MTFCA Forum

If anyone is awake on the forum, I’ve inevitably run into a couple questions installing the new interior.
On my seat base, do I have the carpet correct or is it upside down? And on the shoulder panels, what all hardware is used to install them?
My car had no proper interior in it prior so I am flying rather blind.

Just want to put a shout out to Hank Lee in South Pittsburg, TN. Me and the wife drove down from Jackson, MO to pick up some parts Hank has been sell'n. We came back with a truck load, and back seat too. Me and the wife had a good afternoon talk'n with Hank, his wife Patty, and Hank's dad Pops. I got to see the Green Gentleman's Speedster that he...

Restored and tested Wheeler-Schebler carb and related hardware. Included are the heat stove and flex tubing pieces. These carbs are a direct replacement, and actually better in my opinion than the Stromberg OFs, but not near as common. Asking $650.00 including shipping.

Restored and tested NH straight through carb (early one with the brass throttle arm and cast choke arm). Has a viton needle valve and pressure tested float as well. Asking $300.00 including shipping.

Here we go with that firewall again. The drawing shows ⅜ holes for the two bolts and calls for T-7255 body bolts without giving the bolt size. The bolts used when this car was assembled in the seventies are ⁵⁄₁₆ . I'm assuming that the ⁵⁄₁₆ bolts are wrong and they should be ⅜ , but I'd better check and be sure. I've found plenty of incorrect...

Restored, tested, and guaranteed U&J carb and correct H-1 aluminum manifold. This set-up really works well (Stan was right), tons of power and a smooth idle. I test-ran it for 3 weeks on my '26 and have sold the car so the carb is available . I'll also include the linkage that was set up for an accessory foot-feed/hand throttle combo. The main...

Hi All,

I have just replaced one of the rear axle seals on my 1916 Tourer, and have refitted the wheel. However, despite having it on and off a few times and rechecking the fitment of the keyway, there is about an 1/8 difference as opposed to the other side, and I can see the edge of the brake shoes on the side I have removed.

Obviously I have...

I'm drifting again, but in order to drive this and see my improvements I'll need to get the brakes as good as I can. For some reason the brake pedal won't come back off the floor. It's not 100% on the floor, but close. A time or two I think I heard 'growling' from the transmission as if the brake was actually taking hold. I usually pull the pedal...

I'm currently restoring a late 1911 touring car that has a November 1911 engine serial number, which matches the title. The original firewall still has what is likely the original patent plate shown in the picture below. This number is roughly 2000 higher than the engine serial number. Does anyone know what this number signifies?

The body also...

I painted the engine & exhaust with Rustoleum 500 degree engine paint waited about a week and started the 1916 T and it burnt the paint off the manifold exhaust and tail pipe. Is that normal or do I have a problem?

Original unrestored 1924 Coupe. No rust, All original interior that is deteriorated. All original glass intact. good top. Body is excellent. Fenders have usual dings. Has been in long term storage until yesterday. Engine turns over. have not tried to start. Has good Mn. Title. $4,800. No texting. 507 458 6778. Located 50 miles south of St. Paul,...

For sale, 1926 roadster pickup, just out of 20 year storage. good tires, good body and very straight rust free box. Just in time for summer. It turns over good. Gas and a battery and it should run. It should be a nice easy project. $7,500 OBO. Located 50 miles South of St. Paul, Mn. 507 458 6778.

Need a set for a low cowl 23, should be the metal style.
Thanks

Screenshot_20220523_102141.png Screenshot_20220523_102222.png I am not familiar with this model year / body style. Is this a TT? Most TTs I have seen don't have pickup boxes, and look heavier than this. Is it a TT body on a car(pickup) chassis?

I defer to the profound knowledge of this group. I am attempting to correctly summarise the history of my 1926 Runabout. A few pics at the end of the data. Please review my data summary, and please suggest corrections/additions. Thanks for the help!

1926 Ford Model T Runabout

Built in River Rouge factory, Detroit Michigan in March 1926 SN...

-
TEAM GIANT Model Ts at the 2022 Antique Nationals drag races at Irwindale Raceway, CA.

