MTFCA Forum

I need to install a new fan on my 1919 roadster due to .metal fatigue and hairline cracks. I have the new blades and rivets and have already removed the old blades by grinding the heads off the old rivets and punching them through. Now, I'm faced with installing the new rivets. Is there a special rivet punch I need, or do I just wallop the bejesus...

It should fit, but the inlet is 2 inches, so you have to enlarge, not reduce, the connection with the exhaust pipe.
Do they make a 1 1/2 inch to 2 inch adapter that would fit or do you have to have it made?
Exhaust parts are always measured by ID and OD, so it makes it hard to find a piece that fits.

Left side. No burner. Cracked square glass $125 + USPS Medium flat rate
gwhouse731(at)gmail(dot)com

I don't believe anyone has really said anything (-or posted any pictures) about this year's tour. To somewhat keep this Model-T related, there were a handful of Ts participating. I think there were 52 of us that started the event, -and I think there were approximately 7 that failed to complete the tour under their own power. None of which were...

We are currently stationed in Bradenton (Manatee County) where we will be waiting out the storm. Jim Cantore is staying at a hotel here in Bradenton and there is a fair chance we will go thru the eye. The boat (65' Bluewater) I do work on, not mine is tied up at the marina down the street in Sarasota (Sarasota county) at the primary marina. I...

I am learning to drive my model t and have a couple of questions.

1. My model t as with many t’s wants to run forward when cranking. I’ve jacked it up or put wheel chokes in place to keep that from happening. Can the car be started with the parking/emergency brake engaged.

2. I have big feet so operating one lever and three pedals in a tight...

IMG_7619.jpeg IMG_7713.jpeg IMG_7720.jpeg IMG_8753.jpeg

Finally getting around to advertising my Frontenac single overhead Cam race car. If you want to really go fast you can't beat a single overhead cam Frontenac powered machine for speed....... and finishing a race. Faaasssst and ready to race, $25,000.00. More pictures on request.

Ed aka #4

Anybody have the two hole type?

Thanks,
Michael

I am selling our 1915 Touring car due to inability to figure out how to drive it without killing myself and everyone who's in it with me. Actually, two knee replacements and big feet are the problem. The car is in our garage in Upland Ca. It's an amazing car. Rajo head. model A crank, custom header, completely rebuilt 1926 engine and trans by Eric...

need room

1908 Model S Roadster. Complete car, Canadian Built, work in progress, not running. New body with original seat section. Buggy rails and useable top. New gear case by Floyd, new exhaust and water outlet manifolds. Aluminum pistons and new valves. Rebuilt Heinze coil box and four good coils. New smooth all gray tires, tubes, flaps....

Need the room

1922 Coupe. Ricardo head, OF carb, hasslers, ruckstell, AC brakes, I Timer. New tires, tubes, flaps, top, upholstery, radiator, safety glass. Matching 1922 Washington plates and clear Washington title in my name. Featured March car in Lang's 2024 calander. $18,500. More pictured on request. Located in Friday Harbor on San Juan...

I wonder if it’s possible to tow a Model T in neutral please ?

It will be going less than one mile to my local garage for final inspection and adjustments before I hit the road !!

Thanks from a newbie in New Zealand 🤗

Here you can view a short video depicting the camping setup:

Longing for Adventure and Learning from the Sages
The acquisition of a motor car transforms transportation from mere practicality into a splendid gateway for adventure. Having primarily utilized my Model T Ford for quotidian errands, I found myself inspired by the delightful...

For sale 1914 Model T Ford touring car, engine casting date 2-20-2014. The car runs and drives well after being revived from 25 years of storage in 2017. Mechanical components have been checked and refreshed including the following: new tires, Brassworks flat tube radiator, rebuilt Holley G carburetor, rebuilt coils, TW timer and more.
The...

I don't know if I am thinking things that didn't happen or what but I am wanting to replace the bakelite parts in a horn button that clamps the steering column and I think I bought the parts from a vendor at some point in history but now all I can find is complete units. Are the repair parts no longer available separate? This the button and the...

