MTFCA Forum

Does anyone know if this page is actually connected to the club or not?

Got to wonder about it because they don't list actual names for administrators, just the page name itself.

I'm converting a 1926 T roadster to a slide in pick up box. I'm wondering if anyone has tips (experience) for removing the turtle deck/trunk of the roadster body.

Thanks, Mike

The weather was perfect for a drive with some speedster friends. IMG_5813.jpeg

I have 0 sets left of 4 new in unopened K-W points.
$105 per set shipped to the lower 48.
PayPal friends and family prefered or good check.

Hello everyone,
I'm trying to find a picture of the perch nut end of a wishbone that uses the tapered nuts. Back story... I still have a death wobble at 20mph after changing king pins, king pin bushings , perch bushings and shackles, steering bushing, tie rod bushings, wishbone cap, pitman arm and tie rod ball end. Everything is nice and tight but...

Just wondering if it is behind schedule OR did I not get my copy? I'm not complaining, just wondering. ;)

Model TT, probably 1924, stake-bed, C-cab
Rear wheels are solid rubber, rim is steel. The wood felloes have some dry rot. Can they be replaced when the tire is solid rubber? Spokes too?

 
Here is a link to a short video for a unique method of handling and
shipping a HCCT (Hand Crank Coil Tester).

It was designed by Mark Gember (the guy in the video).

Anyone want these ? 5.00 each, some are NOS. Plus shipping. kdmks AT att.net.

I found sn original T screwdriver in a second hsnd tool store recently. It has been well hammered on the handle end and the handle is a bit short as a result but it is still recognisable, so into my 1912 van tool roll it goes. That liberates the one I fitted with a new handle made to the Ford print.
20260314_150236.jpg
Allan from down under.

Get it for your grandkids! Get it for yourself!
To be issued in March.

LEGO 11376 Ford Model T celebrates the revolutionary automobile - Jay's Brick Blog

First Brands appears to be filing for Chapter 11 and state that Autolite is one of
the brands to be discarded. I called around for Autolite 3095 and no one had any
in stock. I was able to order some mail order, but I am wondering what will be
available after those are gone. Just Champion X or do some of you use something
else?

it is getting to be time to start planning our springtime auto. activities ... i spoke with Kevin Hammock this week regarding any changes in the Duncan swapmeet in March ... the only change is BIGGER ... the 2 north buildings are sold out and the building that was under construction last year is completed and will house an additional 100 plus...

Looking for a Stewart speedometer S bracket that clams onto the speedometer drive (swivel)
Thanks
Mike

mikebird@lifeattheridge.net

Heavy Case Muncie - Gears look very, very good with exception of underdrive gear on lower shaft, which has 4-5 teeth in a row damaged. Photo of damage included. Everything spins nice. Under-Direct-Over-Reverse. Roughly 2:1 U, 1:1 D, and 0.73:1 O. Were used in Ts and TTs. I don't have the couplers. Pick up south of Kansas City or can deliver to...

Unpolished cast aluminum. Vendors no longer carry the traditional finned style. Full disclosure, it was made from a cast running board step plate. $135 and that includes shipping in the CONUS.
32393BF8-8C7E-4F4D-9C23-71A405CF2E3A_1_201_a.jpeg
C5CA4CEE-3D6A-4B3B-A7FB-D00852BDB039_1_201_a.jpeg
0AC802F5-F1B3-432C-9586-116258F23038_1_201_a.jpeg

WTB
Looking for 4 sets of new KW points for 1922 ford t.
Thanks Larry

Do you have to constantly fiddle with the ignition coils to keep your Model T car running properly? I can assure you this is not normal operation for a Model T Ford. Unreliable engine performance, hard starting and poor idling are commonly caused by poorly operating or adjusted ignition coils.
Over the last 35 years I have rebuilt over 26,000...

Hello.

I recently bought a fulton whistle over ebay. The whistle is working and in good shape, but the cutout is totally worn out and there's no sense in trying to restore it. So I was looking for a proper alternative part and found the perfect solution at Texas-T-parts. But unfortunately they don't answer my email for an estimation of shipping...

