MTFCA Forum

As I'm working on my wheels things keep getting deeper and deeper. Can somebody give me a little direction on the front hub assembly?

As far as parts numbers and drawings go via this site I only find reference to wire wheels. Not sure if the parts I'm talking about are interchangeable or not but I have wood wheels.

Front wheel inner CUP:

Modern...

Well, sorta kinda.
It's not the worst thing I've seen done to a T. Other than more H.P., though, it won't off-road any better than a stocker!
Right.jpeg
Left.jpeg
RR.jpeg
Dash.jpeg
Engine.jpeg

IMG_4948.jpeg IMG_4950.jpeg IMG_4957.jpeg IMG_4959.jpeg

My first Sprague is complete except for an original tie rod. My second one is missing the pitman arm and some other parts….Who has parts to a Sprague? IMG_7290.png IMG_7289.png

This large Rubes 3/4 twist horn is about 10 tall and is about 6 wide. This is the style with the large bell and rim. It can be used on a right or left-hand early automobile. The original tubing is about 40 long. It's in great condition. Complete with the thumb nuts, screen, adapters, reed, etc. Honks well. The rubber bulb is obviously squished....

A nice, unrestored pair of headlamps that would date to about 1908-1912. The approximate measurements are 9 1/4 in diameter and height and 8 in depth and 7 1/2 inches between the fork mounting holes. There is no name on these so they can be used on any car. One has a broken reflector and the other one is missing a plain lens. There are a couple of...

Various parts as described below. Each will require an additional $18.50 shipping. Mark Chaffin (951)805-0928

20260122_132124.jpg
Pan Arms NOS. All for $40.00 plus shipping

20260122_132018.jpg
Pan support bracket sets (3). All for $40.00 plus shipping

20260122_131651.jpg
26/27 brake backing plate set $25.00 plus shipping....

Good afternoon,

I am new to the wonderful world of the Model T. A little background: I have been involved with the Maine Forest & Logging Museum in Bradley, Maine, for quite a few years now. Back in December, we received a generous donation of two Ford Model TT trucks with Virgil White snowmobile conversions. Needless to say, we are pretty...

IMG_0096.jpeg For sale are 4 new blockley tires and tubes mounted on new rims. I bought these about 4 years ago intending to use them on a project that fell through. They are mounted on brand new rims from Australia and I only put enough air in the tubes to mount them. Never were fully inflated. If you can use them, they will need to be picked up...

IMG_7249.png

I am getting ready to reassemble my 26 speedster and thought I would take a good look at the frame. It has about 1/4 inch sag in the middle, not a big deal and placing a long straight edge on the frame rails shows that they are both straight side to side. However, the frame in front of the rear crossmember is about 3/8 inch wider than frame behind...

IMG_4904.jpeg IMG_4924.jpeg IMG_4905.jpeg IMG_4443.jpeg

Can anyone help me identify what engine and year this Kingston five ball carburetor came on? It is for sale, but I have no idea what it would be worth. You can reach me through the forum.

I got this with a bunch of Model T stuff. If you know what it is, please let me know if you’re interested in buying it please let me know.
IMG_7258.jpeg
IMG_7257.jpeg
IMG_7255.jpeg

I made this pickup from a 1919 running gear. I bought the running gear that included the hood splash aprons, front fenders and gas tank. I added the cowl, windshield and seats. Added the rear box and fenders Runs great. no smoke. also a 1926 frame and wheels with a 1920 engine and rear end. All for $3000. You pickup at my house. Last time I drove...

WTB: cross drive magneto set up for non generator model t engine. Don't need the mag, just the mag mounting and drive.
thnx,
frontyboy

Everything in the first picture. Block with heavy valve doors, and timing gear cover; fan w/brass hub; seven rivet teacup pan; hogshead with pedals and Ford script inspection cover; complete transmission assembly. The block, going by the serial #97901 was assembled in March of '12. The casting date is not really legible. There are no cracks in the...