Drivers:
Gerry Sherman (age 17), Point Loma, California
Stock 1924 Ford Roadster
Jerry King, Hacienda Heights, California
1913 Ford Speedster w/ Sherman Head
-
28758143-28BB-4808-969F-C580A29F9F58.jpeg

Just painted the body of a 24 touring. tired of the black so I tried something newer image4.jpeg

I have a 1921 studebaker and it uses the spring steel rings between the block and the manifolds. I found that some of mine were missing and I wonder if there is a general source that makes these for model T and other cars. Does anyone know where I might find some?

Thanks

I am searching to buy a 1917 Coupelet(two of the three models that year, but preferably the rounded back soft cornered roof, one is pictured below, or either the traditional flat roof, also a pic below, just like the 1918) or a 1918 Coupe. All three of these models in those two years have the removable pillars(removable door posts as some say). I...

Driver's side is a mint fender. Pass. Side needs a little love. Nothing terrible though. Feel free to ask for more pictures. I'm going to put them out there to go for 200.00 for the pair plus shipping they are only 375.00 each new. IMG_20220106_151522321.jpg IMG_20220106_151428052.jpg IMG_20220106_151413493.jpg IMG_20220106_151557057.jpg...

New repops. One has a couple tack welds popped loose. List at 340.00 each will sell for 475.00 for the pair plus shipping IMG_20210903_090533146.jpg IMG_20210903_090616964.jpg IMG_20210903_090716085.jpg IMG_20210903_090634911.jpg

35.00 plus shipping IMG_20220331_113644985.jpg IMG_20220331_113635218.jpg

Good mount for 30.00 plus shipping IMG_20220316_082319015.jpg IMG_20220316_082327774.jpg IMG_20220316_082335819.jpg

Pair of victors fs. Both need reflectors and innards. Bonnets are in good condition other than a dink in the top of one, which can be reached without removal.one door with glass. The door is pretty good with a couple of minor dents. Just spoke with one of the vendors, at the moment doors are available. Asking price for the pair is 275.00 plus...

Handle spins freely.does have some pitting. 25.00 plus shipping IMG_20220427_143800975.jpg IMG_20220427_143807489.jpg

Have a set of new floorboards I purchased at Luray last year that I won’t be using. Made by Jonathan Anderson for an ‘11 Torpedo. Would like to get back what I paid for them, $210. Willing to ship domestically at my expense.

Feel free to reach out.
2013067112

Thanks,
Austin

4 20” TT wheels, looks like you can make 2 good wheels out of the parts. I can send more pictures if interested. $350.00 pickup in Battle Creek MI or I can put them on a pallet and drop off at Fastenal if buyer sets it up. Thanks 269 317 7997

Well after about 10 years of collecting parts and research I've officially started on building my delivery car body. I do this kind of stuff when I have time and $. Thought you all would like to see the progress so far.

Here is all my body irons made up
IMG_0055.JPG

I ordered some Ash wood from the local Amish mill for the sills and the rest...

Set of four T-336 brackets fs, in pretty decent shape. One has two notches cut. 60.00 for all four plus shipping IMG_20220523_105837414.jpg IMG_20220523_105750448.jpg IMG_20220523_105717450.jpg

Posting for the pictures only.

Anyone except me having difficulty fitting 30 x 3 1/2 tubes and flaps into 30 x 3 tires?

WTB: NOS or excellent used old stock bridge washers to fit the SMALL diameter valve stems such as the 777 or 888.

Screen Shot 2022-05-21 at 4.32.44 PM.jpg
I assume some fasteners go in these two little holes. What are they?

New never used wire wheel hub caps. $40.00 plus postage. Can email pictures.

I have three rebuilt Stromberg OF carbs. Complete, tested, and ready to go. I used some of the Tim Morsher steel replacement parts on these carbs. All three have new steel needles (identical to the originals) and the extra choke spring added so you can use the stock T choke mechanism to pull the choke on and the spring pulls it open . All three...

