MTFCA Forum

1915 non-starter runabout. 12 volts for LED tail/brake/signals, and coils only when starting. Phone/hot spot charging. 12v tire pump if needed. Magneto battery charger.

What do you electrical/battery experts think of this?

I hope this works

As of August 1st, the contract was signed and now Bill and Shawna are here today getting ready to load all the reproduction parts and machines to its new home, they will have the toll-free phone number 1-888 MODELT1
Also, they will continue making a lot of new reproduction parts, there is a new website they will open very soon; it has been a...

I know its probably been asked a million times, but what oil do I put in a 1926 Model T? The engine is all original except for the valves. Can I use oil from my local auto shop?

Thanks,

Anybody interested in a third annual OCF MTFCA Forum Reunion ? We had a great time putting faces to names, seeing our Ts and, meeting. Let me know through the Forum and if there’s enough interest I’ll coordinate. Looking forward to hearing from you.

Hi

I'm in the process of making my Touring 1926 made in Canada drivable again.

Looking at the front spring and the shackle made me skeptical. Do these shackles belong to this car? Furthermore, there are no holes drilled for an oiler on the 7-blade spring. The corners of the top two sheets are not broken.
What was original on the Ford back then?...

I just listed my 1915 Model T Racer on the B.A.T. auction site.
Take a look:

Rod
PS:
This is one FAST little car!!!! :D :D :D

Are the hinges for the 1914 windshield,brass or steel? What are the dimensions of the top and bottom frames.

Mine has steel hinges and look like later hinges. When installed and set up it appears to have too large a gap at the center fold.

Any information would be appreciated.

frontyboy

Hi.

I just disassembled my rear end and it's my turn to gather the parts needed for a rebuild. I'm not that experienced with the model t. Was therefore a bit surprised that there is no seal between the differential and universal joint. I have already read in the forum that engine/gear oil can run into the differential. But I think the opposite...

Does anyone have a set of the Keystone reamers like this with a good label? I need a picture of it for mine. Can’t read mine or this picture either. Thanks Dan
00A34BAF-C103-42FF-AF48-FA54DCB7952E.jpeg

There are a few Model T Clubs about.

There are a few Model T parts supplies about.

There are some manufacturers of custom copper gaskets in North America.

There are a couple Model T Fords being driven and maintained.

So, why can't the few clubs that cater to the Model T, approach the custom gasket manufactures and request x number of rare high...

I know it’s not easy but Iam looking for parts for the American Bosch distributor. Type T-448. Manly the distributor cap. Part#65942. Also any surviving information books on the distributor. Thanks B6E467FE-99CB-4721-9808-92D022F342D6.jpeg

Iam looking for any information related to the American Bosch front plate distributor. Parts books, installation information and the like. 48CD81C0-7475-4D03-BA7A-8D5FB5EFA56F.jpeg this is a type T448 that I have obtained. Any help is much appreciated.
Bryant

here are two photos. I am seeking bids for the model 30 8 valve head. If shipped the buyer will have to arrange packing and shipping. I am not able to pack. There are 7 pushrods - rest seems complete. See my other Rajo postings for other photos.

Description and prices are as indicated below. Please add an additional $9.50 for domestic shipping per item. Combine several items and save on shipping. Mark Chaffin (951) 805-0928

ROAD GEARS.jpg

ROAD GEARS

1. STEWART 35 tooth #6486 35T 8P $50.00
2. JONES 35 tooth #850 35T 8P $50.00
3. VAN SICKLEN 35 tooth 35T 8P $50.00
4. UNKNOWN 35 tooth...

After years of false starts, overstated product, and eBay bidding wars for complete lamps that were not right…

I am finally but one piece shy of a genuine set of E&J #8 lamps.

Yeah I know…but if anyone has a scrap lamp or a rusty reflector, or even a decent one…shoot me a PM?

I only need the reflector, but would consider a whole donor lamp...

two more photos. see other postings. do not want to ship. Pick up here in Minnesota. Want you to view. Seeking perhaps $2200. What do you think. This includes the manifold.