I am going to part out my 1913 Roadster project. The body is going to be first to go. Very nice body and top irons/bows. Came from an auction in Ind years ago. $4500 pickup here. It Email me by forum. Dan
IMG_5236.jpeg
IMG_5253.jpeg
IMG_5242.jpeg
IMG_5244.jpeg

For sale is three running board luggage racks. One short one and two tall ones. All three work as they should. The brackets on the two taller ones are just a little bit different. $60 for the short one, $80 each for the other two, plus shipping to the lower 48 for all three.The running board is NOT included. Best way to reach me is either a text...

Has anyone ever seen one? Or own one? Have one for sale even?

I am looking for ideas to build and install a lefthand Ruckstell shifter on a 26-27? The vendors say that the one that they sell will not work on 26-27's.

Selling this as a lot $15 plus shipping.
mikebird@lifeattheridge.net
Thanks!

IMG_4788.jpeg
IMG_4789.jpeg
IMG_4790.jpeg
IMG_4791.jpeg
IMG_4792.jpeg

Hello, does anyone know what chemicals would you use to clean the wood in a coil box? Basically, what a professional wood worker would use which will not deform or compromise the wood integrity?

Again thanks.

Looking for a Stewart Cast Road Gear. Block lettering No. 22
Thanks Mike

mikebird@lifeattheridge.net

Found one. Thanks for all those who emailed me.

A nice, large pair of electric headlights from about 1912 to 1915ish. These are probably too big for a Model T but? They are approximately 12 in diameter, 9 length and have 9 center to center for the mounting holes. These have convex lenses and single sockets. Brass bodies with nickel/brass rims. Very nice as found original condition. A great pair...

i am starting this post in possibly the wrong section BUT ... the Duncan,Ok. swapmeet is coming up in March and i am attending to sell as well as purchase some parts for my projects ... i am WANTING TO BUY ...a windshield frame for a 1931 Murry body model A 4dr., Masonic items from the 1900-1930 era , and 4 cyl. Dodge Brothers items ,particularly...

IMG_5314.jpeg IMG_5293.jpeg IMG_5327.jpeg IMG_5298.jpeg

Perry Auto Lock Accessory for the Model T steering column. Very nice shape, It comes with the original Yale keys and it works very nice. Great item for a speedster or period correct accessory to add to your model T. Great conversation piece.
$200 plus shipping

mikebird@lifeattheridge.net

IMG_4746 2.jpeg
IMG_4747 2.jpeg
IMG_4748 2.jpeg

For Sale is a rare 1926 - 1927 Kingston Regenerator Carburetor. Most likely needs to be rebuilt. $200.00 plus shipping Lang’s 1-800-872-7871

Burners and parts, all plus shipping. kdmks@att.net.

A real nice 9 diameter spot lamp from B&L Company in NY and is Number 107. A very good lamp for medium or large brass car. Nice glass reflector, burner, handle, tag etc. Price is 350.00 including shipping via FedEx Ground with insurance in the USA. I don't check messages here so call me directly at 734-730-4274 or email directly at...

I have 6 888 Schrader stems. The threads are pretty nice. Only to of them are a little bit rubbed down on one side. All thread very nice still. These are just a little shorter than the 777s but still work well with the dust covers and rim nuts. $100 plus shipping.

IMG_4288.jpeg IMG_4290.jpeg

Wanted: original 1914 Ford coil box lid

I purchased a new repro lid for my 1914 T awhile back. When I installed the coils, the lid would not close all the way. Now I have to drive with the coil box lid off. I am using original metal top coils. I set the metal top coils along side of a later ford coil and the metal top coil is much taller then the...

