MTFCA Forum

I have a Nash setup on my car. Works ok but the speed registers low. Suspect I have the wrong gears in it. Does anybody have setup information or spare parts on these?

…or more appropriately: whats the Best way to remove this Model T rear axle gear ?… best way to remove 2 little
half moon keepers ? Then; assuming don’t use oxyacetylene, simply press gear off with my 30 Ton press ? Thank you in advance gh

I saw this ad today on the HCCA forum. The ad says that pre-bidding starts on May 24, 2025.

Richard Eagle Collection (Rich passed 8-23-2024)

Online/Live Auction at Blue Mule Auctions, June 7, 2024 – Featuring – 1923 Yellowstone Park Bus, 1907 Buick, 1919 Harley Davidson, 1920 Model T Speedster, many Model T’s, and other cars, parts, literature,...

Would someone happen to have an early water inlet connection original or reproduction? This is the one with a heavier boss for the bolt holes used 1909 to 1912 supposedly. I was given the name Eric Vandenbeemt as one who reproduces them, but I am unable to locate a contact for him.

I should stick to stemwinders. But I am not...

I don't like the location of the original starter button, so I am wiring a solenoid in my wife's 6v speedster (negative ground) and have found two vastly different wiring diagrams:

solenoid wiring 1.png

This diagram makes sense to me. The solenoid takes the place of the original button and a new...

Rebuilding my coil box, but found two coils are leaking tar. Does this mean they are overheating and probably bad?

Very usable set of boards .Has a small roll in one back corner. Believe it will come right back out. No extra holes anywhere. Shipping is so crazy we'll call it 50.00 for the pair plus shipping. A really good deal. The holes are still square. ctleonard64@gmail.com IMG_20250522_130822245.jpg IMG_20250522_130802527.jpg IMG_20250522_130822517.jpg...

Selling for a friend. 2 very nice high heads off a working engine. Owner went to H.C. head hence selling. One is off a '24, the green one off a '26. MAY be able to deliver to Homecoming if another friend goes this year. $100 each plus the ride (est. of $75 for shipping) if not delivered to Homecoming. Reply via email from profile pls. Thanks.

Selling for a friend...very long tow strap.
Multiple possibilities. MAY be able to deliver to Homecoming with another friend. $50 plus a ride if not delivered. PayPal or check. Reply to email from profile pls. Thanks.

Wanted; Early brass steering wheel or spider!

Still selling for a friend. This is the slower starter of the former pair left. My guess is it's very usable, may just need a little TLC. I MAY have another friend going to Homecoming that could maybe deliver it. Connecting would be the hard part but that's what cell phones are for :lol: $75
PayPal or check. Reply by email thru profile. Thanks.

Anyone going to homecoming in Richmond have any good FORD 23 felloes, FORD 23 demountable rims, or used 30X3.5 Tires? If you can bring them I will be a buyer there.

Decent pair of 15 16 only head light buckets 100$ shipped lower 48 these are a hard find

Pair of nice used wire wheel Front Hubs 300$ plus the ride

Hubs are 40$ea plus the ride I have a ton of them

Water neck fan assembly nice shape 45$ plus the ride probably needs bushings

Nice complete riveted fan hub one blade is a bit tweeked tight rivets $30 plus the ride

Plenty of drive shaft spooks on hand 15$ plus the ride

Horn button missing the button inside part isn't pretty probably needs to be replaced as well 25$ shipped

Nice aftermarket tail lamp bracket no makers mark that I've found
$50 plus the ride

….Can’t call them a “set” because Jno Brown 110 on left has a Steel chimney top. Right lamp is brass chimney top. I’d buy a mate for the steel top lamp. Wonder why Brown offered the steel top ? 1914 TT ? :lol:

Here are some more question I have asked before in the past but never received a good answer. I always been confused about the difference between the Model T Instruction Book VS the Ford Manual. This is a 1913 Model T Instruction Book:
ModelT_Early 1913_Instruction Book_Fourth Edition June 1912_From Lau collection.jpg
This is a 1913 Ford...

Hi, I'm kind of new here, and I know this is probably a long shot, but is there a group, or agency, or company, that help younger people, and teenagers buy classic cars? I've appealed to all of my close relatives, and no one has ever owned, or wants to own a Model T, but it has been my biggest life goal for about 2 years now. Does anyone know...

Looking for a Splitdorf plug in 1/2 pipe thread made for an explosion whistle. All you plug collectors or hoarders in general, here is a chance to make some money!

Due to continuing health problems, I am offering the following for sale:
A
Complete and running 1914 chassis with the engine casting
date of 2-3-1914
New Tires, new fuel tank, new brass & oak steering wheel
Excellent radiator, Bee Hive Hasslers at all four corners.
POR painted and completely detailed chassis.
POR Ultra High Heat Painted...