Darel

Here are the Rajo head photos

The unsurpassed Dykes Automobile Encyclopedia, famous for 940 pages of great reading ( it is 2 thick). Earlier Model T production era 12th Edition (1921) with the famous Model T Ford supplement section, aircraft, trucks, tractors, motorcycles, carburetors, general engineering, generators, magnetos. and on and on seemingly forever! Nicely indexed...

Looking for a decent brass touring closer to Michigan the better

Want To Buy an auxiliary brake adjustment link. This is the link that attaches to the welded on tab at the bottom of the brake pedal. Evidently, this link is not supplied with/in the Benet Auxiliary Brake package. I know this link is available from a reputable vendor. I will buy one there if nobody has one they want to sell.

Thank You,
Terry

So the first thing I noticed is that the hubcap was filled with grease. Not sure this is necessary. So my first question is: Do you have to have all the grease in the hubcap and all over the nut?

IMG_5959.jpeg

My second question is. How tight do you make the bearing and the nut? I'm used to my Mopars, spinning the wheel while tightening the...

I have been holding this body for a buyer since April, I think it's been long enough.
It is early 1912 Torpedo roadster body that is all original. The body seems solid except for a rust out in the lower right under the seat. Wood is solid. It comes with the top bows and some of the original top. The bows are in perfect condition with no rust. The...

Several days ago, I had the tire removed from a wheel for my 1927 coupe. I then took my five wheels to a local powder coater. I will share some information about the tire and some photos of it and the wheels.

The tire was one of the four tires that had been on the coupe since 1954. To the best of my memory, air had never been added to it nor to...

I have been sending DB emails but no reply. Donnie please check your email, I have a question. Thanks Dan

For sale: never used exhaust manifold $80 plus postage
20220528_174804.jpg 20220528_174754.jpg

Need a couple of gas headlight reflectors as used in 1914 headlights. Used is okay if will polish up. PO of my car (1914 Touring) installed sealed beam bulbs, but the retaining method doesn't allow focusing the bulbs. I want to eliminate the sealed beam bulbs and install the halogen adapter (or LED bulb, if available) for a cleaner look. The...

I have one of the exhaust pipes that Original Smith made a couple of years ago.

I remember reading that it used a somewhat different exhaust manifold than the traditional one the vendors carry.

Does anyone have an exhaust manifold that this exhaust pipe will work with?

I'm making a timeline and comparing the activities, Ford Motor Co. related, of the two major shareholders, Henry Ford and Alexander Y. Malcomson. Of the board meeting meeting minutes I have (1903-1906 when both men were involved with company), I've found one instance where a director made a motion, and not only had the motion fail (infrequently...

So my brother said that old grease (from the 60's and 70's) mixed with modern grease can have a chemical reaction that can cause the grease to become corrosive and damage the wheel bearings. I know all the old should be cleaned out anyway but if that's true and you don't get it all out.........Any thoughts?

Early timing cover (12-14) $40.00 plus $9.50 domestic shipping. Mark Chaffin (951) 805-0928 SOLD

20220803_175237.jpg

Weak magneto output afflicts many Model Ts. I wonder if it would be practical to make replacement magnets that fit in the original magneto assembly but had the power and durability of modern permanent magnets. Many portable generators have permanent magnet rotors that operate sucessfully under conditions of heat and vibration at least as severe as...

Late 11' to 12' aluminum transmission cover. No reinforcements around bolt bosses. Pedals in above average condition. Shafts are tight in the holes. Later incorrect inspection cover. Will also need reverse and brake clutch cams to complete. Price was $400 now $300 plus domestic shipping. Mark Chaffin (951) 805-0928.

20220809_170756.jpg...

Speedometer cables and housings. Some housings with drive cables and some without. Description and prices as indicated below. Domestic shipping is an additional $9.50. Mark Chaffin (951) 805 0928

20220814_122602.jpg

1. Stewart housing 63 steel without cable $50.00 SOLD
2. Stewart housing 60 steel without cable $50.00 SOLD
3. AC housing 66...