I'm going to be shifting some things around in the shop, so if i can re-home this soon...
Otherwise, everything gets buried until i'm bored.
No title. I wanted to build a pig 'n ford type racer.
Super nice frame. Clean, painted, lovely. (I drilled out the rivets, and removed the running board supports, but they are here.)
Numbers are present.
'27...

I'm looking for a pair of 1913 1914 black and brass cowl lamps. Please give them up :)

Manny Kourounis

These parts came from a recent estate sale. They were in a box together. Looks as if someone was putting an engine together and never completed the project. Parts included Jahn's standard pistons and rings. Standard valves and lifters. Includes springs and keepers. New crankshaft gear as well. Babbitt looks pretty good. Don't need it cluttering up...

W.T.B. Bennett brake parts. I need a drum and a center mounting widget thing plus anything else you might have.
Email me by the Forum- Thanks, Steve

Just got done wrapping the steering wheel on my speedster. Wondering what the best finish is to put on the jute. Shellack, varnish...?

Sorry but I'm so confused now.

So my rims are Kelsey and look just like the drawing via the drawings on this site under resources. If I look at my felloes they are flat on one side which appears to be Ford under the ford 2845B drawing or 2845C drawing.

So do I have Kelsey rims on Ford fellows?

I really didn't want to 'pollute' some of the existing threads regarding these Copyrights, so I started a new thread. For those in the know, exactly ' what ' is the Copyright actually covering, -or protecting?

Where my confusion stems from in this is that as I understand it, Mel & Leon used existing shapes of Wood that Ford Mtr. Company and...

How do you guys attach new gas filter screen inside the “potato “?
Got some to replace and don’t want to reinvent the wheel. Thanks Dan

I think, some how my New Day timer brush got bent some how when it was disconnected while I was lightly hand cranking the engine by hand.

Hey all TW Timer lovers...by request I've been asked about any new runs for the TW timer. I hadn't planned to til 2027 but I reckon maybe I better. So I will take EMAIL THROUGH THE FORUM requests until Feb. 15, I strongly suggest you PLAN YEARS AHEAD.

Price from 2025 started at $19 ea. for rectangular brush, $27 for the round. You'd think it...

On Saturday Feb. 28th at 10:00AM in Tipton, Michigan Sam's 2nd Auction will take place. More early Model T parts and over a half dozen new early bodies. New 1909 Touring Wood Body that was displayed at the Ford Piquette Plant, a new 1903 Wood Body Four Seat Tonneau, a new 1911 Town Car Body in prime with all hardware, a New 1910 Coupe Wood Body, a...

Ford Times, January 1912.

Hope everyone is staying warm!

I need to ask a real neophite question: Exactly how should I attach to it to lift the engine?

AM getting closer to where I can start removal of my engine and transmission to find what cut my pan from inside.
In the Ford Bible that just arrived they show lifing the engine with an ice-tong type of gripper gadget,
In one Youtube the guy has an eye...

17 - 25 Reproduction hubcaps. Chrome plated. The one on the right stamping isn't as sharpe as the other. $60 SHIPPING INCLUDED

Enjoy Your Day!

Working on getting some anti tarnish coverings made for my car and a few friends. May even make these to sell. So far we have worked out fitted headlight covers for 13 14 models (earlier models will come soon) hub cap covers and speedo covers. Pototyping of the rad and cowl lamps are progressing. All covers are made of water proof black canvas...

For Sale is an original “Icy Hot” Picnic Set with suitcase. There are 4 plates, knives, forks, and spoons. Unfortunately the Thermos is missing. SOLD plus shipping. Lang’s 1-800-872-7871

Brass anti tarnish covers are now available for order! Full sets not yet available but are comming soon. Earlier model headlamps and cowl lamps are in the works. I am a one man band doing this so please be patient with me and my sewing machine we can only work so fast. All covers are hand made to order from anti tarnish cloth and water proof...

This has sold pending payment. Thanks Greg!!

For Sale- new 11tooth rear end pinion gear. This is a left over from a recent project where we needed a new 40 tooth ring gear but not the pinion.
These sell from the usual vendors for over $200.00. This one can be yours for $150.00 plus $15.00 USPS shipping. This is a high quality USA made pinion with...

