MTFCA Forum

This is not my favorite task. I have beaten these out with a long chisel and hammer in the past to remove the ball bearing style, but thought I'd ask for suggestions now. Maybe a little heat on the race or the hub might help? Thanks.

I am working on solving a rough running issue, which means a lot of test drives around the block. This involves backing out of the shop, which is not going well. My technique is to start with the hand brake on then press the reverse pedal down and let the handbrake off. Oddly, the car will go backward when the handbrake is about halfway off, but...

A friend says his Model T never had a Hot Air Pipe, Part Number 4582, so he knows it must not need one.

My opinion is that Henry Ford would never put that part on, if it was not required.

There are usually three different opinions about every part of a Model T, am I wrong on the pipe requirement?

Am I the first?
I mentioned I had bought 2 buckets of bolts at our Swap Meet. One was full of rusty ones that looked hopeless. I remembered a jug of muriatic acid I had on hand. After diluting some 50-50 with water the bolts were tossed in for 3 hours or so. Use precautions such as rubber gloves, eye protection and a well ventilated area. It would...

Here is a set of aftermarket Ball Bearing Thrust bearings. They maybe NOS no sure. There 2 of the ball bearings plate and 7 of the race plates. Ran them through the vibration tumbler to remove the surface rust. Can they be used? That will be up to new owner. $30 + shipping. Email me at address in pictures. Thanks Dan...

Now that retired engineer Terry Burtz has designed an improved Model A engine block with five main bearings, oversized insert bearings and full pressure oiling is there any reason the same can't be done for the T?

Having owned a model t for a few years and having repaired the odd mechanical features that were designed into the vehicle, mechanical features that make the car complex and antiquated, by today's standards.

And now newer owners are trying to up grade the car even further with air conditioning, disk brakes, electronic ignition, high tech voltage...

St. Louis MO Today in the Rain. Think the Lady in the TT is looking to be in this post

Thanks to the forum I found that Tom VanMeeteren is able to supply cap, rotor and points for my AK type RA distributor. The cam gear that came with the unit has no slot or locating hole to position it correctly. The distributor sits slanted. I have attached a couple of pictures of the unit. I could find no markings on the plate, just the Type RA...

Cap screw heads that is. The trouble with cleaning parts hour after hour is that my mind wanders to the land of Oz, Kalamity Dick and questions about how the parts were made and when. Many of the Ford bolts in this batch appear to be from one car and have a round depression in the middle of the head. I have other original Ford bolts without that...

I am selling my beautiful and rare towncar due to personal reasons, unhappily.
This car received a new all wood body some 30 years ago by Ray Wells, but did not get paint till three years ago. Leather is to original factory specs and installed by Ernie Romero less than two years ago.
All body off restoration took place within the last four years....

For sale is a 13-14 Brass windshield with 2 wipers. $450 DSC00041.JPG DSC00040.JPG plus freight. more pictures on request.

FOR SALE: Switch plate $40 plus postage. locking kick pedal $10 20220613_063227.jpg 20220613_063249.jpg

For sale, 1924 Model T roadster, has been in the same family since new. Just removed from long term storage. Very solid straight all original car with one old repaint. It still has the original upholstery with a gunny sack cover. Wheels are in very good shape. It has demountable rims and electric start. Engine turns over.$5,900. S. Mn.

Maybe one on the shelf? Or could build one? Please let me know. Thanks!

1915 T chassis with a brand new Syverson body. Have all the body hardware with instructions. The chassis has been blasted and painted. Original front axle, aluminum hood, but no rear axle,engine,or radiator. Has new reproduction fenders and aprons. Asking $2500 for all. 314-578-7203. Mike

I finally got my little red roadster pick-up assembled and put the engine back in the car.
A T friend of mine that have known the car from the past have told me that it is cursed and often fails when the stakes are high and it's function needed. I was supposed to participate the comming weekend in Bornholm Rundt ( Around Bornholm ) - one of the...

Beginning with his racers, Henry Ford recognized the importance of horsepower to weight ratio. His first racers were no fluff, all motor and no creature comfort space eaters, evidenced by Arrow and 999, the 20 hp skeleton racer, a creation made up of two 1904 Model A 10 hp motors, and his 1100 hundred cubic inch six cylinder racer. This carried...

For sale 1926 Model T Ford touring car. 1 owner for 45 years. Wire wheels, Very straight body. Doors open and shut as new. Very good interior. Good top. It still has the original wood floor boards in very good condition. 4 matching wards riverside tires. It runs and drives good. It has an older repaint. No Texting. $8,800. Located in S. Mn. It has...

Turtle deck in good condition. In primer, small dent below deck. small crack in picture with #8. Both can easily be repaired. Price is $400.00. Pickup only.

Pair of used original 1926-7 screw in magneto posts. $25 for the pair, domestic postage $10.

