MTFCA Forum

9E9EB1C3-461F-40A0-BA4F-54517003E8E4.jpeg A1FE30F4-77D8-4C30-A1E0-6B71C8BD0C48.jpeg

I have been asked to participate in a parade that runs every May between our local twin cities. The parade route is about 3 miles and is mostly flat, but there is only one small section that goes uphill over a bridge. I regularly drive my 1914 Touring in 90 degree weather and I don't have any problems with it overheating unless I sit in a long...

No affiliation to vehicle but have his permission to post. Listed as 1920 but clearly a late ‘22 or ‘23 touring car with a 1921 engine. Seller is VERY motivated: woman not included in sale. Call Ryan at 443-562-4258: located in MD. 19A5BEF1-2C40-4BCD-BD60-C4B2DEE4AE0F.jpeg

Last year a good T-buddy of mine, Rich Bingham and myself started looking into the need to find a supplier for Tony Wiltshires timer that uses the round brush. Rich first tried one from this place but it wasn't quite a good fit. Fast forward to January and I picked up the hunt and lo and behold have found the place that actually made them! This is...

Just curious what the advantages/disadvantages to the two types of OF carbs, one with fuel inlet at the top and one with it at the bottom? I know the top fill was the older style.

I recently bought a 1923 T. The wiring is terrible. I have looked at the catalog and have seen the wiring kits for the headlight. I don't see if there is a cover or grommet or rubber piece that goes from the wiring to the headlight. Is there a separate piece? Also, does the kit come with one side or do I need to order two to do both lights? Thanks...

Over the last few months I’ve read number of posts on different builds, restorations, and trips. With current roads and their maintained speed only a dream when the Model T was being built, how well do wheel and axle bearings hold up?

Also kingpins and spindles? Are speedsters stressing these parts when pushing to limits?

Tom
=====

I bought this rim at a swap meet for my Model T shortly after getting into the hobby. I thought it was a T headlight rim until noticing differences with a T rim. This one has a 9-1/8 diameter rather than the 9 diameter on a T headlight rim. There are also 4 steel pads on the outside of the rim, equally spaced. Does anyone know what this is used on?

Nice straight 1926-7 touring body, this is just the body and body parts,
you will need to make 2 patch panels that go behind where the rear fenders mount.
no chassis is included 1500.00 firm, Bob
815-633-7244

WTB new/newer early White floormat. Must be very presentable.
513 Three Seven Eight 4235. Phone or text only please.

When I bought my last T, about 2 1/2 hours from home, the purchase included 3 partially disassembled engines, a pre26 transmission, a few pans, a rear end, some oval gas tanks and some other random bits. I was just getting over surgery and alone when I picked up the car so I left the parts for a later time.

Everything, except the car, had been...

The first year we were in our house (1978) I didn't have car projects ready to work on so I played with some little stuff. I have always liked scale models. It is as easy to get lost in the detail as it is with the big stuff or other interests.
Mini1.jpg
mini2.jpg
Mini3.jpg
So many of us grew up in the era of model planes, trains and...

I don't think the man pushing is doing much good in this situation. I don't see a line between the two Ts so I wonder how they got it out.

Now that my car has some new tires I plan on taking her out a but more. Work is only 12 miles away so I see that happening often in 2023 but I would like to plan on some longer trips than 24 miles round trip. I am sure many of you have great stories and I would love to hear about them.

Ron

FS rear 09 curtain straps, new. Snyders Part number T-3876 LBCE. Does not include brass footman loops. Straps are black with solid brass buckles. 09 does not use D-rings but buckles directly to buggy rail. 35.00
513 three seven eight 4235.

I have 2 Jno Brown 19 head lamp bodies for sale. Believed to be repop spun bodies. Unused. $90 each plus flat rate shipping.

Got this trans in a T parts pickup. I'm thinking it was with this T stuff because they we're looking to adapt it to a T somehow.
Any guesses out there?