For Sale are 2 tools used when removing and installing the Driveshaft bushing for Model A’s and V8 Fords. $250.00 plus shipping Lang’s 1-800-872-7871

For Sale is an original 5Z-204 Ford Script Exhaust Pack Nut Wrench. $100.00 plus shipping. Lang’s 1-800-872-7871

For Sale is a nice 1910 - 1913 2 piece driveshaft housing, no bump spool, ball and collar. $550.00 plus shipping Lang’s 1-800-872-7871

For Sale is a usable low head for 1913-18 T’s. One spark plug thread isn’t as good as the others. A crack is developing on the water outlet flange. $35.00 plus shipping. Lang’s 1-800-872-7871

Zero throttle shaft wear
main jet and compensator jet access bolts have a little bit of wrench marks but are not objectionable
fuel coupling has a new retaining bolt (old one had some pliers marks - why on earth do people do that???)
no cracks in brass body
venturi is complete - I doubt it would survive removal and suggest it be left alone...

The title says it all. I have new made visor frames and brackets for 23-25 closed cars. I don't think these are available in catalogs. I used an original as the pattern. The frame is a little heavier and the stock for the brackets had to be custom made before the brackets could be made. These are very nice with all holes drilled to match the...

I am looking for the windshield garnish with swing arm bracket attached, for a 1923 Fordor Sedan. I believe the 1924 & 1925 models used the same garnish. There are some photos on this forum from a few years ago, showing exactly what I need. But have not yet been able to reach the gentleman that posted the photos. Any help would be greatly...

Here in St. Louis, The Model T Club of Greater St. Louis, is having our annual swap meet May 3rd.
I don’t know how many years this has gone on for us, but I attended many times before joining the club, going back well over 25 years ago.
We have been at this location for a few years now.
Last year highway construction impacted our turnout, but as...

For sale: I have 2 fatman steering wheels. 1st one is a Bauer and the 2nd one is a Spencer. Wood is very good condition. Have not done any cleaning or polishing so you can make it what you want. Have a key for the Spencer. They are $500 each plus postage.
20250821_230246.jpg 20250821_230040.jpg 20250821_230013.jpg 20250821_233019.jpg...

20250324_141159.jpg 20250322_184948.jpg 20250322_184855.jpg

For sale: Hayes rim $100 plus shipping

For sale: Ford script bendix puller 5Z323 very good condition
$95 plus postage
20260201_220640.jpg 20260201_220659.jpg

IMG_8587.jpeg I just got the head back the machine shop this week. The head got 8 new valves, 2 new valve guides and 6 bronze inserts. There is a serial number on the front of the head and it is 1077 X. There is freeze plug on the top of the head that has some number but are pretty hard to read
Fitz

Anyone know what is the original wood in a 26/7 coil box?

Thanks in advance!
John.

1911-12 TW trade mark front axle with early no oil hole spring perches. $200 plus shipping. kdmks AT att.net.

WTB Driver side REAR Fender for 1915 or 1916 ONLY. A curved fender that is flat on the top with no crown between the beads. I need it for a Touring Car.
Contact Gator Gould, Monroeville, AL. Email me here on Forum.

I need a modern title for a 1915 or earlier T, so I can register my speedster. Joe at 650-279-6609

IMG_5245.jpeg IMG_4403.jpeg IMG_5302.jpeg IMG_5288.jpeg

Has anyone received the Jan-Feb issue of the Vintage Ford?

It's that time of year! Time to dust off the ole speedster and head for Santa Clara Valley for the Santa Clara Valley Model T Ford Club 55th Annual Endurance Run & Lowland Tour! And don't forget about our Veterans. We haven't! In addition to our annual endurance run and lowland tour, we are hosting another Veterans Appreciation Car Show at the VA...

For sale: Ford script wire wheel hub caps all for $65 plus postage
20241027_101908.jpg

Looking for a Model T service provider in SE Wisconsin. I have a 23 Model T Tudor that I would like to have the engine tuned up.
John Cleary

Model T Speedster Project For Sale

-Very well built steel body with wire edge, wood firewall and floor.

-Older, new reproduction gas tank, never had a hole cut for a filler neck.

-1926-27 engine and transmission, turns with crank.

-1921-1925 frame and axles.

-Older, used high radiator and shell.

-Wheels and tires are in rough shape, just...

This is the last in this series, and is perhaps the most unique in overall design having a folded center support wall, vs. the traditional vertical. The six center holes are spade-shaped vs. oval or circular. The lugs are formed from semi circular designs rather than the previous curved step outs.