I am in the process of rebuilding my rear axle and I have almost finished. I have barely any endplay that is within specs but now there is binding as opposed to earlier when I had a little more endplay than I like. This is with an original ring and pinion, new seals, and original hyatt bearings. It is pretty tight and hard to turn. Unsure if I...

Looking for the 31-tooth brass ring gear. I have the 6-tooth worm, but willing to buy the complete gear set. Please reply to bowerusa@msn.com. Thank you

I have 3 pair of cast end brake rods for sale. 2 sets are nice, $175 per pair. The pair with the white paint, have been welded and need some more welding in wear spots. $75.00. All plus shipping. kdmks AT att.net.

Hello
I recently brought my 1926 Runabout out of storage to get it started. When I would attempt to engage the starter the car would try to drag forward. So I jacked it up and put stands under the rear axle, reset the air fuel mixture, choke, crank it over twice, turn on the ignition and it fired right up.

However while I had it up in the air, I...

I need two hinged caps for early connecting rods. They would be similar to an NRS style cap. Please let me know what you might have. If they are close enough, I can have them modified.

Herb

Guys I'm looking at adding a 1930 Willys Knight 66B sedan to keep my T's company but cant get any response from the WOKR forum so was hoping somebody on here might have some experience with them. Its a 6 cylinder sleeve engine done 5,000 miles since new sleeves and pistons etc so is well run in.

1. What sort of mpg could I expect from a quiet 45...

360 cameras create some bizarre effects!

Want to buy a rebuildable solid Kingston coil for 11-12. Coil top looks like this, thanks

6EEDCD84-E3DD-4ADF-8082-D21FB5B75C7B.jpeg

New never used. 4 wire wheel hub caps. $40 plus freight pictures are available.

For Sale 1926 Touring. Original paint with embellishments. NO rust out. Completely rebuilt motor, trans, rear axle, and suspension. Berg radiator. Australian tires. Safety glass. Have top sockets and bows. Have title in my name, owned since 2008. Completed 1800 mile trip with this car, very dependable. $6500. I have 9 Model T's, need to thin the...

I'm trying to ID the town in Pennsylvania where this photo was taken.
The Ford dealership is the best landmark to solve this mystery, and I thought
this forum would be able to help.
The picture was taken in the late in 1930 or early 1931.

My family lived near Pittsburgh, and I think that might be a location.
Another location might be 300 miles...

Looking for a way to adjust timing on the side drive magneto. Found a couple pics of the original piece. It would be neat to find one like this that uses the original spark control rod:

239EC0E5-4D27-4D85-9824-BAB11D3BA78A.jpeg 98584638-5C7F-4C12-B1FD-A206F49C94F6.jpeg

Wanted, book written by Francois Therou. Steve 701 212 5009

Does the linkage go under or over the lower radiator hose? When I got mine it was routed under. Currently the rod connection at the timer is rubbing against the belt when fully advanced and has been for awhile before I bought it. I’m assuming that I need to bend the rod to lengthen it. I have the tool to check the timing.

Looking for one 30 x 3 flap. New or good used. Will trade 30 x 3 1/2 flap or puchase outright. I see vendors sell them new but it's hard to justify almost $40 for an item that used to cost $10.

This is a narrow style transmission cover (5th style)
For very late 1909 & 1910. The cover is in good shape no cracks in the perimeter mounting bosses, the pedals are crisp & pedal holes have been sleeved plus the Clutch pedal boss has been reinforced. Really a nice addition. $1650.00 plus the ride to your location. I bought this for a 1910...

C680619B-66B9-4951-97DF-E72143455F4E.jpeg 086F06A7-F40B-4009-AF87-7E41121D63C0.jpeg 1BB98D51-93A7-475E-92FD-008009669D60.jpeg 52615234-755A-411A-9F48-A8FC1AF0F345.jpeg

My wife recently inherited a 1926 TT. I, as the make-believe mechanic, am finding this simple machine to be a bit more complex than I thought. The car starts and runs on the battery just fine. However, when switching to magneto it shuts off. I have not yet created the light bulb tester, so don't know about power from the mag. I do have video of it...