Two coil boxes for restoration. Solid boxes, one with the internal parts, the second one just the box and lid. $45.00+ $22.00 ups shipping for the pair. Check or money order. Email me through this site. B1.jpg B2.jpg B3.jpg B4.jpg

New to Model T engine assembly. I have rebuilt other engines in the past and had to align timing marks on the cam and crank gears.
I am in the process of doing a valve job and putting new rings on the pistons for my '26 Coupe. Have read and watched
some videos and it seems that after the valves were installed they just put the pistons in. Did I...

Even though Steve Jelf created some great directions on setting your Model T timing over at ,
I thought I would splurge on the Timing Indicator with LED kit that the vendors supply. It is supposed to make it easy to find the 15 degrees ATDC.

Video Review Link:

Let me know your thoughts here or in the comment section of the video!

I have been working on the wheel rebuild and I got another front hub to replace one of the ones I had that had a spun bearing race. While bead blasting the new one and getting the races out, I noticed that the rough casting was about 1/10th of an inch off center. This made it tough to get to the back side of the race on one side and the rough...

Hi all, could anyone recommend a reputable and affordable car transporter? I already know about freighter Jim, but I’m looking for other options. Looking to ship a T from Kentucky to California. If anyone will happen to be passing by Kentucky to ca let me know and we can work something out. Thanks in advance!

This post is only for dye hard T guys. I've been searching for years for original 9/16 upholstery nails, and have not been successful. They only used these on the end of the binding on early cars possibly until they started using hidem welt. I was using 7/16 until recently. The rest of them are 3/8 .
I sort of scored recently by finding some 1/2...

I have a source for which to acquire the round brush for the TW timer. Naturally the larger the quantity the lower the price. Example...12 would be around $26 ea. but if I can scarf up an order for 24 it is down to a bit under $18, plus tax and shipping. Passing cost on directly. I'm not in the parts business. I just want to keep what I feel is...

I have new parts for a Ruckstell than I am building. I've had the parts since last September and my wife said it's time to put it together.

Good day, I picked up my first T and while it is all original it is missing most of its interior. I have the seats and other misc. items but most of the side and door panels are gone. Anyone know of an original interior, even if not in great shape? Hoping to find a person who restored theirs to new and may have one in the corner of the barn. Thank...

Good day all,
We are attempting to build our EFR (Early Ford Registry) forum viewership, and wish to invite everyone on our MTFCA site to visit. You may register as a guest and post comments or new threads. Anytime you have early brass T era or pre-T info, or questions, please check in over there as well as here.

I’ve noticed over the years...

I have part of a floorboard, 1927 or later written on them, anyone interested in them? They are yours for the cost of shipping.

Hi All,

I have just stripped down the axle on my 1916 tourer. I notice that the half shafts with the half shaft gears attached rock up and down against the spider gears. I'm assuming this shouldn't happen - any idea of possible cause?

Many Thanks
George Hounslow

Here is a NOS Early 09 to 13 Rear Cross member for frame. Not a reproduction or home made copy. The REAL deal. Look at pictures. $500 + shipping. Email me at address in pictures.
D248E34C-ECFB-46EA-B853-144E0B3827E8.jpeg
23CB9566-29F9-437B-AD52-2B71FE0091BD.jpeg
8B94AB51-64FE-47E5-B42E-261AEA221BD4.jpeg...

Does anyone make a high compression head with the Ford script and made is USA cast into it?

For sale: like new spark and gas rods $50 pair. plus shipping
20221013_164847.jpg 20221013_164803.jpg

For sale: One piece cylinder valve cover 21/26 $50 each plus postage
20221010_182220.jpg 20221010_182207.jpg

FOR SALE: Crankshaft counter weights for sale. $75 plus postage 20220726_174038.jpg 20220726_174103.jpg

For sale: hot air pipe 1919/24. good condition other than 2 holes that could be patched. $10 plus postage
20221226_091208 (1).jpg 20221226_091238.jpg 20221226_103356.jpg 20221226_103419 (1).jpg

For sale: 2 emergency brake drums for wood wheels 1926/27 $25 each plus postage
20221127_125353.jpg 20221127_125449.jpg

I virtually don’t know anything about voltage regulators so be gentle ha. This horse has been beaten to death but I’m not sure I’ve read anything on the forum about using a 1940’s-50s automobile voltage regulator on a model T. I’m sure someone will be able to find an old post but thought I’d ask anyway. I’m a glutton for punishment, I have a 49...