If I set my '27 generator with stock cutout rate high enough to hold the ammeter at zero to 1 amp charge at road speed with the lights on, it shows about 7 amps charge with the lights off. If I turn the lights on with the engine stopped the ammeter shows about 7 amps discharge, which seems too high to me, so I question the ammeter accuracy. It is...

For Sale: Canadian built 1914 RHD Model T Ford ‘C’ Cab. Serial number C22309. Exported, and eventually returned to Canada, restored, from New Zealand in 1991. Five Firestone tires, with balance beads, estimated to be 8 years old, wheels re spoked in 2015. Installed a Brassworks Brass radiator in 2018 as well as a WOSP 12-volt starter in 2019. Has...

For Sale: Wishbone in good condition $45 plus freight 20220528_123017.jpg 20220528_123025.jpg

Wtb,
1914 roadster door. I believe a 1914 touring front door would be the same ?

Thanks
Steve Meudt

Selling the aforementioned parts located in Milford NH. Will ship but prefer local pickup.

Warford cross members with u bolts $175
Speedster seats $300 for the pair.
Turtle deck in great shape. Some dents and dings $400
Luggage rack $50

FOR SALE: Brake rods $45 pair plus postage
Radius rods $45 pair plus postage 20220611_134916.jpg 20220611_134904.jpg

For Sale: Fat man steering wheel $195
battery carrier with brackets $45
Window trim for material tops. 3 windows set includes 3 pcs. glass
6 fram 20220612_181938.jpg 20220612_181927.jpg 20220612_182129.jpg 20220612_182136.jpg 20220612_182112.jpg es. 2 for each window. $50

A Bunch of Hood Shelfs all need a little twisting get all for $45.00 shipped to your door call Matt 503-824-2681

Just took the inspection cover off the bottom of a new to me Roadster. We suspected the motor was rebuilt and never ran. Stuck bore scope into head and no evidence it was started just shiny .20 over pistons. Looks like it has a reground crank and cam as well with new valves, hardened seats, adjustable lifters and new Babbitt. There are dippers...

For Sale: Turtle deck key $7
coil mounting bracket 12/27 $2.50
differential thrust washer with oil grooves on both sides. Brass $13 each
drag link 09/10 $200
steering gear rod ball cap 09/27 $12
front dust cap assembly 09/27 $13.50
crankshaft front seal. felt 2 pcs. 9/27 1.50 each
oil drain plug 13/27 $3

All are NOS

all plus postage

 
UPDATE

I finally found some at Target - $1.29 per gallon.
I use it primarily to mix 50/50 with antifreeze for the T
I also picked up another shortage item - Siracha.
Due to a bad crop of chili peppers this year, it is in short supply.
Most retailers are out of it.
Target is becoming my new go-to over Walmart.

The world is right again :lol:...

I will have a restored 15-16 coil box and a restored 26-27 coil box at space E-1 Thurs. noon thru Friday

I will have some restored 20-25 battery horns at Iola Space E-1 Thurs noon thru Friday.

I will have refurbished starters and generators at Iola space E-1 from Thurs. noon thru Friday. Plus other T parts

Cleaning out the top of an old timers barn. Approx. 20 lbs. of misc Crankcase, Oil Pan Parts. What you see if what you get, remember old times never threw anything away good or bad! $55 and THAT includes shipping in the CONUS. Please respond to this email, jandulics@gmail.com

B25C4E37-C39C-4DA5-9F4B-E800B6035CD9_1_105_c.jpeg...

$50 for this, don’t know what it was made for, an orphan spring do-dad included , $50. Muncie, warford, jumbo giant, Chicago mark 2, I dunno, can be made to work with about any of them. Tmorsher@icloud.com to reach me, thanks. 256D06FE-12FC-4CF8-B381-AD2881407E3E.jpeg 7D835F7B-DD58-4EC8-96F6-1C51AE70EAF1.jpeg

In a previous post a few years ago when discussing this cars tendency to dance/veer left or right when driving over a road repair or similar surface someone suggested that my front end could be in the wrong way around.
I was thinking that if that was the case would the bearing threads be a give away given that they are left hand thread on one...

About how much 600W does it take to fill the rear end on a 1916 properly?

Completely disassembled and cleaned, new needle and seat, float, choke spring and reconditioned spray needle. Test run $200 postpaid to continental USA. Email: wlkma9@gmail.com

1917 Model T Ford Speedster for Sale
This car has never been driven. Zero miles!
The bones of this project were discovered in an abandoned mine in the
California Gold country about 5 years ago.
All frame rails, cross members, suspension and steering components have been
blasted and powder coated. The engine has been completely rebuilt with...

i have been digging thru my stored parts ... i have 2 more sets of re-babbitted Model T connecting rods and a few individual rods for sale ... rods are X grooved and drilled for oil dippers and an oil exhaust hole drilled in the rod webb ...1 set of 1.225 diameter , these are .025 undersize and could easily be lapped to fit a minus .020 re-ground...