Does anyone know the length of a new one. I love how my T runs with this timer. The brush is getting quite worn down. No brushes available anywhere, but I’m sure I can make a new one.

There is a nice selection of Model Ts going to Auction on August 27th at the Owls Head Transportation Museum. 1911 Touring, award winning 1913 Touring, 1914 Touring (No Reserve), 1921 Centerdoor, 1922 Roadster, and 2 Ton Trucks (No Reserve)

A young member whom is disassembling a T engine called and asked if there were ever a spacer disk at the transmission & crank union. He described it as looking factory with holes in it aligned with the bolt holes on the crank. Any ideas?

I have been pondering for years a way to circulate extra water to cool the rear cylinders in my speedster engine. I always imagined something similar to a Fronty water manifold fed by a water hose tapped off of the standard water inlet casting. The more I think about it... the more I consider making an authentic Fronty water manifold to do the...

1914 model T Touring, seems to be mostly original body, has newer engine with battery & starter, runs be needs carb cleaned, can use as is or restored $11,000 OBO
call 215-962-9480 in the Phila. Pa. area

Hello Guys, looking to buy and running and driving Model T in Arizona. Any year or body style.

Shoot me an email if you are selling. sbill4768@gmail.com

Thank you

All ten Jan/Feb issues between 1970 and 1979. $20 plus $8.45 for flat rate envelope.

See pic. Paypal or check. Please send PM.

Supposedly in about 10 weeks a run of about 350 copper head gaskets are going to be available…
Anyone confirm this?

Description and prices are as indicated below. All items listed will need restoration prior to use. Please ad an additional $9.50 per item for domestic shipping. Combine items and save on shipping. Mark Chaffin (951) 805-0928

DRIVES.jpg

SPEEDOMETER DRIVES AND BRACKETS

1. JONES MANSFIELD drive 1:1 ratio brass body with 16 tooth gear and...

Thirty-one (31) issues of The Vintage Ford from between Sep/Oct 2016 and Jan/Feb 22.

You paly $19.20 for USPS Large Flat Rate Box

Please send PM. Payment by Paypal or check ok.

I am replacing the felt channels for my 1927 coupe door glass, and it appears this is going to be very, very difficult.

The felt channel is attached to metal channel by a clip at the bottom and a clip at the top. These are shown in the third photo. The top clip is on the left. The metal channel has a round hole and a slot near the bottom which is...

I have a friend with a 13 (no starter or generator) with Mag issues.
History -Restored in Virginia in the 80's and stored in a controlled garage with very little use. Imported to NZ 2015 and only done a few miles since.
Last year it wouldn't run (even idle) on Mag at all. We recharged the Mag in the car and now it runs but not a smooth as when on...

Two eight-inch vases (pink and green). Only flaw is half-inch chip off base of the pint vase. Includes one holder/brace.

Two Phinney-Walker rim-wind car clocks from the 1920s. Both are complete, but not working.

One Mobil Oil advertising tire tread gauge.

One vintage Rainbo Cap cover for dash light. Used, complete and in good shape with...

Ten issues total: Jan/Feb 91, 93, 94. Mar/Apr 91 and 96. May/Jun 80. Jul/Aug 96. Sep/Oct 78 and Nov/Dec 78 and 96.

You pay $8.45 for flat rate envelope cost.

Send PM and check or Paypal.

See pic

for sale, never used stainless steel top irons for a 28-29 model a $250 plus shipping topiron2.jpeg top iron1.jpeg

Like the ad states please let me know what you have excess of. Please send pictures via email if you can.
Best John

Original condition HCCT. Complete, nice gauge face. As found in long term storage. Will probably need new wiring and contacts cleaned and tuned up, but what a find. This is a must have item to have displayed in your shop or collection to impress your T friends. Too heavy and fragile to ship, pick up only in Boise, Idaho. 950.00...

Would like to buy a Spark Ring for this style HCCT. Jim Golden, Bowie, Maryland.