The Internet is changing so rapidly, even I have to scramble to keep up sometimes!
Now that Flash Player is no longer supported by any mainstream browsers, I had to change a lot of the code for my website. What does this have to do with Model T's I hear you ask? Simple, I had to (temporarily) remove the music library from my website until I could...

Very nice pair of early front spring perches for over the axle wishbone front end. Very good threads, someone did a nice job removing them without destroying them. They don’t have a hole for an oiler so I believe that makes them 1915 and earlier but I could be wrong.

$150 plus shipping in the U.S.

IMG_8961.jpeg

IMG_8962.jpeg...

For Sale is an original carburetor control rod that connects the steering column to the carb. $25.00 plus shipping Lang’s 1-800-872-7871

For sale is an interesting accessory Fan Blade. Look carefully at the photos for condition as some blades are bent. Comes with a 26-27 extended fan hub. $15.00 plus shipping. Lang’s 1-800-872-7871

As I tear my 22 touring apart and subsequently rebuild it, I came across something that I found a little surprising with the wishbone. I replaced the nuts with the proper countersunk nuts after I found the ones that came off the car were the wrong ones. With new spring perches, I put the front axle together and upon installing the proper nuts I...

For Sale is one front fender iron correct for 1909-13 Model Ts. The iron needs to be straightened and may have been repaired at one time. $95.00 plus shipping Lang’s 1-800-872-7871.

Nice pair of front spindles correct for 1911-1918 with correct straight steering arms. No wear grooves or smashed threads. Could probably use some new bushings.

$100 plus shipping in the U.S.

IMG_8965.jpeg

IMG_8966.jpeg

IMG_8967.jpeg

IMG_8968.jpeg

For Sale is a nice hardware kit for a pickup bed or accessory wood body. Rear tailgate hinges are not included but are easily made. SOLD plus shipping Lang’s 1-800-872-7871

For Sale is a Stevens T-122 Driveshaft Sleeve Puller. It’s in nice condition except the end cap on the threaded part is missing. It is still works fine. $250.00 plus shipping. Lang’s 1-800-872-7871

1926 Touring, sudden-onset problem of slipping in high, but low and reverse are fine. Peeked inside for clues and found the clutch fingers quite loose. Had the clutch spring broken in service? Careful inspection showed it was intact, but...

After much puzzling I finally noticed that the clutch spring and spring cup were pushed right back the...

For Sale is a well made version of Fords 5Z-323. Original version not included. $20.00 plus shipping. Lang’s 1-800-872-7871

For Sale is a rare accessory anti theft device. It is connected to the ignition system and will ground out when the car travels over uneven ground. There isn’t any manufacturer marking on the unit. $60.00 plus shipping. Lang’s 1-800-872-7871

I tightened up the hub and all the spoke are now tight. I was hoping for good measure I could just use something like Chair-Loc in the joints and tenons, epoxy at the tenon ends at the felloe, and Spar Varnish for protection. Will that for me based on what you see or are my spokes done for?

Thanks, Darren

For sale is a very nice 1917-1925 Steering Wheel complete with spider. No cracks in rim. $75.00 Lang’s 1-800-872-7871

Fits under the transmission cover. Anyone have anything? Thanks.

Unique aluminum high compression head with Ford script and 14mm plugs. Price is $450 plus domestic shipping. Mark Chaffin (951)805-0928

20260121_154916.jpg

20260121_154937.jpg

I have for sale an early Hall Scott Ruckstell shift lock assembly in very good condition. $250.00 plus shipping to the lower 48. Best way to reach me is through text message, my number is 419-217-8884.

I have a complete set ready for paint - new grade 8 bolts. If any interest, I'll get them out & get some photos. $400 + the ride. Drop me a note through the forum, please.

I also have quite a few Beehive hassler parts available.

Nims water pump. For a non-Brass Radiator car. Looks like it’s never been used. $100 plus shipping to lower 48. Best way to reach me is through text message. My number is 419-217-8884.