I would like to add a panel under the seat of my 22 runabout pickup. This car appears to have been rebuilt by someone made some things up as the went along. The body framing under the seat looks odd to me. I want to make a pan we to go under the seat to give some support to the seat springs but I want to know what the framing should look like...

A question for anyone who has installed a new Stipe cam. Does a new Stipe cam come with the two dowel pins for locating the large timing gear, installed on the cam, out of the box? I called Steve Lang and apparently he had never opened a new cam's box, so he didn't know. I would suspect Stipe doesn't provide them, but before I ordered them, I...

Has anyone seem one of these or have them in their collections?

It looks useful, but did it actually work? I would think NOT to use this when the engine is running as the little ball would be a blur to see I guess.

But could be a bonus when turning over slowly as that would show both TDC and spark firing in one tool.

Untitled.jpg

How much difference is there between the steering columns from 1919 to 1924? Will they interchange?

I have two Ford Model TT's for sale. 1923, and 1926. The '26 is a complete truck, but completely apart. I have all the parts for it. It ran and drove when I took it apart. It has a steel cab with doors. I also have a C cab that could be used instead of the enclosed cab. Also have the bed frame and metal strips. The '23 is missing the front axle...

Like the Doc said, You got it again son!

My problem is with a 1920 engine.

The two different sized crankshaft pulleys are listed for 1920, one at the end and one at the beginning of years they fit.

I used the larger size pulley that should make the fan turn slightly faster!!

I'm wondering if a Gates 820 flat black belt was intended for use on...

Can anyone shed some light on whether to use the original one I have or switch over to a solid state one.
A description of the original one could result in generator failure and the solid state ones sound like they
are more reliable. I found them on Snyders web site and the cost is a lot less that replacing a generator
if the relay gets stuck....

FS: Pair of 1914 Rear Touring Roadster Fenders. I believe these fenders are reproduction, very nice. Comes with one fender eye bolt. Price $475. plus shipping. Call or text (248) 894-75fiveone. Thanks Walt

During a recent outing, we came across a T touring sitting in a barn yard. The older owner has been ill for about three years. A club member bought the barn yard car. The family is selling the remainder of the collection. There are 3 cars left, commercial hack, 26 touring and a 21 roadster pick up with wood bed. All cars have been sitting in a dry...

Hello. I'm a new member and thought I'd say hello. I have just bought my first Model T (1923 pickup conversion). I'm looking forward to learning from people on this site.

For Sale: Pair of Electric Cowl Lights - 1920 and later . Very nice. $350.00 plus shipping.

Carter updraft carburetor. This has been in one of my parts buckets for about 30 years. I don't know anything about it. Missing the bowl and float. If the speedster guys can use this carb email me or post something here. C1.jpg C4.jpg C2.jpg C3.jpg

I received a new radiator for my T and installed it. I have only driven car since maybe 30 miles or so. Recently I was looking under the hood on left side and discovered the overflow tube broke loose and just hanging from the tank on top. Also the old radiator had a couple ears toward the top where a couple screws went though the shell to support...

Here is an original radial engine radiator cap ornament. The solid aluminum blade is a replacement. It needs to be drilled for a shaft, and an appropriate sized bearing inserted inside the radial engine for the propellor shaft to spin on. Easy project for the creative tinker. These are very hard to find, the blades are not being reproduced in...

We are in the planning stages of putting together a model T tour in Eastern Europe, with the antique automobile and model T club of Hungary in September of 2024.
Gathering information to find out if anyone would be interested in a 12 day tour that includes Budapest and Vienna with their model T. We would be going through a lot of countryside,...

I’ll be putting my ‘11 up for sale in a couple of months, probably late March or early April; I’m just posting now as a heads up. It’s a great car, more accurate and complete than most, and a strong runner. I need some time to get it out for more pictures, that’s the main reason for the delay. Feel free to email if your interested. I’m not looking...