Any recommendations on any here in Los Angeles area....or......??

Thanks, John

Anyone that is reputable .....as a hobbiest or pro shop is fine .

thank you , John

Just sorting through some parts that I bought at one time and found what I think is a Model T 10 tooth pinion gear. It looks to be in pretty good shape except for some surface rust. I would appreciate it if someone would confirm that this is in fact a Model T pinion gear. As can be seen in the pictures, there is a divot on the back of one of the...

Sold ! Here is a nice pair and also just single driver side with the spindle arm still attached. $75 or $35 or $100 for all three. Look real good! Lower lIzzy and/or keep a spare, both good advice, tmorsher@icloud.com 56F24C65-AE92-47D0-A618-A210B3BE17A9.jpeg EBDE33A8-CFA2-4BC0-8676-31C9C3C3ACEE.jpeg 11DAEC77-0BFF-47C3-A920-1F32B7090B16.jpeg

SOLD dainty little dash lamp $35 ppd to your door. Tmorsher@icloud.com to reach me, thanks! 11AA9825-D175-48B7-B206-194DACB66EF0.jpeg F7F4C7D1-A38B-42E3-A0AD-E4896A32C9E6.jpeg

Have a aluminum cased Stewart-Warner Speedometer I have only seen one other like it. Speed works Odometer doesn't $125 plus shipping.
Generator distributer drive $45 plus shipping speedo.jpg speedo2.jpg speedo3.jpg thumbnail (1).jpg Dist drive.jpg
Craig.

Hi all,
I'm looking for an inside mirror for my 27 Tudor. Anyone have one to sell?
Thanks,
John

We had our local Father's Day Car Show and Swap meet last weekend. It was a great chance to see old cars and old friends.
I drove the '09 to the show as a contrast to the wide variety of cars there.
SWP22_893.jpg
Kevin had just bought this 15 speedster to add to his vast collection of Red cars including a Ferrari and a Lamborghini. It had passed...

Original 1911 Kingston Coil Box. Original box with stamped matching lid. Original switch. 4 correct Kingston offset contact coils. Includes Kingston key. Box has been cosmetically restored, with correct cherry stain, leaving wood grain texture exposed. Original nameplate. Original brass lid clasps. The contacts are all in nice shape, and the solid...

I replaced the ignition and light switch contacts 30 some years ago. Everything worked ok, but I wanted to have the face plate nickel plated.

After disassembling everything I found the lock cylinder (tumbler) was missing 2 of the 4 wafers. The rectangular end of the pot metal cylinder wasn't so rectangular anymore - a chunk was missing where it...

Our Wonderful Wisconsin Tour is now history, but many pictures have been taken.
Given here are links to over 1400 pictures:

Here is the link and also a tiny url. Both will work.

1-

2-tinyurl.com/2beh2ftf

On the top right corner of the Photo Album page are options. You can order prints for 18 cents and picked up at store of your choice. You...

Last weekend we took part of the international French Model T happening this time in Verdun 2022.
This concentration is each year always on the last weekend of June on an other place in France.
Last time was in 2019, due to Corona,2020 and 2021 didn't happen so you can imagine the joy we had to see back some old freinds.

Here a few links with the...

I need to paint a new aluminum head. Any suggestions appreciated.

Hand air pump with T handle for pressurizing a gasoline tank, complete with large nut for instrument panel mounting, works great and has built in check valve, included is a working pressure gauge $235 for both, domestic shipping $15.

Ball for 1909 1910( note small diameter oil hole) and section of torque tube 1909-1913, both nice originals, tube has been cut off but would make perfect shortened tube to use with a driveshaft transmission at the pinion and retail your clamshell rear axle housings for show! $575 pair, domestic shipping $65.

Need a pair of 17-23 low radiator hood shelves. Not looking for perfect. just good enough to straighten out and fill and paint. Looking to help a friend.
meyre14t@yahoo.com

These were found with Model T parts and may be something that someone needs or can identify.
Stuff1a.jpg
Stuff2a.jpg
If interested more information and discussion are on this thread:

Thanks
Rich

I was contacted by a lady that lives in Elkhart IN that is looking for someone to give her dad a ride in a Model T for his 100th birthday. I would gladly do it except my car is being restored right now (Not running). Perhaps there is some guys local in the area that could do this? He walks with a walker but can get up and down. The Birthday party...

We saw this Model T pickup when we were leaving the Tetons last Monday. Since we didn't track him down I was wondering if anyone recognized it. It had a Texas plate on it. How much fun he must have been having.
Tet22on1.jpg
Tet22on2.jpg
We also stopped at Menor's Ferry in the Grand Teton National park and found this photo of a YPC bus crossing...