I need to replace the bushing at the front of the oil pan that the starting crank goes through. What is the best and easiest way to remove the old bushing? The bushing is probably frozen into the pan.
Thank you in advance, Craig

These are 1 year only (1909) and I think they are repo. These are very hard to find and not easily made. $100 for the pair plus $9.00 shipping. Kdmks AT att.net.

I have what I believe is a 1923-24 Model T frame $100.00

D9C9EBEA-6D09-4B93-91C0-1F83B9D43E93.jpeg

390F51B9-E98F-41A0-B781-16D6C5B5A20D.jpeg

1926-27 RUCKSTELL CUSTOMER HAD US REBUILD IT THEN NEVER PICKED IT UP. . RUCKSTELL $1,200.00, REBUILD $ 2755.61 3/1 GEARS,
TOTAL $3,955.61
DU4 MAGNITO AND MOUNTING BRACKET $450.00, 2 WARFORD CASES, GOOD $50.00 EA. CUSTOMER PAYS SHIPPING GLEN

While at the Luray swap meet this past weekend I picked up an almost complete set of Clum Model T keys. Instead of having 51-74 on them they are marked DB101-DB124. I’m missing the DB117 which corresponds to a #67. If anyone has one lying around, please let me know. I’d like to buy it! I’m setup with PayPal or can send a check/ money order. Please...

I have a friend who just received his new Hartford tubes with rubber valve stems. He needs to know if they will fit through the wood felloe of his wheels? I know the ones made in this country ten or more years ago would not. That's really a shame too, because when Firestone and Monkey Ward were making tubes, they would fit.

Looking, for my 1927 Touring,
Differential case
Ring gear and Pinion
Spider
Spider gears
Axle
Axle gears
Pinion bearing
spool
Driveshaft
Break hub cam, left and right
Rocky Mountain Break, lining

Here is a set of new as issued, unused California Horseless Carriage Plates. Very nice. Stored for a very long time. 220.00 shipped to lower 48.

467DCC32-0DF6-4719-B477-D1418F8578A1.jpeg

Has anyone had any experience with the reproduction visor frames? I am having a hard time tracking down an original and an original that isn't all rusted out.

I've had my 24 touring for a couple of months. Heard a little more noise from the crank then I liked so I thought I'd investigate. Henry says there should be a little movement when tapped with a brass hammer, I could get side movement with my hand. Ok, time for Plasti gauge and some shim removal. But looking up the cylinder bores, I see that two...

The hood on my '27 T tends to ride forward until it's too close to the radiator shell. I tried putting a short piece of hood lacing in the front hinge rod clip on the radiator shell. That helped a little, but after a few tens of miles of driving, the hood would creep forward on the hinge rod and again be too close to the shell. I got tired of...

Testing the waters to see if there are any TTs coming up for sale.
Prefer the C-Cabs, but keeping an open mind. A pm is fine, or email @ brooks saint ives at aol dot com (all one word).
Or call 609 920 4220. Many thanks.

Brooks

Have been to the 'Pantheon' in Basel / Switzerland yesterday.
In a special exhibition between others there were a 1904 De Dion Bouton and a 1906 Ford Model N standing side by side.
Interesting to me to recognize the differences between old and new world cars in that case.
De Dion: 700 ccm engine with 6 HP, vehicle weight 560 kgs
Ford: 2419 ccm...

I spent the day helping with an event at the International Monster Truck Museum. A car show/ truck show. A couple of us were in charge of the moonshine race. A timed race picking up jugs from strategic places on the monster truck track. It was open to anything. Of course my T, a 25 DB, a 28 DB, and many 4x4 trucks. 20220521_092911.jpg...

COMPLETELY REBUILT STARTERS NOW FOR SALE.

The 6 Volt starters w/ with BRAND NEW field coils are $375 each with core exchange
ONE YEAR , unconditional, no questions asked warranty ALSO included.
If you don't have a rebuildable core, the Core charge is $25
Shipping is $21 fully insured anywhere in the USA.
.
5 starters.png
.
As soon as...

When I cleaned and painted the frame of my 1916 Touring I removed the gas tank so I could paint that part of the frame and then painted the gas tank. When I put the gas tank back on I could not start the T. I figured out that I was not getting fuel. I must have stirred up the sediment in the gas tank. So I drained all the gas and got a lot of...