Well, it's back on the market. Hard to believe how many serious tire kickers are out there leading us down a path and then just fading away! And I won't mention any names. So anyone that was thoroughly disappointed for missing out, you now have a second chance. This could vie for the finest restored Model T Ford Torpedo Roadster in the world....

This car belongs to an acquaintances of mine that inherited it from their father. I have not seen this car in person, nor heard it run. It is located in Kalispell, Montana and has been in good, clean, dry heated storage. The engine # 6142472(1922). I believe based on who the previous owner before Mike was and the fact that Mike owned an aviation...

The door latch on my 14 isn’t original to the car. Either it is a rear door latch (don’t know what they look like) or they made 2 different styles with the handle placement slightly different than the other. I was thankful to purchase this interior from Mr Art Ebeling here in the forum and I have a picture of his latch with the handle clearly...

… I didn’t :oops: The foam crap needs to be replaced occasionally. I haven’t driven the roadster since the 2019 Covered Bridges tour where it performed flawlessly. So the other day I figured I’d wash off the dust. Air the tires and pour 2 gallons into the gas tank. Also serviced the radiator. Primed her 3 times with ignition off and she started...

When did Ford change the design of the grease cups from the early style to the later style used until the end?

brake pulls.jpg brake pulls 1.jpg brake pulls 2.jpg brake pulls 3.jpg

Didn’t someone make a reproduction of that handle…….I have 2 Buckeye jacks…..one handle is rectangular on the end, one is round.

Every time while driving my grease cap on the fan hub untwists and falls off. No matter how tight I twist it on it is missing after a tour. How can I keep it on ?

The cork gasket from the vendors leaks too much. It is destroying the paint on my tank.
If there is a neoprene one out there I am willing to try it.

Took the Grands to town for harvest festivities, followed by a car show in the afternoon, and ended the day at the winery with balloons! 20241005_183032.jpg
20241005_175548.jpg
20241005_183025.jpg

So on my 1919 runabout, the fan has seized for the second time in the span of 15 miles worth of engine run time. I’ve found that it does free up if I loosen the center shaft but I’d prefer to not have to fix it every 15 miles. Is there something I’m doing wrong, the fan spins freely when I put it on and then locks up and melts the belt before I...

I love my enclosed trailer for hauling my cars. However, towing a trailer is like pulling a great big box and I can't see anything behind me!

trailer corner.jpg

I would love to get a wireless back up camera to be able to see behind while backing up and as a rear view mirror.

My thought was to wire the camera to the license plate light,...

I'm looking for a steering wheel for my 1926 speedster project as used on racing cars at the time. 4 flat spokes with a hub to fit the Model T steering shaft. Wooden rim preferred. I can purchase and pick up at Hershey.

I know it's a long shot but I thought I would try and see if somethings available.

Thanks,
Gene
Union Bridge, Md.

For the 21st year we will have our free swap meet at the Cameron farm, 5894 Lemond Rd in Owatonna, Minnesota. Ribs will be served as always ($10.00 donation for lunch please). Everyone’s a vendor or no lunch for you! Indoor heated spaces available. See you there…..

Just for everyone’s info. I shipped some parts yesterday & USPS started their Holliday rates. A medium flat rate box is now $19.30 & a large is
$26.00 I didn’t know Halloween was a big shipping time? :o
Craig.

Well, they were in one of the boxes.
Neat turn signal switch $35 plus shipping pending
No idea about the Halogen kit might be for Model A $15 plus shipping
Dip stick with instructions $50 plus shipping
Pair of Hood handles steel T-4051HC $22 plus hipping Pending
Fuel pump 12v 2-4 lbs $68 plus shipping SOLD
Texas T carburetor with air filter $40...

My rear wheel puller is on backorder till November, is there a creative way to nondestructively remove my rear wheel? My left parking brake gets bound up randomly somehow. I tried spraying brake cleaner in the vent slots and around the drum gap to clean it out, until the cleaner came out clean. Lubed the rod shaft. Wheel spun like butter but then...