Coil Tester Front.JPG

I'm looking for a couple 30 3 1/2 tires for a project car. I would prefer tires similar to the ones pictured below. These are gum dipped American made Firestone tires. New or low miles please. I need at least 2. I will consider other brands as well. Send a private message if you have any for sale. I will also be at the covered bridge tour this...

Here is a pair of NOS Early Pinion Bearing Races. These are stamped Hyatt see pictures. I took these out of a Ford Dealer in Tn that closed in 1928. When was last time you saw one of these? Extra to me, undertaker will not let me be buried with them.
$50.00 EACH + shipping. Email me at address in pictures. Thanks Dan....

Thinking of installing a Prus head on 24 engine that is stock except for aluminum flat top piston’s - also running a Warford w/ standard gearing at rear. My vehicle is slightly heavier than most, extra power would help on hills but I don’t want to shoot my self in the foot here. Crankshaft & lower end issues ? Head gasket availability also a...

Here is a set of unused Scandinavia band linings. These are the good old “pre-tar baby” ones made by Cantex with proper weave after they bought the company way back when. 22.5 long, includes rivets 50.00 includes shipping lower 48

6EC187F1-66CF-4A71-81D4-182F84AD0665.jpeg

What is the use for this puller? It looks like the spring perch pusher but the jaws are twisted to go around something. Thanks for any help. ---dan thumbnail (1).jpg thumbnail.jpg

Noticed that someone is looking for a distributor cap to fit the Bosch Type 600 on the parts forum. These caps have been hard to find in good condition for some time now. I have a nice NOS one that I have been holding back to be used as a pattern for reproducing them at some point in time. There is a company that I have contacted that will...

This is a very early 1909 exhaust manifold with the large part number 512. It has been repaired and has a 1.5” crack leading from the old repair. I definitely can be repaired, this is a very rare manifold. It is warped about 1/16”. $85.00 plus $20.00 shipping. Kdmks AT att.net.

Original sedan sidelight bracket, 30 shipped lower 48

E0A45371-B35D-46F3-AFE3-70A2E286C82B.jpeg

Reproduction brass roadster tail lamp bracket , 30.00 shipped lower 48
203248AA-9957-40C3-9D3E-E13B29A75382.jpeg

13-14 tail lamp bracket, cast steel reproduction 25.00 shipped lower 48

A6E5F140-8E75-4A38-B381-763F191F63AD.jpeg

Is an adhesive used to bond the door glass felt channel to the metal retaining channel in couples?

DSC00021.JPG DSC00020.JPG For sale. Battery carrier. Part #5150A as shown in Langs book. $40.00 plus freight.

For sale - 2- 30x3 white Firestone tires and 2- 30x3 1/2 white Firestone tires. I have had them five years on my car while it was under restoration and they were on the car for about 20 years fully inflated before it came to me. They are dirty but unexpectedly flexible but it will leave a chalk looking mark on my garage floor. I just removed them...

Here is a spare brass mirror frame and handle parts. Perfect to repair a damaged mirror or to keep in case yours falls off by accident. 40.00 includes shipping to lower 48.

ACAB3083-60CA-42F5-9EE4-33F49000AB3C.jpeg

Here is a complete business with an established customer base. Business includes 700 plus pounds of pre cut copper strips, winding machine, glyptal dip tank, oven to bake finished rings and blast cabinet. All the supplies are included as well as training. Everything is located in western NY state. Everything plus training for 8k. Let me know if...

Good day everyone
I got my first model T running two days ago. It’s a 1911 with an original coil box. When I turn the key from battery to mag I get a spark plug type shock. Is that normal?

I will post the photos - need to chagne size...

-Is any one imnterested in this head? Pick up in Minnesota Twin Cities. Seeking best offer. has rest--rods, etc. no cover.

Would anyone have a photo or diagram to share of how the rear wood is arranged in a 1926 Touring T?