In the Canadian province of British Columbia in 1922 they switched from driving on the left to driving on the right.
Curiously While I have seen/found RHD hogsheads in both aluminum and cast iron, I have not seen one with a starter.
Perhaps ford switched to selling LHD cars there in 1919 anyway!

I have recently bought a 1930 Triumph Super 7 car that has been off the road for 22 years. I now have it driving but I have a vibration.
I think its the drive shaft (check the video link) so that's away being checked, straightened and balanced etc.
The car has a drive tube from the diff halfway up the car and then a solid drive shaft about half a...

still looking for # 1800 swivel speedometer joint for mid year 1911 ford. also need correct speedometer cable for same. to complete tool kit need correct spark plug wrench and hub cap wrench (may west style).

Are there any antique electric car guys on here? I have searched the web for interest groups but have not found any. Art

USED rear car axle spiral wound roller bearings part # 2508, these are for both inner and outer and left and right side, lightly used very good condition and measure .002 wear or less on the rollers, no loose cages, limited number available, most have no makers markings but some say Hyatt and a few Ford, all are the original style spiral wound...

I am also going to make a run of the Reamer/Taps for the Stevens tool. Price will be $200 + shipping. If you want one email me at address in pictures. Thanks Dan 1F63BB1A-86D2-4CBF-8351-B678600E540B.jpeg

Has anyone done this and what is required? What are the benefits?
Keith Billet, PA

Did I get your attention? :lol:
I have no connection with them but thought it was fun to see.
ICM1-24.jpg

They offer a Runabout too.
Rich
P S a Speedster too:

Looking for the 26/27 stop light bracket, circled. I have all the rest.

Thanks!

Email to: jerryvan65 AT yahoo DOT com

Capture.JPG

New part, exactly correct. Finishing up a short run and will be available next week

please email me

sorry, no sales to California

Stromberg Bowl Nuts.jpg Stromberg Bowl Nut comparison 2.jpg

I have been getting a lot of questions what is a Stevens Front Axle Tool lately. Guess most from new guys. So here is a link to the video that Bill Robinson made many years ago of the basic of the tool in action. Thanks to Bill for his work in making and posting it.
Enjoy

I am making a run of the cutting tools once again. Will be ready late...

Few people even know that Ford offered shock absorbers as a factory accessory, here is a set! $300, domestic shipping $15.

Right hand Hogs Head for starter car with lower steering bracket.
400.00 plus shipping 20210516_062218_compress81.jpg 20210516_062232_compress80.jpg 20210516_062206_compress44.jpg

So, after a few years in storage, I've been working on getting my 1919 Speedster running.

A few items to bear in mind:
- Rajo overhead Model 30
- Hand crank only
- Texas T distributor with new Champion A-25 plugs
- Carter fuel pump with Holley regulator set at 1.5 lbs pressure; flow test was good
- Stromberg RF carb, no leaks
- half a tank of...

Is this the correct differential case I need for my 1927 Touring

Oval gas tank brackets for sale, 3 pieces. $15.00 + $16.10 USPS flat rate shipping

For many decades , Larry and Bonnie Becker supplied model T enthusiasts with alternators for the model Ts and other old auto electrical parts. Perhaps you remember , Bonnie never went to a swap meet without her Pet Pink Pig, made from model t parts. She has gone to her reward, joining Larry in that big ford dealership in the sky!

I hear there’s plenty but there stuck on a ship. Has anyone ran Olympics before? How did they do?

Finally finished most of the running gear and directed my focus to my roadster body - only to discover a former owner had pop-riveted patch panels along the entire length of both side of the body (firewall to back of bucket) to cover up rusted out panels and (unfortunately) a significant amount of the subframe is also rusted out or paper thin…...

Wayne is having trouble finding anyone that will cut & install early ford windshields for his 12 & 14 T's. Everyone he has been sent to is either out of business or no longer provides the service for flat glass. Does anyone know of someone in the Austin Texas area that will do these.
Thanks.
Craig.