Does anyone have any info on Strong Hold small drum brakes? Jim

New Field Coil 5107 $50.00 + shipping.
Check, cash in a birthday card, Zelle, PayPal F&F.
kampfdackel85(at)yahoo(period)com
8049#5593#96 txt, call, email. 5107 starter field coil.jpg sfcside1.jpg sfcside2.jpg sfctop.jpg

Looking for 2 rear wire wheel hubs for. 1926. Would rather use wire wheel hubs vs. adaptors. These are model T wheels, not model A wheels.

Nice 26-27 wire wheels hub and drum. Hub is very clean with some original paint. Drum is rusted but sand blasting should clean it up.
$150 plus shipping. Neil

According to the AACA forum it was a hot time for opening day in Green field today.
Someone had their camper burn to the ground. Hope it wasn’t one of our guys. And hope no one was hurt.
Looks like luck it was opening day cause no one was parked close to it.

Hhowdy, Can anyone tell me if a early (up to 21) lower steering column to frame mnt is the same as the later with the exception of the number and size of the bushings. It seems like my 26 roadster is always in need of that bushing replacement and I am thinking that maybe the earlier mount with twice as much bushing surface would last longer, any...

I have a friend who is looking to buy a starter equipped Touring. He'd prefer something within 5-7 hours of southwest Michigan. He likes my '26 Touring (which is not for sale) and wants something similar in terms of condition, i.e. may need a littletinkering, runs, drves, not a project.

Thanks everyone.

1909-10 Cylinder head with an old but nice repair. There are 4, approximately 1/8”, holes that will need to be filled. Will make a nice head. Very hard to find. $500 can deliver to Hershey if paid in advance. PayPal friends and family will work for me.
Robbie

IMG_8684.jpeg IMG_8641.jpeg IMG_8685.jpeg IMG_8643.jpeg

When I pull the crank gas sprays out of the carb, it looks like it might be coming out of the side of the carb. It is an NH carb. Could this be caused by a stuck intake valve. If I leave the gas turned on and don't crank it no more fuel leaks out. it can sit overnight with the gas valve on and no gas leaks out, it seems like that would eliminate a...

I recently purchased a barn load of T parts. In the process of sorting it all out so what I have is not limited to the following:
I have a number of front wood wheel hubs with front & rear tapered bearings in them. No time to clean them up or check the bearings out and if I did the price would be higher for known good ones. Doubt if the bearings...

Effective December 7, 2020 we are moving. Our new address will be 1118 Jennings Avenue Petoskey, Michigan 49770. Please send me a private email on this Forum or call our old number 859-881-1677, you will hear a message with our new contact information. I will reply if you ask for me to call you back. I am doing this to avoid placing my new...

Already been machined.
Can take to Hershey.
$450

I enjoyed rereading this post and thought others might enjoy checking it out to.

See you there! Jeron Takacs, Seamus Hnat and myself are en-route to Hershey! Currently driving through Ohio.

I have a 1922 touring and lately I have had an issue with it running on magneto. I start it and warm it up and switch to magneto. It runs well for about 20-30 minutes. Then it starts spitting, sputtering and backfiring and then it will shut down.

When it will run on magneto, I have checked the magneto with a lightbulb and increased the RPMS and...

Hubs are 40$ea plus the ride I have a ton of them

hubs 1.jpg hubs 2.jpg hubs 3.jpg ]For Sale: 26-27 wire wheels and hubs. Five wheels and hub set. Local pickup only. Located in Central Wisconsin. $950

Here is a set of hubs for sale.
One rear hub will need studs installed.

$450 plus shipping or best or better offer.

wire wheel hubds.jpg

Hi all, I've got an 09 mother inlaw roadster body at Kim Dobbins that I need shipped to Nevada City area. ( 1 hour above Sacramento). Would easily fit in the back of a pickup bed. Anyone heading this way have room?

