MTFCA Forum

Ford script Model T Jacks. Take your pick $35 each plus $18.50 domestic shipping. Mark Chaffin (951) 805-0928

20240918_101250.jpg

I recently, against my better judgement, purchased a pre/1919 engine that had been sitting outside for decades. I was hoping to at least get a spare hogshead out of it but no luck. I cracked it. Crankcase was packed full of dirt. Out of curiosity I hosed it out and pulled the #2 main cap off. The journal was decent 😳 I decided to press on. But I...

The '15 Ghost has a pair of mystery holes drilled into the metal trim piece just below the windshield, where something was mounted over a hundred years ago.

They're 3 3/4 apart and approximately 5/16 in diameter on the right hand side of the car. No sign of wear or use since the car was restored in the sixties, so they presumably predate that....

One set of manifold clamps with the correct domed bolts for the improved Ford (26/27). Price is $30 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20240918_140202 (1).jpg

I am making to take the T in the mountains for camping. This would involve going up continuous grades of more than 6% for many miles. And certainly, I would need to go above 10% grade in some sections. A friend of mine agreed in the sanity of this idea and suggested that I get an outside oil line installed. I have no excuse with a inventory of...

Greetings Friends:

I'm a little ways into the delayed rebuild of the motor for my '23 touring car. I wanted to use the same crankshaft (it's still standard, incredibly), but my machinist just called to tell me that it failed the magnaflux test. Uh-oh.

So, now I'm in search of a good crankshaft. Anybody have one to spare? I'd be grateful to...

Today I decided the clean up the rear outer wheel bearing and fit new seals on my 27 Coupe.

Left hand side leaks a bit but the right side doesn't so I tackled the right side first.

I have a set of Neoprene inner seals on hand so I pulled the hub off and dug in.

Once I got the sleeve out I discovered there seemed to be no inner neoprene or felt...

Complete Dodge Brothers front end, marked axle and spindles, has tie rod and drag link. $900 plus freight or can deliver to Hershey. Larry Debaugh

Pending!
$20 for the pair/set INCLUSIVE of domestic USPS Shipping.
20240916_111110.jpg

I'm about to venture into my first T Transmission and after watching a few videos I don't think I have the appropriate puller for removing the Clutch Basket if it is stuck on.
Beside buying a new one from a vendor what other options do I have?

Found these in a box of Model T parts at a recent estate sale. Although not Model T parts, they are from the era and very collectable. Description and prices are as indicated below.

20240918_090007.jpg
Hubley Trick Dog Bank. It works as it should. Full of coins. Missing key. Price is $100 plus domestic shipping. SOLD

20240918_090046.jpg...

Three Tillotson carburetors for rebuilding. These work great on a speedster! Get all three for $45 plus $18.50 domestic shipping. Mark Chaffin (951) 805-0928 SOLD

20240918_093438.jpg

Actually the whole rear end. Two-piece driveshaft, forged end radius rods, 13 -14 rear end,, Chicago duplex cantilever spring assiste. Richmond is coming, I'm in mt.vernon Indiana. Come load your truck. 800.00 for driveshaft alone. If you take it all( minus wheels) the price is 1250.00. ctleonard64@gmail.com IMG_20240524_150239587.jpg...

Why strangle your car with modern INCORRECTLY MADE float valves
standard vs full flow.jpg

Do my valves work? Ask the guy who just passed you on that last long hill...
Full Flow Float Valves in Process.jpg Full Flow Float Valves.gif

For info EMAIL ME DIRECTLY

I don't monitor ads closely particularly after it sinks out of view, so EMAIL ME...

Needs restoration, As pictured, $20 INCLUDING continental US domestic shipping 20240916_141657.jpg
20240916_141743.jpg 20240916_141647.jpg

An assortment of Ton Truck stake bed brackets $35 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928 SOLD

20240918_083142.jpg

benautos.2.jpg

Hello everyone, :D

I would like to introduce you to a video made by a young French YouTuber, Benjamin, creator of the channel Benautos, about the legendary Ford T.