One 6“ x 2 7/8 brass mirror for open car. Has one small chip in upper left-hand corner. $50 plus shipping to lower 48. Best Way to reach me is through text message. My number is 419-217-8884.

Three Brass tire pumps for restoration or as is, manufactured by Bridgeport Brass company. $100 each plus shipping to lower 48. Best Way to reach me is through text message. My number is 419-217-8884.

I have a 1912 rear end with radius rods ,drive shaft and housing the internal parts are new from Lang's or Chaffins, or New Old Stock . My age will never use this a good project to finish putting it together if you need one This was from RV Anderson long time ago. the I can text you photos, and I am willing to work out shipping or delivery. Dave...

What is the proper name for the type of fastener that is commonly used with sheet metal screws in applications where a nut and bolt can't be used. they ware always made of spring steel and can be flat or slightly curved with different sizes for different size screws and applications, I loked at McMaster-Carr but didn't really know what to call...

As the title says, however here's the link for it in the parts section as that's where it really belongs. Thanks

Have some NOS 5 to 1 Steering pinions sun gears. T-3519B. $35 for a set + shipping. See pictures. Email me by forum. Thanks Dan.
IMG_5279.jpeg
IMG_5280.jpeg

See add under cars for sale 1919 PU

Finally got another T model, I’m sure it’s a hodge podge of parts but curious what year this looks like to you? Block is a 1919 and I don’t believe that’s the case on the body. Thanks

I'm hoping to find a mint condition tall Canadian nickle rad shell. Dan Hatch sold one a few years ago and if it didn't get used, please write to me.
Ken Buhler

Here is an extra rear hub puller to me. I think it is for a TT. Measure the same as my Ford TT puller. Don’t see any markings on it. See pictures. $40 + shipping. Email me by the forum. Dan
IMG_5118.jpeg
IMG_5119.jpeg

2 piece drive shafts DB axle other early brass Era parts at Turlock A's swapmeet Jan. 24/ 25 spaces C 30/32/34 zone 1 call or tex Phillip 209 769-3384.

FS EARLY T PARTS 1912 JB headlamps 2 piece drives DB front axle. and more brass era parts At Turlock CAL. A's swapmeet jan.24/25 . See Phillip in zone 1 spaces C 30/ 32 / 34. Call or tex 209 769 3384

Looking for 2 each of these top trim pieces for my 27 touring.
Let me know if you can help. Looking for originals not repos.
Thanks for your time
Brent

If I can’t convert from wood to wire I’ll need to find new steel felloes for demountable rims. I just learned from you guys that mine are junk.

Need to explore my options so I can get on the road.

Thanks, Darren

An interesting pedal boot made in Richmond Indiana pedals.jpg

Cold, rainy and snowy Winter days are the perfect opportunity to learn or review the marvels of the Model T Ignition System and Model T Coils.
How they work and how to keep them running well.

The MTFCA Coil Testing and Tuning Webinar on Youtube:

Its worth viewing if you ever wondered about any of the following questions:
What are the major...

It's been 11 years ago that posted looking for information to identify a carburetor. Turned out to be a Wizard or Simmons, no markings on it.

Since then that carburetor has been sitting on the shelf collecting dust. I'm now retired and thought I would take a shot at bringing it back to life.
The two things needed for it are the flapper and the...

So just picked up a set of used rollers Chaffin's was selling recently, got them all cleaned up nice & purty, question being, what is the preferred method for long term storage, especially given I'm in humid/coastal salt air.

Let me know all your suggestions....
20260119_122543.jpg

It was on my WhatsApp app on my iPhone and it was from India. of course, as your former AdminJeff, I was immediately suspicious, but I decided if it was a scammer, I'd string him along for as long as I could just so he couldn't scam some other poor soul. I often make a sport out if it - seeing how long I can string them along. My current record is...