I've been helping a friend with information on his original 1915, and here is where I'm at. We are working on ORIGINAL throttle rods that go through the block. What I've found out is the material is 7/32 diameter, and this size was used throughout the entire Model T production. It also appears the alloy has a high nickel content, and was made from...

FOR SALE
1903/1906 Olds Replica
Excellent appearance and mechanical condition
Electric start
Modern engine
New tires and tubes
I never drove it more than 1 mile
Stored on jacks in a climate controlled garage
Spur of the moment purchase but I quickly lost interest because I truly wanted a genuine antique 1903 Olds
$5000 or Best Offer
Located 20...

FOR SALE
1908 Black Highwheeler Motorbuggy Model 112
Made in Auburn Indiana and sold in Chicago Illinois
Barn find and unmolested
Maintained as preservation quality
Runs and drives
Right hand steering
Chain drive
Bulb horn and Bermuda Bell
Original headlights and tail light
Seats have original horsehair stuffing
All wood solid
All sheet metal is...

WTB: 1919-1921 Coupe with a pickup bed instead of the turtle deck. Running and drivable. Not interested in a Roadster pickup. 1919-1921 Coupe with turtle deck will be considered. (Am posting for a neighbor who does not have internet.) All leads are appreciated. Please send pictures via PM messaging. Thank you.

Found and bought..a '26 was...

I have a 1914 Ambulance project that I started a year ago and I have to many projects at this point in life to finish it . This is a quick project that has all the items to make it a neat little WW I Ambulance. Asking $7,500 O. B. O. Send e-mail for pictures or contact# to discuss the project.Thanks, Dennis

Just picked up a mother load of 26-7 parts, Tudors , roadster, coupes, touring and chassis, bunch of wire wheels and hubs, will bring any and all to Hershey, Have titles for six cars all unrestored, just posted on Facebook Model T today of the haul.

One pair of nice 26/27 front wire wheel hubs. No visible cracks. Lugs tight. Threads look good. Price for the pair is $275 plus $16.50 domestic shipping. Mark Chaffin (951)805 0928

Screenshot_20240428_062005_Chrome.jpg

Cleaning up some stuff for mu swapmeet stock today and I stumbled over this among some other trinkets from one of our USA trips. 20241005_131741.jpg It is just about the size of quarter
I have no use for it. If it is of any interest to anyone, just send me an email.

Allan from down under.

First, I want to sing the praises of the MTFCA and especially Mr. Strickland a nearby member. After the flood I posted that I was in urgent need of someone who could get my Maxwell and take it somewhere to try to get the water out of everything. Mr. Strickland without hesitation came to the rescue and went above and beyond to save the old car. It...

The answer is these two have useful tips. They need to be aware of going downhill with retarded spark and not using the parking brake to slow down as much, disconnecting the engine losing the transmission brake.

The 1926/‘27 Fordor has three window shade rods. One longer rear window shade rod and two shorter rear side window shade rods. I have the rear rod and need the two side window shade rods. It does not need to be for a Fordor or for the rear side windows since they are so rare, but two rear window shade rods for any 1926/‘27 closed car (Coupe,...

A local resident inherited a model t truck that had a flat. Tire. The local tire shop would,t touch it and was referred to me. I had experience with split rims on a roadster that I had and unowned that their is a way to lock the rim after putting tire on. This rim had no way to lock it and I am asking if anyone has a photo of what locking...

Has anyone heard from any of our members who are in the Hurricane area? I wonder if any Model T's have been damaged or members flooded out of homes?
Norm

For those of you that have wondered what the competition was like as Chevrolet began to outsell our first love......the Model T Ford, here's your chance to own one. For Sale is a 1926 Chevrolet Superior K 5 passenger touring. This is an older show quality restoration, extremely well maintained with less than 3000 miles driven since it received a...

I would like to buy a 1914 or older Model T Touring for use in Parades and touring.
Thanks,
Jerry
574-952-4550
myclassic29@gmail.com

Everything is brand new as I am now fabricating all the components used. Starter or Generator (use your 3rd brush holder on gens).