Know you guys have other stuff in your collection so thought I would ask here too.
Looking for the elbow(s?) that holds the choke and is mounted to main body of a made for Dodge Brothers Stromberg OD-1 carb. The mounting holes would be approximately 1-7/8 center to center. I was hoping the part from my OS-1 would fit but was too wide. While there...

Pair of wooden wheels with 1926-1927 Drums and Hubs with 15 tires. $200 for the pair.

thumbnail_IMG_1760.jpg
thumbnail_IMG_1759.jpg
thumbnail_IMG_1758.jpg
thumbnail_IMG_1757.jpg
thumbnail_IMG_1756.jpg

I wanted to reuse the original rain gutters from my coupe, but I have not been able to separate the two pieces. These are shown in the first three photos. I have purchased new aluminum gutters shown in the last two photos.

The primary piece of the original gutter was held in place by tacks. I appears to me that the secondary piece, witch covers...

Theses are new Gilbert lights . Perfect
$1000.00 plus shipping
Tom Butterworth
772-475-9142

Small dent in the bottom and missing the rim and screen. $50.00+$17.00 usps shipping. Check or money order. Email me through this site. H1.jpg H2.jpg H3.jpg H4.jpg

Free to good home...Atwood Castle 104A brass amp parts. No glass, fonts, or burners...some usable chimney caps, housings,reflectors, faceted jewels, doors. 2 boxes of parts.
You pay shipping. If not spoken for by 2,5,2023 will be trashed. 513 Three Seven Eight 4235. Phone or Text only please.

Looking for a good complete rebuildable core Model B carburetor 1932 and intake manifold. There's a number of the them on Ebay, prefer to buy from a club member and hope to avoid the overpriced shipping and sales tax. Thanks

What is the contact number for the guy that makes the floorboards?

25 windshield stanchions, extra part from a recent restoration, epoxy primed. $65.00+$22.00 shipping. Check or money order. Email me through this site. S1.jpg S2.jpg S3.jpg S4.jpg

2 steel and 2 cast aluminum. $40.00 plus $12.00 priority mail. Personal check with hold. NO PAYPAL.
Bob Giles
Johnstown, Pa.

Excellent narrow neck pan just professionally straightened and ready to be installed. I had it restored and straightened and then decided to change to a 4 dip for access to the forth rod. Can send photos of inside and out.

$250 plus shipping expenses, can possibly get it to Tulare for the swap meet.

frontyboy

2ho69191949(Text)

I have 2 NOS Ford Steering Controls in the original boxes for sale. One of them is nickel plated and the other is black Japan enamel painted. The black one will be correct on brass era and also nickel era cars. The nickel one is most correct for 1917 to 1927 cars. They both will fit all years of Ts and TTs. These do actually give a little help to...

Wanted, cast trailer hitch, same as the style shown in the photo.

Photo borrowed from a previous post.

Thank you in advance.

Andy

1926-27 Model T Windshield Stanchions. Very nice matched pair. Need to be cleaned and painted. $185.00 + Shipping

I've only seen a couple of these special wrenches - sorry I don't have a pic. Works like a brace and bit. Anyone own one of them and do they actually work?

1910-11 Kingston Five Ball carb in good shape, from my Grandfathers prize winning 1910 Model T with all brass accoutrements.

More pictures available upon request.
Located in Mt. Airy Maryland.
$2300

Has any one done a speedster front suspension using a 2 drop front axle, with the early style perches, a double wishbone (above and below the axle) mounted to the engine pan (not on the outside of the frame) , reverse eye spring and 26-27 spindles? If so, how did you set-up the tie rod and drag link?

Family home movies. (Not mine) 1929 Franklin, Lincoln Highway road scenes, small towns, landmarks, steam trains, motor court cabins. If you have some time on a cold winters day it's a good window into what auto travel was like for one family in 1929-30.