Hello, I have a pretty good turtle deck off of a 1925. Paint is good. Has key. I can text pictures. Asking $450. Im in central Kentucky. Can meet you to deliver within reasonable distance. 859-319-6534. Thanks.

Listing for a friend. One very nicely restored 27' Fordoor Sedan. Complete restoration both inside and out. Many upgrades. This is a driver! Asking price is $18,000. Located near Long Beach, CA. Give the owner a call to discuss further or to set up an appointment to view and drive. Mike Olsen (714) 713-6923

20220723_111819.jpg...

Just for anyone interested--just saw a new speedster gas tank for sale on ebay, listing under model t gas tanks good luck

20220816_115533.jpg 20220816_115553.jpg 20220816_115559.jpg 20220816_115617.jpg 20220816_115627.jpg
For sale: One piece steering wheel. Ford script and #T902 BO. needs refinshed and the joint needs reglued. $75 plus postage

Early six flute oil breather cap steel (late 14' early 15'). In excellent condition was $45.00 now $40.00 plus $9.50 domestic shipping. Mark Chaffin (951) 805-0928

20220813_115643.jpg

20220813_115643.jpg

For Sale: repo stop light switch new still in bag 12/27 $17.50 plus postage
20220816_115216.jpg 20220816_115242.jpg

FOR SALE: Lower 1/2 of windshield 39 1/4 x 12 open car 15/16 and 17/22 $100
oil screen 11/27 $15
horn button with wiring 18/27 $20

rear spring perch $20
steering column to firewall lower support bracket $15
20220620_115753.jpg 20220620_115814.jpg

I plan to drive my 1915 from Kansas again, and Dave Hjortnaes aims to drive his touring (1922?) from Wisconsin again. Anybody else driving from outside the Detroit area?

IMG_3689 copy.JPG

Description and prices are as indicated below. Domestic shipping is an additional $9.50. Mark Chaffin (951) 805 0928

20220814_084205.jpg

1. Coil points NOS (4 Sets) was $40.00 now $35.00
2. Fender eye bolt set $20.00 SOLD
3. Mazda auto lamp box with bulbs was $25.00 now $20.00
4. Front shackle set NOS threaded for brass oilers
Was $ 40.00...

Front spring perch set. Good threads. One with bushing and one without was $50.00 now $45.00 plus $9.50 domestic shipping. Mark Chaffin (951) 805-0928

20220813_115610.jpg

Yesterday 10 early Fords left New London and traveled 125 miles to New Brighton. I am happy to report all 10 crossed the finish line. 2 -04 model A, 1-model N, 1-model R, 2-model S runabout, and 4-model S roadsters.

I recently obtained an original copy of the Hyatt Roller bearing catalog covering the period from 1897 - 1916.

In it, Model T Ford axle bearings are listed as part number 16080 for the RH side of the car and 16079 for the LH side.

I wonder why Ford specified different part numbers for the two sides, perhaps the rollers are wound in different...

I dont know too much about Model T coils but from what I understand when checking a coil and you find the primary or secondary windings are damaged that the coil is not rebuildable.
I noticed that Snyders and Langs and maybe others sell the secondary and primary windings. Does this mean I can use these to rebuild those non-rebuildable coils ?...

I have been trying to purchase a 1912 Torpedo from a guy and made him what I think is a generous but reasonable offer. The car is not mint, but fairly nice let's say a 7 out of 10. Needs tires, probably wheels should be redone as they are the originals, the upholstery looks good but not what I would consider a show car. It is painted black rather...

Here is a misc lot of needs work accessory parts. A couple trouble lamps, and a mistreated boyce motometer. It has good glass on both sides, but the plate is water damaged and the thermometer is junked.

Asking $20 plus shipping to anywhere in the world.

If you're going on the Tour from Hamilton, OH to Metamora, IN on the 22 of July; I live 5...

I'm interested in buying a used TW timer with brush holder. It can be worn out. I'm making a new timer for a friend's 1906 Franklin and want to use the guts from a model t ford timer. I would love to set him up with the TW design.

Please email me if you have something you are willing to part with.

Thank you.