I am in the process of building a speedster using a Rootlieb speedster kit and I need a set of 1911-14 Frame to Firewall Brackets.

Beede & Sterling test meters for Mag. & Amp. $25 each or $45 for both + shipping. Tested & work.
IMG_3591.jpg
Craig.

Old, original Aermore four (4) tube - 13 , 10 3/8 , 9 , and 6 3/4 Brass exhaust whistle mostly covered with probably close to a century of tarnish and road dust. Some folks like the patina of old, so I left it unpolished, as found. However, I did polish a small section to show an interested individual that it is indeed brass, and will shine...

Part of my rocky mtn brakes came off and vanished into the ether the other day. I don’t need a whole new set, but some of the parts that went missing on my country drive. Where can I get just some replacement parts?

Making room for bigger and better toys! This is kinda T related, as it regularly dimples new wire wheel rims, and may have even made T parts when it was new. 20 Tons of fun to annoy your neighbors with! Nothing says “it’s Sunday” like the “ka-chunk ka-chunk ka-chunk” of a punch press on a calm morning. You can even tell em good nite too. First one...

MAJOR widespread flooding in Taree and surrounding areas, unprecedented rainfall with more heavy rain forecast (as of recording this video).
Definitely NOT Model T driving weather! Over 300mm (12 inches) of rain have fallen on Taree and the Manning Valley in the past 24 hours since posting this. The Australian Bureau of Meteorology is forecasting...

Making room for bigger and better toys. Here is the first set of Buffalo hub nuts that I made for my speedster almost 20 years ago. Ran em for probably close to 10 years before swapping over to my current design. Made from aircraft aluminum, special wrench included, could use a polishing touch up. One of a kind set. $500 plus shipping...

This is the BEST pre-war swap meent in Northern California! We will have a space once again.Looking forward to seeing Model T Forum members once again at this great swap meet! I'll be the guy in the Engineers Bibs. Stop by and say Hi! ML Swap meet 2025.jpg

How should the bolt flat contacts be in relationship to the crossbar when the switch is activated?..., Should the rounded flat contacts or the 9/16 inch square flats be in the line with the crossbar??

The cotton linings look a lot like cotton web you can buy by the roll off Amazon, can I use cotton web that's the right width and length of course? (I need to just replace my low band)

We will be having a T parts swap meet on Monday evening July 21 during the 68th MTFCI tour.
This will be a totally free swap meet at the Doubletree Hilton hotel in Owatonna, Minnesota. This has been a popular feature of these tours over the past several years so grab your surplus parts, your wish list and come enjoy the evening. Car games and...

Believe these to be 11-12 only because of the countersunk holes. Also believe they are reproduction. 60.00 plus shipping. ctleonard64@gmail.com IMG_20250317_083355064.jpg IMG_20250317_083440522.jpg IMG_20250317_083415819.jpg

Anyone happen to have one of Bob's tail piece alignment castings not being utilized ? Top dollar paid or possible trade for goodies ! I realize there are other castings available but not to my liking ! Thanks for looking !

Helping a guy that has a 1912 put together car with a lot of incorrect parts.
Ran out of threads on the tie rod and still have too much toe in, over 1/2 . The tie rod is 46-3/4 which from what I can find is correct.
Thinking might have bent spindle arm. I noticed an approx. 3/8 difference when measuring from the inside face of the spokes to...

Antique car conversion chart.jpg

First time wheel rebuilding. They're Hayes wheels, bought Hayes spokes. First problem was the tenon was slightly too big to press into the fellow. Turned one set down, as an experiment (before doing all 48). Got them pressed in.

IMG_2079.jpeg

Was all excited then decided to mount it on the car and spin, wobbly. About a 1/2 ! So I check the...

I just got my 22 out for the first time this year and I am having an odd problem. It’s running a bit rougher than normal but accelerated ok in low. But when I shift to high it lags and there seems to be a bit of a shudder. I adjusted the bands the other day to get just a touch more bight on the low and brake pedals, but only a turn or so. It drove...

I would like to buy a block with a casting date between 9-1-13 - 12-15-13.

Let me know what you have and text me a couple of pictures to 901-496-8795.

Thanks.

Bill Everett

Cell: 901-496-8795

On the California Rendezvous tour last week, my 1913 touring turned over 56,000 miles. It still has the original engine. I've owned this car since 1961, and finished restoring it in 1963. Can anyone top that?

Nice south bend lathe, circa 1940. New drive belt, 3 jaw and 4 jaw chuck, steady rest and full set of collets. Lots of cutting tools and other accessories. 9 inch swing and 48” bed. 120 volt. $750. Pick up only, Los Angeles. kdmks AT att.net.

a couple years ago I asked if anyone had been in the situation of only being able to go in reverse, no forward low or high. no one ever had that problem. I didn't want to tear the engine apart, so it sat on the back burner for a bit. I wondered if the pinion gear could be spinning loose going forward and tightening up in reverse, I took the rear...

