MTFCA Forum

I always use the new ones in transmissions builds, especially if the customer requests a turbo or other modern lining clutch. They are not that expensive and good insurance.

Here is a mention of the Model T's after the war finished. It's from a Ford Owner and Dealer magazine from 1920.
Also some Model T's were altered to do other jobs beside the normal Ambulances and staff cars etc. such as turned into trains to move materials along small train track and even as a mobile winch to aid the removal of trucks, tanks and...

I run in the steep mountain roads here in Montana and run two types of oilers. One car runs the stock oiler plus the hogs head high volume type. The other has two inside oilers plus the mag oiler. I don't run a mag so the obstructions are removed from the mag post. Long steep pulls are routine with no problems. I would also suggest scoops on your...

Lisa,

If you haven't already, try Mark Chaffin. He often has parts not advertised here on the forum.

Another source would be Lang's. They're a great bunch of people and are always very helpful. Like Chaffin's, they have a good selection of used parts, but you have to contact them by phone.

The third possible source would be Bob's in Loves...

The reason water based stains are so good is because, unlike oil based stains, water is a natural component of wood and Carrie’s the color deep into the wood. Oil is not a natural occurring component of wood and is not really compatible and does not carry the color deep into the wood. Water is very forgiving and easy to adjust the shade, while oil...

Nope need the seat frames unfortunately the previous owner installed ford ranger seats

Bolts to block

I would like to buy this.

There are also 3 screws that tension the pivot ball. Tighten them a bit.

I had a 1914 speedster with a spring like that or very similar. I really did not notice anything different than normal. But it was a light car. I think mine was a Longleaf brand.
After looking closer to your photo/ad I see the ad shows a double-set of springs. Mine was a single spring as shown in the photo above

That makes sense and is probably the right bar, but unfortunately, still only have one of them. Thanks for pointing that out, Frank.

Didn’t he sell a ruckstell repair book?

The question of how to use this tool comes up frequently. I think someone needs to do a video on how to properly use it before the knowledge is lost to obscurity.

The roadster (‘17?) second from the bottom appears to have an unusually sturdy under axle wishbone to supplement earlier wishbone. And 6th from the top ‘14 touring with acetylene headlamps. Does that electric spotlight run off magneto or 3 telephone batteries ??
Thanks again Tom Rootlieb for these fascinating, thought provoking photos.

Keith T, I have for a long time known of those as a 1912 model feature. However, as many early brass era model Ts and pieces as I have looked at, I can't recall ever seeing one of the timers in person, maybe a couple of the no filler timing gear covers at swap meets, or a 1912 model T with the complete setup.
You say used after October 1911, which...

Sold to Scott.

It will certainly wear grooves in the tie rod where the coil springs rub. There is a better version which has a cast arm mounted to the axle at the front and extending back to the wishbone ball. Both are designed to solve a nonexistent problem. However, if you chuck away all but the cast arm of the better version, you do have a set-up which might...

I have a very nice ee crankshaft I don't need. Please email or pm me.
Scott

I have a number of brass top coils( tested ) available for $15.00 each plus shipping. Also black plastic coils for $10.00 each plus shipping.
Lang’s Old Car Parts Inc 1-800-872-7871

To which e-mail, Steve?

I will take the Do Ray reflectors, pair. Sending an email. Thx / Tim

Don’t worry about moving. Sold pending payment.

Definitely a great find. Is there any way to date them?

I would like the tail light bracket!

I can't say I have one, but I worked for a year in a machine shop that did. It was cleaned up and on display in the entry way to the office.

I tried to buy a Franklin about 10 years ago. It was registered and parked (legally) on a street in Framingham, MA. It had a For Sale sign on it but no address or telephone number. I left three notes on it - actually one note went in to the car, as the driver's side window was down a crack. I never got any response, so I decided that the so-called...

Sold to Tom

I do have one of those, if you would call me rather than email, it’s easier for me, i’m bad at email. my cell is 585-738-1988.
thank you,
Tom Stewart
Churchville, NY

Thanks Alan!

Thank you for your thoughts Keith and others. Craeg's carers brought him to our home for a day visit today, and he was able to see the display stand. I read him some of your comments from the forum and he was quite chuffed.

There is another with mainly T parts. I need a stand for it too. I am thinking this one will look about right on an axle...

The jam nut is only needed to stop the threads on the rod and in the linkage from working . The rods cannot turn, nor can the linkage on the end. If you are about to lose one, it was never threaded on deep enough, or the rod has been loose enough that the wear has allowed the thread to jump a few turns. The jam nut does keep the linkage set at the...

Site just shows picture. Doesn't say its for sale. Doesn't give information on owner/ seller.

Interesting read. Thanks for posting

I have newly acquired 1915 Centerdoor with AC Brakes, which I know nothing about.
How do I adjust them?
Thanks,
Dave

Best to post a picture of them since there were multiple versions. Are these original AC's or repro versions for example. some used rod others cables

Like Bob said :roll:

Late 1940s Chevrolet babbitt rods had a very thin layer of babbitt metal. While a thicker layer might allow more re-fitting, the thick layer will not allow running loose rods and it will not accommodate a flat or tapered shaft. Low speed stationary engines often had babbitt sections of 1/2 or more, but they had bearings with a large surface area,...