Benjamin conducts numerous reviews of classic cars in France, attracting a mostly young audience. Recently, he has become increasingly interested in pre-war...

Got these from a recent estate sale. SHELDON Spring Protectors. Great for display or use. There are nine sets. Get the entire lot for $25.00 plus $18.50 Domestic USPO Flat Rate shipping. Mark Chaffin (951) 805-0928 SOLD

20240918_084705.jpg

20240918_084653.jpg

Pan support bracket set $25 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20240918_094056.jpg

Front motor mount complete (26/27) $25 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20240918_093938.jpg

One set of late style front fender irons. Price is $30 for the pair plus domestic shipping. Mark Chaffin (951) 805-0928

20240918_101422 (1).jpg

One 11 tooth pinion in very good condition $75 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928 SOLD

20240830_112405.jpg

Assortment of NOS parts as indicated below. Mark Chaffin (951) 805-0928

20240917_121848.jpg
Three drag links for tapered ball, one opposite end threaded, one straight shoulder ball. Get the entire lot for $60 with free domestic shipping.

20240917_121903.jpg
10 Tooth Pinion NOS $100 with free domestic shipping.

20240917_122721.jpg
26/27...

12.jpg
13.jpg
14.jpg
15.jpg
16.jpg
I found this in my transmission screen. I am assuming I am going to have to
pull the engine and repair the tranny.
What gear did it come from?

Has anybody seen an accessory amp meter and switch like this that mounted onthe steering colum?g IMG_2269.jpeg IMG_2267.jpeg IMG_2270.jpeg

W went on a 3 day and 2-night camp trip with the T. It was back in late spring/early summer. I forgot to post it till now ... We went to School House Falls in the Ozark National Forest on the old CCC Wilderness Trail west of where we live. Did a little hiking, some Dutch Oven campfire cooking, cooked on our 1926 Montgomery Wards gasoline stove,...

Yep...2 days ago that day tour, today it was our club member Doug Galloway again hosting a fly-n-drive in good time at his rural airport. He has several Ts and flies. I just have T's! :lol:

It had over 40 planes this year plus 6 model Ts & our Prez's '40 coupe. I gave 6 or 7 rides to various bunches of people in my '13 touring, of all ages, lots...

These photos were sent to me by a relative asking if I knew what the heck it was. I said I’d ask here. It looks like it converts a non demountable to a demountable rim. We were speculating that it might be used for a quick change for a flat but that’s just a wild guess. Anyone got any info on it?

Hello all,

For the past 10+ years I have been using a popular classic car company to insure my vehicles. I don't want to name the company in this post, but suspect most of you are familiar with the insurance provider.

Unfortunately I had my first claim after a driver ran a stop sign and t-boned my classic Jeep. I suspect my Jeep is totaled due...

I am getting close to the point where the rear axle is ready to go in so I am looking at other parts that need to be in place. I have a nice Muncie that I am using in this car. I have the proper connectors and the support, but I don’t have the hardware for mounting the support. The manual shows a couple of “U” bolts that go over the top of the...

I used to go to this meet when it was operated by another organization. That was over 10 years ago. Has anyone gone in recent years?
If so, is it worth it for T stuff. Pictures suggest mainly 50's on.

I'm thinking of going but don't want to waste my time if there is very little T stuff.

Thanks,

Greg

Last Sunday I drove my ‘15 touring to the hardware store, about a 10-mile round trip. Coming up a hill in Ruckstell low, Ford high about 50 feet from my driveway there was a loud bang and a sharp jolt, then the back wheels locked up, the engine died and the car skidded to a stop, leaving two skid marks. It all happened very quickly. Being stopped...

Offering a reflector and spring for free. Buyer just pays shipping or free pickup in Burbank, CA. Just trying to clear out some space and would rather not see old parts go in the trash.
PXL_20240917_221652874.jpg

If anyone has a set of Leon Parker’s plans for a 1924 Touring, I need a set. Either an original full set or full-size photocopies.