I am new to the Model T community but not to early cars. I am in the process of reassembling my 1912 engine and looking for tips on reassembly for such info as torques, avoiding oil leaks etc. I can't find such info in the club restoration videos or the club utube channel. Am I missing something? I do have the black book which is helpful....

three plus two. what make. Has a Minnesota plate.

Picked this up a recent estate sale. One 10 Tooth pinion with Ford script. Looks to be in very good condition. Price is $75.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250514_141046.jpg

I need two rods for a rebuild. The two that were taken off have lost a good amount of thread due to rust.

Thanks for any help.

Scott

Facebook link is for the Hank Lee M1 Rebel.

If you have not seen the build video, here it is:

I am still looking for one more Gets Manufacturing spark plug. All you spark plug collectors, here is a chance to make some money!

If not mistaken-which happens alot- believe these are for 9 leaf. 25.00 for the pair plus shipping. ctleonard64@gmail.com IMG_20250521_131455207.jpg IMG_20250521_131513673.jpg

30.00 plus shipping. ctleonard64@gmail.com IMG_20250521_124847300.jpg IMG_20250521_124842166.jpg IMG_20250521_124827746.jpg IMG_20250521_124816157.jpg

Great for speedsters. These were ran back in the day. The Lynnwood flathead dragster makes for good reading. 100.00 plus shipping. Ctleonard64@gmail.com IMG_20240510_094320261.jpg IMG_20240510_094332361.jpg IMG_20240510_094338489.jpg IMG_20240510_094348020.jpg

Actually the whole rear end. Two-piece driveshaft, forged end radius rods, 13 -14 rear end,, Chicago duplex cantilever spring assiste. Richmond is coming, I'm in mt.vernon Indiana. Come load your truck. 800.00 for driveshaft alone. If you take it all( minus wheels) the price is 1250.00. ctleonard64@gmail.com IMG_20240524_150239587.jpg...

I'm in need of two 26/27 rear emergency drake drums.
Thanks, Steve

I'd like to buy one set of Mospico offset type spindles.

Please send me a picture of what you may have, and $$ wanted.

Thank you.

Model T Offset Spindles.jpg

Been blasted and all old grease cleaned out. All rivets are tight. 75.00 plus shipping. ctleonard64@gmail.com IMG_20250521_111847138.jpg IMG_20250521_111830766.jpg IMG_20250521_111816120.jpg IMG_20250521_111801382.jpg

Nickle plated brass ball valve (made in Italy) that due to it's construction, has the best throughput of any valve available
all brass construction of USA made fittings - NO COPPER line to fatigue or damage when tightening onto the carb (the removable connection is a double-ferrule design which is an industry standard industrial fitting designed...

For sale 10 tooth pinion gear
$80 free usps in the usa.
Just washed it off so you can see it.
Nice used condition.

Has a couple of miles on her. Still a respectable hood. 150.00 plus shipping. ctleonard64@gmail.com IMG_20250520_095048694.jpg IMG_20250520_095027444.jpg IMG_20250520_095018882.jpg IMG_20250520_095248930.jpg IMG_20250520_095245891.jpg

Looking for a pair a single or parts for E&J Model 66 headlights (the black and brass type). Also does anyone know of a person or service that restores brass headlights?

Thanks

Two Stewart Speedometer Roads gears #1322 (60 tooth). In good condition. Price is $30.00 each plus $8.50 domestic shipping. Mark Chaffin (951)805-0928

20250516_161818.jpg

Pair of e and j 440 headlights. Blasted and primed. Good solid buckets. Both reflecters are good. One brass ring has a missing lens clip on the bottom. I believe the arms are early 15, but the adjuster screw is on the left. I don't know the relation to the screws left or on top. 200.00 plus shipping. ctleonard64@gmail.com...

I’d like to put something out there that never really seems to get mentioned about the Prus head. Of course the power difference it offers is a noticeable improvement on our cars, but the one aspect that seems to be overlooked is what that additional compression does for the engine’s retarding ability on long downgrades.

I live in the flatlands...

I’m located in Southern California and I want to buy a T chassis with an engine. My budget is $1000-$2500

Located in mt.vernon Indiana. A fairly nice homemade touring body. Make me an offer. ctleonard64@gmail.com IMG_20250520_100300791.jpg IMG_20250520_100237572.jpg IMG_20250520_100214284.jpg

Found these at a recent estate sale. Not likely T. Similar to Model A front axle spring perch. I'm calling on the antique car gurus to possibly identify the application.