20220629_202725.jpg 20220629_202718.jpg For Sale: new tail lights $30.00 each plus postage 20220701_103452.jpg Also chrome frame for a light $10 plus postage

For Sale 1909 Kingston 5 BAll Carburetor excellent shape. $1500.00 Call John 352-256-7234
3CB5347B-3733-4FFE-B201-4E217C934CC5.jpeg

For Sale 1910 Kingston 5 Ball Carburetor. Excellent Shape $1500.00. Call John 352-256-7234.

I am looking for the left side.

I have some questions on my 1925 Model T Coupe.

We ordered new tires and took them to someone here locally who restores vintage cars to have them mounted on the split rims. Went to put them on last night, the first one went on perfectly. No issues at all. All 3 of the others were a nightmare to get on. It seems the rims with the tires mounted...

F/S New one piece, cherry plywood Firewall
32 1/4 x 21 1/2 x 3/4
Langs is selling this item for $160.00 plus tax and shipping, i'm asking $110.00 plus shipping.
2069991473

IMG_2448.jpg

IMG_2447.jpg

I used to really enjoy Dan's posts, especially about his two grandsons. But he seems to have dropped out of sight in the past year.

Dick

Has anyone ever removed this and left it off? It’s impossible to clean under.

Of Melbourne to Moscow fame. He had an apartment in Crimea and a Ukrainian girlfriend at one time, which is what prompted his epic trip. Last I heard from was several years ago when he mentioned going to the US

Primed, good shape resdy for body work and color
Use email: R_Flesnner@yahoo.com or message 509-935-0627

9127ECE0-5812-4497-9255-94D3218E8FA8.jpeg D88DC525-6AB2-4938-9D88-26CBE0A468E2.jpeg CF0531D7-2564-4387-BCE3-6C4B0E836F3A.jpeg B032816E-9225-4167-A2B2-1F72CF605682.jpeg

FOR SALE; emergency brake handle and rod $25 plus postage 20220616_123557.jpg 20220616_123543.jpg

BOTH FOR $120 !!! Here are a couple of nice firewalls. 1923-25 in great shape…….. a very solid 1926-7 fordor or commercial chassis ( perfect for a wood truck or station hack project) these are getting very hard to find. Tmorsher@icloud.com for doing the deal, thanks! D029AE7A-611F-43B7-8693-26D805ECA01E.jpeg

For sale: commutator rods bundle for $5 plus postage
NH spray needle assembly with u-joint and sleeve $30 plus postage 20220630_121835.jpg 20220630_121853.jpg 20220630_121207.jpg 20220630_121207.jpg

Sorry - Double Post due to a cerebral malfunction.

I here so much talk of innertubes not being any count these days. I am getting ready to mount a new set of 450-21, Had already purchased new tubes back in 2015. Opened them up today, and they say, Made In EEC , but no brand on the tube. Are they worth installing? Give me some opinions.

For Sale: 1915 to 1925 coil box in excellent condition $155 plus postage

How can I rejuvenate the reflectors in my sidelights and rear kerosene light?
Should I sand/smooth the back and paint using a high sheen silver?
Right now I’ve got Alumlnum foil pieces for reflection.
What have some of you done?

On another note. If my 22 touring has only kerosene sidelights and a kerosene tail light, does that indicate that it...

I’m looking for a set of 4 FORD (2 front, 2 rear) 28x3 wooden artillery style wheels. Any wood condition is acceptable, what I want is the hubs and rims and I can have the wood replaced. This is for an early Ford project. And yes - I have posted on the EFR site. THANKS MTFCA!!

For Sale: Brass Bridgeport Tire Pump. Very good condition just needs to be cleaned and polished. Not sure if it makes air. Pumps up and down with no problem. $175.00 plus postage 20220630_122513.jpg 20220630_122458.jpg 20220630_122831.jpg

For Sale, column pictured. I hope you can see the tube must of filled with water and froze, distorting the tube. Quadrant and threads look good at top.$75 Steve 701 212 5009

Looking for a pit free 1919-25 rear crossmember. Thanks

I am NOT very familiar with the TT. I do know that the threaded portion is larger than the passenger T and on this assembly and it's marked TT. It's 26/27 with the threaded boss for the radiator valance. The length of the threaded leg is approx. 2 1/2 . Threads look good, may be original Henry's black paint? Spring clamp bar has the matching...

Cleaning out the top of an old timers barn. Approx. 12 lbs. of misc. frame brackets. What you see if what you get, remember old times never threw anything away good or bad! $50 and THAT includes shipping in the CONUS. Please respond to this email, jandulics@gmail.com

8076468A-B218-4DBD-9DD5-39D204D83D2B_1_105_c.jpeg...