T_725_B3 clutch drum preview_1.jpg...

If you like a deep, steam train whistle and a high pitched whistle, here it is from an old garage with neat brass parts. There are two Aermore whistles, marked No.0 (smaller)and No. 00 (larger) and a Fulton cutout which can be used with either. The cutout has double butterflies that work and the enter/exhaust pipe inlet is threaded. The two...

This Budd knock-off cap can be used on Model T or Overland depending on the emblem. At one time, the Ford emblems were reproduced. Of course, you can just remove the Overland emblem. This is a very nice cap. Good threads, latch, etc. This has not been hammered to death. Hard to find in this condition. Price is 200.00 including shipping via FedEx...

Any idea on this wheel

20220721_195820.jpg 20220721_195926.jpg

For sale: brass hubcaps. $45 plus shipping for all 3

I am rebuilding my driveline and working on the driveshaft now. In front of the pinion gear is a roller bearing. I don't understand how that bearing is lubricated. Should I install a zerk?
Campbell Tellman
1916 Ford Touring
Beaufort, NC

For Sale are a pair of Bill Bohlan’s Laurel Style Front Lowering Brackets. They are no longer being made.
$250.00 plus shipping Lang’s 1-800-872-7871

Henry Ford acquired A. Y. Malcomson and some smaller investors stock prior to 1907. As a result, he held a significant majority in the company named for him, and for all intents and purposes he was in control.

Here is what he wrote about the six cylinder v. the four cylinder motor at that time.

IMG_4423.jpeg

IMG_4424.jpeg

IMG_4416.jpeg

An original round gas tank. This was stored in dry storage in an attic in the 1960's Very nice no rust out or pin holes. This has the off center drain so it's not an early 12. It had a brass sediment bulb so definitely 12-15, but can be used all the way up to 1920.

$200 plus shipping.
I can ship this very reasonably. I just shipped a 1910 tank...

Pretty nice original Ford script tail gate $250 plus shipping. kdmks AT att.net.

FOR SALE: Front Fenders for 1926-7 Model T. One is a New Rootieb Fender and the other is an original. Selling as a PAIR. Asking $900. Contact Gator Gould, AL. PM or email here on the MTFCA Classifieds Website.

1923 Ford Model T 3-Door Touring Car for sale. Car is complete and running. It has a New gas tank and new carburetor. Also, it has been converted to 12 Volt System with a Distributor. The car is a very good driver and is very presentable as is. The interior is very good and the top is as well. It has side curtains .

Asking $10,500. Serious...

I have a TT chassis with a Ruckstell rear end that needs a new home. I cant take pictures as it is surrounded by too much stuff. The wheels roll but are no good. No sheet metal, body, running boards, engine, lights, steering column or firewall. I would consider delivering to Luray in May if you make a nonrefundable deposit. $1000

SOLD to Ed! Thank you. Nice original pair of burner bases and brass elbows. Good threads. 100.00 including shipping via FedEx Ground within the USA. I don't check messages here but call me at 734-730-4274 or email directly at motoringicons@hotmail.com Thanks and Happy Motoring!

Well, they still exist out there! This one is for sale in Ohura, New Zealand. That happens to be a very small town in an out of the way place, but the dealership still shows signs of what it once was. The town was founded on coal, long shut down, and now supports a small rural population with around 160 residents today. The remains of the railway...

1915/16 Model T Roadster Front Seat Cushion NEW
This is a new, never installed front seat cushion for a 1915/16 Model T Roadster. The material is vinyl. $450 plus shipping. Any questions feel free to send me a msg. Thanks!

IMG_4769.jpeg
IMG_4770.jpeg

Looking at the 26-27 roadster body that just came up in the classifieds,
but
it is in Chippewa Falls, WI and I am in Atascadero, CA (central CA coast 93422),

Any chance someone would be able to transport or know of someone making the trip out west?

This is my dream T since I was a kid hanging out in my grandpa's shop,
I have seen others over the...