Some time ago I found reference to a new body for a Model T which had become available in 1919. The design if thats what one would call it if nothing else is different'. The Australian news paper the report was in was as always the case never mentioned any actual details only saying There is now in business of disguising the Ford in the United...

Where are the national tours going to be for both the MTFCA and MTFCI in 2025?

I am located in California. Willing to pick up locally if necessary. Looking for a 1926 Steering Gear Case/Cup. If it comes with cover, I am happy to purchase as set. Thank you. Lisa - lirogo27@aol.com

Today I got ambitious and drove my 3 cars into the RV parking lot so I could photograph them together. They show advances from 1916 to 1936 to 2007. The Packard is quite a bit larger than the Model T or the Mercedes Benz SL 550. They are also quite different from each other to drive.
Even with the two outside mirrors and one inside it is difficult...

Got a question on the 1911 Engine Block....are the Intake and Exhaust ports on the side of the block threaded for some sort of insert between the manifold and the block?

Also, on the 1911 Block is the oil fill a long tube running down the left side of the engine like on the 1909's?

So, if any of you guys has a 1911 block, disassembled or...

FS: Early to Mid 1926 Rear Crossmember, used junkyard part. This one is in pretty good shape, no major pitting issues, only the spring bolt hole is slightly wallowed. This is the early 26 one without the flange. Asking $40 not including shipping.

t26rrx02.jpg

t26rrx01.jpg

t26rr04.jpg

t26rr03.jpg

Thanks for looking!

I have a new, unfinished firewall of the 1911/1912 two piece variety. I plan to stain it using Laurel Mountain cherry stain. For those of you who have done this staining, how much stain is needed? Since front and back need staining, it seems like it would take a whole lot more than one of the 4 oz. containers that Laurel Mountain sells.

I have newly acquired 1915 Centerdoor with AC Brakes, which I know nothing about.
How do I adjust them?
Thanks,
Dave

I am looking to make a new run of Upper Tapered Reamers and Lower Reamer/Taps for the Stevens Front Axle tool. Jack is making a new run of the frames, so I thought I would make some more tooling. You can’t use the frame without the tooling.
I am needing 12 people to commit to buying a set for this to happen. Price will be $525 each set +...

1926 Model T Ford Engine. With Matching Title.
Equipped with a very nice Frontenac head, Exhaust Manifold, Original Frontenac Valve cover and Stromberg Carb. This engine comes with a current Missouri title that matches the engine block. I have had this engine running in a car earlier this year. Video of engine running and additional photos...

Looking for any information this Kwikway Multipurpose Machine. It will grind valves but looks like it can also be setup to undercut armitures and who knows what else.
Not exactly Model T, however it will be used to grind Model T valves.
Any help greatly appreciated, Thanks in advance,
Kevin

Want to buy 26-27 Ford accessory Canadian rear bumpers, the split bumperetts. Can pick up at Hershey.
Can Bump.jpg

I am in the process of restoring my Ruckstell rear end. I had to replace many parts including the axle shafts. Now I tried to install the left (the Ruckstell) axle housing to the axle shaft. This did not work as the diameter of the modern axle bearing in the axle housing is smaller than the diameter of the axle shaft. When I tried to do that, I...

Time again for Lang's Old Car Parts Calendar! Lang's Old Car Parts is accepting photos of your Model T for our annual calendar. Photos and information are due by Friday October 14th! High quality photos only (photos from phones usually do not work). When sending the photo, make sure it is downloaded in FULL SIZE. Newer phones can take good enough...

Over the years I think I've probably tried all the available radiator flushes. Even CLR, but now the instructions on CLR say not for cooling systems. What is the best one for a Model T?

Two gas headlamp burners NOS. Unobtanium. Price for the pair is $100 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928 SOLD

20240916_141332 (1).jpg

One very nice transmission drive plate with very minimal wear and tight rivits. This is for the narrow drum transmission (09-25). Tail shaft is 1.559. Stock is 1.560.
Price is $125 with free domestic shipping. Mark Chaffin (951) 805-0928

20240917_115232.jpg

20240917_115258.jpg

20240917_115318.jpg

2 different kinds of oil pan support brackets. $125.00 for each plus shipping. kdmks AT att.net.