Sold to Paul!

Sale pending. Thanks MTFCA.

WTB one rebuilt wood coil or one that just needs a cap. In Wisconsin. Thanks

Tim I've got a big box of coils here some work some don't pleasant prairie area

Can you measure the resistance on side prongs?
I bought couple of coils on ebay and they show open circuit, what means bad wires.
I can replace condenser, but not the coil.

Wayne

It was a brand new engine 4-5 years ago, but I have driven it from Milwaukee to Detroit twice, so it has gotten a work out.

Thank you for the advice. I will have to find a model t owner to help me look thru the hogshead at the triple gears.

Nice looker in number 4. I like the car too!

Allan from down under.

Dude, that could be someone’s grandmother…

Okay...I warned ya! Part deux! :lol:

Beautiful. Thanks for sharing and glad y'all had a good time. This is what it's all about!

Dan McEachern Yes it is, Good Eye! I picked it up at the Turlock swap meet from him back in the earl 1990's. He was a master at restoring Model T accessories!

Beautiful car, congratulations to you and the new owner! :)

A friend of mine and I are wondering if the same guy bought the two Torpedo's that been on here. One to drive, one to keep under a cover? :lol:

If it is, I'd sure like to know what he does for a living!

Wings going to Chad. :)

For some reason, I think the 1915/16 Ts look the best with wires.

I’m a bit biased… but feel that wires look good on em all. Maybe that’s why all my T’s have em… and my dad’s T’s… :?

Wheels? Wheels? The rare item is the Avanti in the lower left corner.
Craig.

The later Avanti II’s had wire wheels… but not a fan! Was thinkin about the...

Here is an older post on making the tool.

I found it Ian. Cast into the underside is TT 1924-B With the Ford script below and an A in a circle, most likely the maker's mark. It has only one hole, for the advance/retard rod, so will be for a generator equipped vehicle. Au$20 plus whatever the postage is.

Allan from down under.

I've already been conversing with these people already and they tell me thismorning that they do not have the parts in their advert picture

This picture was posted at the fb page
covering the recent old car festival.
It was described as being a Californian top. I think the term Californian is now a more generic name for a type of type that turns a touring into more like a sedan with a soiid top, possibly with many different manufacturers of the same concept.

steering control 6.jpg

Please use this email address below and NOT the personal messaging system to contact me.
email.jpg

That is a distinct possibility John !

Plenty of bearings available.

I have a 1916 Touring, great little car, they are not as rare as some other brands from the time so parts are not impossible to find. From 17 on to the early 20’s the rear ends are notorious for poor metals and gear disintegration. If you can get the serial number, originally located on the base of the front passenger seat facing the door, you...

The cowl is riveted in that area but I don’t recall how. I know it’s riveted to a metal bracket that is attached to the top drivers side false door wood. I cannot remember on the passenger side.

... but how to insure the hardened sleeve is a proper fit on the axle.

Yes! Exactly. If it isn't, the sleeve will wear a groove in the axle.

Constantine's previous post.

One thing often overlooked when removing magnets is keeping the triple gear pins in place. Magnets keep the pins from backing out. Now I personally have not had that happen, I have seen the results.
When ever I remove magnets for someone, I require installation on a retaining ring.

Dan,

I'm not saying that's not a valid concern, but I've got...

Gene,

Can someone post videos of the Hill Climb this Weekend? That sound like it will be super fun

Tim

What a great group of photos!

The issue is that there are at least two different makers of replacement pins, and BOTH are serviceable, one being slightly more pure in roundness than the other.

That said, let's stop for a moment and reflect. The original Ford design called for a 0.002 -0.003 interference fit between the raised pin area and the flywheel. So..yeah a purist...

Saw your group go by in the Huron area several times. Wish I could join you but my car is on the island.
John D.

Put it on the ferry and bring it home!! :lol: :lol:

The beach here is just a stones throw from the Florida Institute of Technology so the scenery can be mixed. Once in a while I take the T down to the beach and the ladies love it, Iv had to tell them to use a little judgment as the seats can get very hot against the missing insulation. From Nov to May the scenery matures greatly. My grandson came...

Back to the top...

Where is it located?

brasscarguy@comcast.net

Sale pending! Thanks MTFCA

Looks like a nice T pickup!

I’m working kinda front to back so I haven’t done (re-done) the bed yet.

This is a neat roadster pickup with California top. Doubt it’s for sale but really unique and fun to look over

PRICE REDUCED TO 235.00 INCLUDING SHIPPING WITHIN THE USA!

PRICE REDUCED 185.00 INCLUDING SHIPPING WITHIN THE USA!

REDUCED TO 325.00 INCLUDING SHIPPING IN THE USA!

All the generator brackets have now been sold and sent to the buyers, Thank you everyone. I still have many generator parts for sale I will be putting another post up in regards to them

The date is confirmed. March 11 1917.

Sorry - I don't have a real good one. Here is a photo from last fall's Manifold Cooker Tour.

IMG_5342.jpg[/attachment IMG_5349.jpg ]

Before you make any changes, count and record the number of “clicks” each jet is from seated. This way you can put it back if you make things worse.

My experience is that they all miss and stumble a bit in low gear… unless you hammer it! Tool little load at too low an rpm with too much fuel. Heat riser may help to correct this. Popping out the...