I have 6” and 1 7” glass headlight reflectors for sale. $100 each. Plus shipping. kdmks AT att.net.

Looking at the 26-27 roadster body that just came up in the classifieds,
but
it is in Chippewa Falls, WI and I am in Atascadero, CA (central CA coast 93422),

Any chance someone would be able to transport or know of someone making the trip out west?

This is my dream T since I was a kid hanging out in my grandpa's shop,
I have seen others over the...

For sale, 26-7 roadster body with turtledeck, turtledeck floor, gas tank with straps ( nickel size hole in bottom ) No trunk lid. $1700 firm

DSCN2010.JPG DSCN2011.JPG DSCN2013.JPG

Located in No. Illinois, I am hunting for a couple of 30x3 used but drivable tires. White, black, gray it doesn't matter.

Does anyone have a couple collecting dust?

Thanks,
Jim in Oswego

Here is the 3rd major version of the Model T/TT transmission Clutch Drum. Noticeably thicker around perimeter, with only 2 holes, vs. the previous 6. While researching this drum, I have found photos showing the Ford script to be on the front side as well as the back side.

T_725_B2 clutch drum preview_1.jpg

This is first drum used in...

I need to clean up some threads on a 1910 sediment bulb. What is the thread size for the hole where the fuel shut off valve screws into? I know the shut off valves had two different size threads on each side that almost look identical. Thanks!
Mike

I have 4 30X3.5” tires with cracks. 2 Firestone H
And 2 Wards Riverside. The Wards tires are only a couple years old but were cracked all over. Corker and Snyder’s stepped up and replaced them (see pics) very grateful to them both !
I can get pics of the Firestones if needed, but they all have good tread, just cracked and not roadworthy. $20ea and...

I have one pair and 3 other single pieces.
$65 for all of them including shipping to USA 48
Please call or text me at 33zero 3nine one nine zero 62 Thanks Dave

Wood is solid also…$100 including shipping to the 48 states
33zero 3nine one nine zero 62 is the best contact for me, thanks Dave

I have several ring gears, pinion gears a a couple diffs and gears…
Ring gears have a little wear but not much
$80ea including shipping to the 48 states

Pinion gears, 2 are Ford script and one is not.
Good shape. $65ea for the Ford gears and $55 for the other one, including shipping.

2 diffs and one spider. One diff w/ring gear.
Spider, $45...

With or without the distributor is ok but I would like one with the toggle & levers. I'm looking for the type with the distributor on the front, not the magneto on the side.

Located in CA but happy to pay shipping.

Was cleaning up an area in the garage today and came across an old Craftsman hand carry tool box. Opened it up and sat down and went thru it. Going thru the tools in it was like visiting with old friends I had not seen in years. Some of these tools had helped me make a living for years and it was nice to handle them again and put them into another...

This morning while checking the tire pressure I found a screw in my Blockley front tire. I guess it didn't make to the tube as the still had good air pressure and who knows how long its been in there. It renewed my faith in the Blockley tires and tubes. I bought these tires a couple years ago before all the issues with shipping. I'm going to order...

I’ve seen many strange and interesting accessories, but this takes the cake for the silliest. I wonder if one survived?

“Lemuel Bosco of Akron, Ohio, spent $5 for an antitheft device that was supposed to lock the Splitdorf ignition switch of his car, but it didn't stop a thief. He broke it off and took Bosco's Mercer for a joyride. The cops found...

Check this out. Seems like they're made for reaming out triple gear bushings. But just doesn't make sense. Anyone know what they're designed for? Found 'em on eBay, pretty cheap. I already had the Wilson reamer, which I tested, and iit fits inside the fixture bores.
20260307_175852.jpg

20240618_170139.jpg

For sale: hub puller in good condition $50 plus postage
20260107_163458 - Copy.jpg 20260311_190101.jpg

This is a NOS 1914 touring top and rear curtain. It is of vinyl construction. This is brand new never been installed. It was made by Hinson MFG Company in Iowa. They were a large textile mfg company in WWII. They provided interior/tops for Model T's in the 60-70's. These pieces were stored away in climate controlled environment and were never...