IMG_5678.jpeg IMG_5719.jpeg -
Just want to let you all know what we are up to out here on the west coast.

About a dozen Ts and 30 of us from the Redwood Empire Model T Club toured in and around Virginia City, high in the Nevada mountains, for 3 magnificent days last weekend. All of our meals with the exception of our final banquet were cooked and...

FS: two Stromberg OF carburetor bodies with various parts missing or damaged. One early style OF is mostly complete but the needle valves are badly bent and will probably need to be replaced. The other is basically just the body with a few parts still left in place but it's probably salvageable with some work. This project is probably best left...

Helping a friend with a new purchase. TT and it has a Jumbo ppoverdrive. Seems to function properly. Need to change fluid. Not sure how full to fill and what oil. 600 W, 80/90 or ??? Anyone have one and could give some advise. Thanks

Looking for a Splitdorf model D magneto distributor cover/cap like in the photos. The mag I have it is missing it.

Thanks!

This professionally restored Tail light has been in our display case since the early 1990's. It's in like new condition and ready to mount on your T. Asking $325 plus postage. You would be hard pressed to find a nicer one!
STOP light 1.jpg STOP light 2.jpg

Please use this email address below and NOT the personal messaging system to contact me....

Here is a water pump in my stuff. Has name on it but hard to read. Looks like one ear has been brazed on. $45 + shipping. Email me at address in pictures. Thanks Dan
IMG_4024.jpeg
IMG_4023.jpeg
IMG_0260.jpeg

IMG_8085.jpeg IMG_8063.jpeg IMG_8064.jpeg IMG_8065.jpeg

Does anyone have any info on Strong Hold small drum brakes? Jim

Sure is getting crowded in the shop these days…

IMG_2597.jpeg

I am in the search for a 26-7 gas tank, I have never followed them so do not know what to expect to pay for one? Thanks Joe

Looking for 26 27 tudor sedan front seat frames any help is appreciated

For sale a new 6 volt Mitsubishi alternator!
Catalog price is$259+ tax and shipping
Mine is $200 plus shipping
Pm me if interested

Want to buy 1 upholstery end cap pictured below for a roadster body that I am trying to keep all original sheet metal on. Thanks, AJ Eyre.

Chuck.jpg

I've had a few requests for my KC Warford support brackets, so I'm making some now. These are bolt on with no drilling, and are designed for the KC Warford. They will work with an original aluminum Warford as well with a minor modification; just let me know in advance and I can make the adjustment. This supports the rear end of the Warford, and...

Nice spring perch set with good threads $40.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928 SOLD

20240618_095419.jpg

Kellogg in line tire pump gauge, Schrader tire pump filler ends one with lock and one without, Tire tube stem 4 in one and three in one tools, and four metal valve stem caps. Asking $30 for the lot plus postage.
I.jpg
Please use this email address below and NOT the personal messaging system to contact me.
email.jpg

Accessory oiler set for the three dip pan $30.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20240620_100309.jpg

One steering pitman arm in very good condition $35.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20240618_095303.jpg

Rear axle differential complete in very good condition. Why go to the effort and expense of tearing apart many rear axles in hopes of finding a good differential. This one is ready to go! Price is $175 plus domestic shipping. Mark Chaffin (951) 805-0928 SOLD

20240916_124446.jpg

20240916_124515.jpg

20240916_124733.jpg

Gas tank bracket set for the oval gas tank $30.00 plus domestic shipping. Mark Chaffin (951) 805-0928

20240718_133623.jpg

One early front motor mount $50.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20240819_141601.jpg

I,m looking at a 1927 model T roadster that has no top. I wondering what are the chances of finding a complete top for this car? I hope to find something close to the Portland area. Tom 50three 644-937four

If you have a Ford manufactured prior to 1916, be sure to use a jamb nut for the adjustable ends. I just ran across one from one of my cars, where the throttle adjustment is barely holding on.

