably a Klaxxon or such. Show me what you got.

Thanks in advance, Jacob Mangold

Converted File.jpg
This was made from picture of the wrench, creating a cad file and sent to a 3D printer shop and printed out of stainless steel for ~$120 . All I know for certain is the hub cap end of the wrench fits and I have pressed pins into the spanner pin holes. I haven't a clue what the rest of the wrench is supposed to fit thus I...

IMG_5243.jpeg IMG_4866.jpeg IMG_5147.png IMG_5140.jpeg

For sale: bottom of carb $25 plus postage

20220730_140333.jpg

Thought this would be of interest. Says it can be construction from the diagram. Safe to assume assume that the 1 x 2 lumber is exactly 1 x2 back in the day

Early style front engine mount used from 1909 to about 1921. Nice condition, u bolts are in great shape with excellent threads. Can be hard to find these u bolts that have good threads.

$50 plus shipping in the U.S.

IMG_9268.jpeg

IMG_9269.jpeg

IMG_9270.jpeg

Wire wheel rear hub. Has some pitting, but the taper and keyway looks to be ok.

SOLD! $50 plus shipping in the U.S.

IMG_9264.jpeg

IMG_9265.jpeg

IMG_9266.jpeg

Just a reminder that the annual old car swap meet in Marrietta, Ohio is Sat March 7th starting at 7:00 am. Lots of vendors with lots of model T and A stuff. Nice heated building with a nice lunch and pies and hot coffee. Vendors in attendance include Kevin Prus, David Nolting, Ron’s Machine Shop, The Carb Shed, The Coil Dr., with many individuals...

One more item, a period Water Pump looks to be serviceable $50 plus shipping, again contact via text or call, 3threezer02fourone2six4one. Thanks Wingnut

i set the body on the frame the other night and used 1/2 inch bolts to secure to the 6 frame mounts and everything seemed to line up but I see the front fourdoors seem to be above the firewall so I'm guessing the firewall was not raised up to where it should be. My question is am i overlooking something as when i picked up the car the firewall was...

One hundred years ago in March of 1926, My Model T coupe rolled off the assembly line. When it was 44 years old in 1970, 56 years ago I bought it for $600.00 and began restoring it when I was 16 completing it 2 years later when I was 18. I am now 72. Jim Patrick

IMG_6603.jpeg IMG_6602.jpeg IMG_1257.jpeg IMG_6606.jpeg

For sale: Brass Kingston L 1916 carb $350 plus postage
20220806_105131.jpg 20220806_105259.jpg

For sale: steering wheel spider $25 plus postage
16 inch 1920-1925
20230222_094214.jpg

Transmission driven gear puller. Broke on pulling off a very stubborn repro driven gear. Worked like a champ before. Cost is zero. You pay Priority postage. Email me via the website.
Richard Gould
20260307_104327.jpg
20260307_104201.jpg

I am working on the chassis that I pulled out the the ground/weeds at my late friend's house have am nearly ready to finally start the engine after quite a bit of work getting it unstuck and cleaned up inside and out. It still looks pretty ugly and rusty which I kind of like and I was fixing to order plug wires and a timer wiring harness but...

YEEEEEOOOWWW!!!

This is a nice pair of hard to find Firestone 30x3.5 demountable clincher rims. No heavy pitting, just some light surface rust. The clincher edges are in very nice shape. I wouldn’t be surprised if these have never been used.

Price drop!
$100 for the pair plus shipping in the U.S.

IMG_9107.jpeg

IMG_9109.jpeg

IMG_9111.jpeg

IMG_9113.jpeg

Looking for a burner base/stand and gas elbow/supply like the one in the picture.
Thanks!

Screenshot 2026-03-05 at 9.43.07 PM.png
s-l1600-2.jpg

20241028_161152.jpg
For sale: Rayfield carb and intake manifold $250 plus postage
20241028_161120.jpg 20241028_161051.jpg 20241028_161120.jpg

Free: Three rusty side and tail lamp bodies. One tail lamp is pretty beat up, the other is just plain rusty. The side light body has a lot of surface rust but you might actually be able to bring it back. They're free just pay shipping. I would prefer to get rid of all of them at once.

ttlb03.jpg

ttlb02.jpg

ttlb01.jpg

Thanks for looking!

Free: I still have a whole bunch of Truss Head (or mushroom head or brazier head) rivets, with a 3/16 x 1 shank, made of what I'm pretty sure is mild steel. Some surface rust is present but they should clean up pretty easily. I believe these would be well-suited for riveting wood slats to a steel frame, as you would on a pickup bed or depot hack...

Sold to George! This large Rubes 3/4 twist horn is about 10 tall and is about 6 wide. This is the style with the large bell and rim. It can be used on a right or left-hand early automobile. The original tubing is about 40 long. It's in great condition. Complete with the thumb nuts, screen, adapters, reed, etc. Honks well. The rubber bulb is...

Sold.........

I have 3 Stromberg OF's for sale. Selling to fund additional projects.
1. Fully restored (on mounting stand) looks to have all new steel parts. Excellent Condition. $650 includes shipping lower 48.
2. Excellent condition may have been previously restored? Throttle linkage not original, I believe replacement parts are avaiable,100% clean...