I’ll sell some of these to forum members.
.
IMG_0771.jpeg
.
$45 + shipping. (Compare at $60 with used parts)

I will also be selling the rebuild kits with all new components (use your brush plate) for $25+ shipping....

An Original 1920's Facts from Ford 4th addition Sept 1920
Fair condition
72 pages
9 x6 signed on the inside of the from page by H Ford
$65us plus postage

An Original 1912 Ford Times in good condition,
April-May 9 x 61/4 x24 pages
$80us plus postage

Original 1912 Sales Booklet in very good condition
2nd Addition April 1912
12 pages , 6 x 31/2
$125us plus postage

Original 1912 Sales Booklet in excellent condition
32 pages measuring 7 1/2 x 5
$125 plus postage
WE can't get all the photos on so if you want more please ontact us.

Original 1910-1912 Left Hand Drive Rubes triple twist horn, it has a reproduction 65 long brass tube and a repo front has been put onto the horn.
$350US plus freight

Kingston 5 Ball Carburetor #128872. Appears to be in excellent condition. I didn't disassemble it. Everything visual functions properly and is not loosey goosey. $1250.00.
Ed aka #4

Our coupe did not come with a windshield. So, I had no idea what all parts are needed. I went to the vendors and documented everything 26 coupe windshield. Many items did not specify coupe or whether they were for a closed or open car. Remember, our T came with nothing windshield related, nothing to compare to and we started with no knowledge of...

for sale: original exhaust manifold with lovers. very good condition. $200 plus freight
20230225_173929.jpg 20230225_173944.jpg 20230225_174000.jpg

For sale: differential spider $25 plus postage

melbanolan@aol.com or cell 314-575-7115 for pictures

For sale top saddle pads & straps 17/27 $16 pair
windshield rubber H 22/27 $3
horn casing $10
NOS freeze plus brass 3/3 steel 1/3
NOS Mag spools $1.75 each
NOS distributor cap $9
oil pan supports $34/pr. 26/27
dust cap $11 each
plus postage

20230222_094214.jpg 20230222_094235.jpg

For sale: Steering wheel spider in very good condition. $35 plus postage

Now $30 plus shipping

For sale: New in package Brass steering wheel nut $10 plus postage

Also have a black painted used nut, black with most of the paint gone and a fair nickle $5 each plus postage

call 314-575-7115 or email melbanolan@aol.com for pictures

for sale: front axle with Ford script, left and right springs perches with nuts and a bushing $175 plus shipping
in good condition just needs cleaned, only surface rust.
20240619_085254.jpg 20240619_085303.jpg 20240619_085310.jpg

For sale: muffler with cast iron ends and kidney shaped rear hole. has no tailpipe. $50 plus shipping
20220625_203511.jpg

comes with mounting brackets

For sale: Good steering shaft $100 plus shipping
20240611_164938 - Copy.jpg

NEW PRICE for shaft $75 plus shipping

For sale: Running board tire pump $75 plus postage
20240607_135218 - Copy (2).jpg
20240607_135251 - Copy.jpg

For sale: Ford script head with made in USA $100 plus shipping 20240507_155020.jpg

For sale: Wood hubs and flange. good condition $250 plus postage
20220704_113710.jpg

For sale: New Anco timer with rotor, pin and retainer. cover will need cleaned from light rust from sitting. $75 plus shipping
20240201_132938.jpg
surface rust

email melbanolan@aol.com or text 314-575-7115

I am considering to change my Z head for a Prus head from Snyders or a Sherman style head from Lang’s. These look the same, but did anyone measure the volume of the chamber?

In good condition with a few small bumps to the aluminum case cover. Asking $45 plus postage.
Catseye Aluninium Case Reflector 1.jpg Catseye Aluninium Case Reflector 2.jpg
Please use this email address below and NOT the personal messaging system to contact me.
email.jpg

In excellent original condition. Asking $50 plus postage.
Seeley Ignition 1.jpg Seeley Ignition 2.jpg

Please use this email address below and NOT the personal messaging system to contact me.
email.jpg