-

Jan 9, 2026

Dear 2026 Bakersfield Swap Meet vendors and attendees,

For personal and practical reasons, it has been formally decided that I will no longer be spearheading the 2026 Bakersfield Brass Era/ PreWar Swap Meet. Therefore, all vendor fees received thus far, or by me in the future, will be returned via the self addressed stamped...

Here is a set of wood plans for 15/22 Roadster. No sure where I got them but I am not needing them. They must have been in some stuff I bought. I DID NOT COPY THEM , THIS WAY I RECEIVED THEM. They are Mel Miller plans. 5 pages total.
$50 + shipping. Email me by forum. Thanks Dan
IMG_5310.jpeg
IMG_5311.jpeg

Turns over freely. Have not even tried to start. I picked up with plans to clean it up and get it running but I don't have the time. Cool piece. I can send more pictures if you contact me. $850 picked up in central New York.

For Sale- Drive shaft, Housing and Radius Rods- shortened 16½ for Warford Transmission for passenger car.
Will Ship, Deliver to Turlock, CA swap meet or pickup in Oakland,Ca. PM or e-mail to DMCGEARSatYAHOOdotCOM.
$100.00 plus shipping

KIMG1965.JPG

Turns out my wheels are a mess. I don't know much about any of this but I think I just need to find wire wheels and hub adapters.

Currently have a 26 coupe of 21 wood wheels and steel felloes.

Anybody have anything for sale that may help me out?

Thanks, Darren

Nice set of firewall brackets.
$100 plus Shipping for the set.
Thank you IMG_2187.jpeg IMG_2188.jpeg

Here are pictures of some spark plugs that I would like to find one of. Was wondering if anyone would know what make they are. They were in a car or an engine that I bought, but one was broken. They have a bell on one side. Thanks Dan.
IMG_5315.jpeg
IMG_5314.jpeg
IMG_5316.jpeg

Here is a Champion X for size.

IMG_5318.jpeg

i am starting this post in possibly the wrong section BUT ... the Duncan,Ok. swapmeet is coming up in March and i am attending to sell as well as purchase some parts for my projects ... i am WANTING TO BUY ...a windshield frame for a 1931 Murry body model A 4dr., Masonic items from the 1900-1930 era , and 4 cyl. Dodge Brothers items ,particularly...

For sale: center bed plate for roadster pickup. mounts over rear spring cross member $30 plus postage
it has rust but no holes
20221205_123517.jpg 20221205_123524.jpg

For Sale- Pan Corner reinforcement brackets. These help prevent cracking of the oil pan and should be used on all engines. They bolt onto the bottom of the oil pan in the corners where the pan flares out for the flywheel.
$15.00/pair plus $12.00 USPS . PM or e-mail DMCGEARSatYAHOOdotCOM.
thanks!

KIMG1967.JPG

I have made several additions to the test rig that I have been playing around with this winter and have more in mind. I have added an AC volt/ammeter to the inverter supply to make it possible to monitor the power consumption with changes in flywheels weights and magnet types. One toggle switch allows me to change from operating the coil box to...

I recently completed rewinding a generator armature. Andre from Belgium and Ron Patterson encouraged me and offered advice to take on this project. Scott Conger offered several recommendations including a technique to eliminate any material shorting the segments. In addition to these people, several electric motor shop owners gave advice and...

Possibly already posted, but with a heavy heart I bring sad news of another patriarch passing. Gary Cooper, one of the last founders of the Southern Nevada Model T Club. He was instrumental in the restoration of the pie wagon. Screenshot_20260119-062125_YouTube.jpg

I have one pair and 3 other single pieces.
$65 for all of them including shipping to USA 48
Please call or text me at 33zero 3nine one nine zero 62 Thanks Dave

I have a set, possibly 2 (I have to look again)
No bolts but they’re nothing special.
$150 per set and I’ll include shipping to 48 USA
Best way to contact me is 33zero 3nine one nine zero 62 Dave

I have 2 sets, threads are good. $50 each includes shipping USA 48.
Please call or text 33zero 3nine one nine zero 62
Thanks Dave

Is anyone selling Michelin 30X3 1/2 tubes in the US?