I have a project in mind that could use one of these. Has anyone got a spare to sell?

Paul

Use this as a lesson how to terminate an ad WITHOUT BUMPING EVERYONE ELSE'S STUFF DOWN THE LIST.

Junk carb - not reasonably a rebuild candidate...it is a donor carb

no float cover nut
no float
no float valve needle
no choke wire securing screw
modified mixture needle
pictures are the best description

despite the obvious problems, there remain a...

WTB one rebuilt wood coil or one that just needs a cap. In Wisconsin. Thanks

4 Wood Felloe Model T wheels- Good Condition, clincher edges straight, takes 30X3 tire and tube, wheel plate plain, $600 or make offer jferguson27@austin.rr.com 100_3301.JPG 100_3298.JPG 100_3299.JPG

This photo has appeared on ebay, it shows women and men working on Model T's at what appears to be an emergency assembly line during or after the first world war.
Any one have an idea as to what is the story beind this? Possibly Model T Ford ambulances being rescued for reuse, what country might the soldiers be from?

I have recently acquired the tools and machinery to pour and size babbit, I am not professing to be an expert by any means.
However I have made some observations, it seems that the older engines I have disassembled which appear to have OEM Babbitt. I only “assume” these to be OEM, for example they would typically have cast iron pistons....

My car has mirrors mounted to the upper door hinges. They seem useless, I can barely focus them and they dont keep the setting after a few miles due to vibration. Are they a silly add-on or would they be more effective mounted on the center hinge posts? If I want to remove them would I just replace with a standard pin?
The car has a wide rear view...

Howdy,
Seeing clutch springs advertised in classified section brings a question to mind. What is the compression rate (lbs) in one inch?
Thank you

Looking to buy 26 27 tudor driver seat frame any help is appreciated

6V Hutchins A-OOO-GAH horn. Needs restoration I tested this on a battery and while the motor does spin, it does not make the horn sound. $40 plus shipping or pickup in Burbank, CA
PXL_20240914_224028244.jpg PXL_20240914_224022421.jpg PXL_20240914_224016841.jpg PXL_20240914_224007098.jpg

IMG_5445.png

One set of rear shock absorbers that have been identified as Steelbilt brand ( per this thread on the forum ). Most of the key pieces are there, though we are missing one of the bars with the two loops, though this shouldn't be too difficult to fabricate. Based on the pictures in the thread, it also appears that the existing bar may be misshapen,...

I received the below assemblies in a box full of T parts from the widow of a T owner, but I'm having trouble identifying them. My first thought was that they are some sort of shock absorber, but I've not been able to find a match online. There is also a possibility that they are not a T part at all. Has anyone seen these before? Any help would be...

A friend of mine who is new to Model T-s could benefit from Milt Webbs book………I can’t find one on EBay for him…..Thanks!

The title is a bit of a misnomer since it was 3 days. We met in Virginia City, Nevada. We traveled to Carson City for a day, Reno to the National Auto Museum then a day of trains and the historic town. 11 cars and 24 people had a great time.

Andy
D88FF374-D8CA-4DEF-B5E4-346D3F282997.jpeg
The hundred mile view...

I just bought a Marquette tool to attempt to change my tires (since I ticked off ever tire place in town because of these clinchers). I wanted to ask if anyone has any literature or just pictures or a video of exactly how it is supposed to be used. Also, I saw a video once of a man mounting clincher tires on some English car. He placed a thin...

Nice original January 1914 sales catalog. Has a water stain in lower corner. It has the notice of speedometers being available. $100 plus $10 shipping. kdmks AT .att.net.

I think Robbie Price has used it. IMG_5465.png

Need to be tested.

Lenses are in great condition and are three inches in diameter. One is in primmer. Asking $55 for the pair plus small flat rate postage.
DORAY CATAPHOTE - 260 CATEYE REFLECTOR SET front.jpg DORAY CATAPHOTE - 260 CATEYE REFLECTOR SET back.jpg

Please use this email address below and NOT the personal messaging system to contact me.
email.jpg