Looking for an '09 or '10 engine head without issues . Please email me so I can see photos. Thanks

This is the preferred head
1910 head with raised mold marks -pic1.jpg
--
--
Second choice but strong contender

I purchased a reproduction Steven's axle repair frame a while back and I am getting ready to use it. Upon inspection I see the two holes are misaligned. I don't think I can use it as is for fear the repair bushings won't line up enough to allow the spindle bolt to pass through the repaired axle and thread at the bottom. It's not just a matter of...

Still searching for top irons or top for 25 Roadster.....anybody have any laying around?

This is probably a trick that many of you know but I'm posting it because it was new to me and worked well. It may help someone else.

I acquired a replacement hub and couldn't get a hub cap to thread onto it.

20230126_205152.jpg

The threads were a bit mangled.

20230126_143005.jpg

One of the club members suggested I use a wheel puller,...

For Sale: Peining Hammer $225. with free shipping in US only. Head diameter measures 1.183 inches. I don't see any markings on the tool. The ad below is for a K.R. Wilson tool. Call or text (248) 894-75fiveone. Thanks, Walt

The front camshaft bearing (notched style ) needs to be babbitted and bored.
Also the front camshaft journal and thrust face also needs to be touched up by
grinding.
Can anyone tell me what the original length was so that I can determine what
the new reworked length would be ?

Thank You

John

I am going through hundrens of T hinges and ran across this one, any ideas what its for? Bob

An extremely nice, dent free and rust free running board tool box. New single stage black paint. 21” long
$130.00 plus freight
Text: 423.237.8846
Email: ltlapatka@gmail.com

SOLD -- High Speed Ruxstell Rear End for TT Truck. Completely rebuilt with new bull gear and worm gear set. $2000. Gears were made by Mike Hartmann, Mike's Machine Shop in Arkansas. Photos available on request. I can deliver at Chickasha in March.

I'm looking for a Ruckstell rear end that I could rebuild.
I prefer a 26/27 or even a left side ruckstell housing. I would also consider earlier ruckstell. Like to pickup at Chickasha pre war meet. Please email me or you can text to 316 640 5026.

Thanks
Steve Bender

For sale wrench marked 5Z-815 this is a crankshaft center bearing bolt wrench per the tool list asking $70.00 shipped to your location call Matt 503-824-2681

1911 - 1912 to early 1913 Model T Frame - Very good condition. Is sandblasted, primed and painted. Has rear fender brackets on it. The running board support rods are also there. More photos available.
Can deliver to Chickasha, Ok or Luray, VA swap meets in March and May.
$1200.00 or OBO.

One says ford b t7258 the other doesn't. They are the same though. 30.00 plus shipping. ctleonard64@gmail.com IMG_20230131_125337461.jpg IMG_20230131_125322219.jpg

I am looking for an exhaust cutout for an exhaust whistle on my 1922. I would prefer an original cast iron one in decent shape to go on a car.

Wanted 1 side lamp bracket like pictured. meyre14t@yahoo.com

From my grandfathers prize winning 1909 touring car toolkit and brass era car colletion.

3x NIB Champions, these look to be repros.
2x Used Champions, these look to be repros.
1x used champion X (update found the box)
4X antique plugs, all look to be used.

$250 For everything + postage
UPDATE : Price cut, $120 + postage

I can get more...

Have a set of new floorboards I purchased at Luray last year that I don’t need anymore. Made by Jonathan Anderson for an ‘11 Torpedo. Would like to get back what I paid for them, $210. Willing to ship domestically at my expense.

Feel free to reach out.
2013067112

Thanks,
Austin

Nice shape, float looks plenty good enough to reseal and use, $85, domestic shipping $10.

Thank you, I found 3 more types can anyone identify? thank you, Bob
B looks it might have a brass cover

Sure seems like one of those easy tasks to check off your list in short order on a rainy day. Well, it isn’t. I did one, for the first time, this afternoon, and must say that it took a good 50% of my mechanical ingenuity along with about 4 hours of my afternoon to accomplish. The result was perfect, but man, I never expected to incorporate the...

Hello All, I am restoring my Model T 1914 headlights. Would anyone know the shade of back paint I should be painting the inside of the headlight housing (glossy black, satin black, flat back, jet black) ?? Bob