20250516_114821.jpg

20250516_114850.jpg

20250516_114902.jpg

20250516_114914.jpg

Besides Freighter Jim, are there other reliable shippers for Model Ts. I used Bill's in the past but I think he is no longer doing pickup and delivery. Thank you.

This 1931 Model A Tudor was owned by a gentleman who suddenly passed last year. I am trying to sell it for his wife. Needs work but not dents on the body. I have no idea about the engine. $10,000. Located in Bullhead City, Arizona.

Hello,
I need another 1912 front fender iron. Preferably the one with the eyelet or no cutout at all (i.e. I'll drill it myself)
If you have one, please let me know. Thanks!

I have an update on my quest for back issues of Vintage Fords. The Museum did not have what I was looking for. I have been able to find a few. I am still seeking these issues:

All of Volume 1
Volume 3 Number 2
Volume 17 Number 6
Volume 18 Number 6
Volume 19 Number 2 and 6
Volume 23 Number 6
Volume 37 Number 6

Any help would be much appreciated...

It came in today. Already looked the thing though once.

It's a shame no modern manufacture makes new cotton linings, nos ones would get all used up one day. But anyways I need preferably a set for a 17, I know the 26-27 were different but idk how they differ year by year if at all prior to 26. Thanks.

Edit: just went to s dentist, it looking pricy, I can no longer buy anything for the t till I'm done...

Hello,

This is Steven Cross with Zink Motor Company Ford in Appleton City MO. I am wanting to see if anyone has photos of a T era dealership that includes closed garage door/s? We are a 112 year old Ford dealership operating in a 107 year old Ford designed building. I am compiling a project list for a local historic preservation grant...

I have acquired a CenterDoor with A/C Brakes that I am totally unfamiliar with.
Does it look like they are mounted correctly?
How do I go about adjusting them?
Thanks,
Dave

35.00 plus shipping. ctleonard64@gmail.com IMG_20250520_123048039.jpg IMG_20250520_123104135.jpg IMG_20250520_123057123.jpg

Hi All, I am looking for a 26/27 Left Rear Brake Arm/Lever. Please contact me if you have one for sale. I can remove the arm from the shaft if needed

Thanks

Tim

American Bosch 600 series Distributor complete gears, pin, spacer. Has been disassembled, cleaned, lubed, adjusted & bench tested. $200 plus
the ride If you are concerned about replacement parts Tom Van Meeteren has lots of replacement parts. IMG_3493.jpg IMG_3494.jpg
Craig.

Does not leak. In mt.vernon Indiana. 425.00 prefer not to ship. ctleonard64@gmail.com IMG_20250520_100819582.jpg IMG_20250520_100725034.jpg IMG_20250520_100745152.jpg

I have what I thought were two early front Model T wheels.
But there is a difference. One on the right is standard 30x3 and the one on the left is smaller outside dimensions. 2 inches smaller on the rim diameter. Both are wood fellow w / oval spokes. What is the smaller one? IMG_1800.jpeg
IMG_1801.jpeg IMG_1802.jpeg

i have 2 -- 26-7 frames,rear axle housings,radius rods,hogs heads,4 dip pans,engine blocks, Send me an e-mail with needs and for pricing. Dennis

Hello,

I have a '26 touring where the steering wheel has a good two-inches of play. All connections from the pitman down are good. I suspect the play is in the steering box.

Assuming my suspicions are correct, can the problem be solved by replacing the pins, gears, and pinion?

Also, can this work be accomplished with the steering column...

I have a set of '26 roadster sill plates that are semi decent except for a couple cracks. Is zinc repairable?

Have an original firewall bracket for pass. Side. 30.00 plus shipping. ctleonard64@gmail.com 17476797024964535630028639782110.jpg 17476797273017096173120909720160.jpg

Manifold clamp and bolt set (25-27). Includes new studs and nuts. Price WAS $30.00 NOW $25.00 plus $8.50 domestic shipping. Mark Chaffin (951) 805-0928

20250515_103229.jpg

This is a mint as new low profile radiator cap new in the original box. Asking $50 plus postage. PLEASE INQUIRE VIA EMAIL THROUGH THE MTFCA WEBSITE - NOT MESSAGING !
cap 1.jpg cap 2.jpg cap 3.jpg cap 4.jpg

I have a spare Black Decker valve machine. These are the same as a Van Dorn too. I was keeping for spare parts. Since I have another spare I need to get rid of one or part it out. Any interest? If so email me by the forum. I will try and post a picture in next day or so. Thanks Dan

The Mighty Ahooga Head.jpg

The visual impact of a Brass-Era automobile is so striking, it can overshadow the other senses, which is kind of a shame because the way these cars sound is also wonderfully unique, and everyone who works with them just loves the low-revving grumble of a long-stroke engine and the kisskisskisskiss idle of an L or...