MTFCA Forum

Completely disassembled and cleaned, new float, float valve, venturi, choke spring, reconditioned spray needle and spray nozzle, throttle shaft bushing installed, test run. $325 postpaid to continental USA email: wlkma9@gmail.com

Some KW. Some Ford. Only $50 Gently used. + free delivery lower 48. gwhouse731(at)gmail(dot)com

I bought these unfinished from a gent. I'm not going to use them just wanting my money of them 100$ plus s&h they are stainless need finishing what you see is what I have

Brand New 6 Volt Model T Starter Field Coils and everything needed to install them.
$59 + shipping (usually under $10) - Compare at OVER $100 for the Wilsons

These are also Epoxy dipped with plastic insulators between the fields and will likely last well over 100 years.
Note - the post is Silver Soldered and pre-installed

I have ONE 6v starter I built that a customer ended up not needing that I can ship right now - no waiting.

Best Possible quality rebuild.
PRICE DROP! $325!!

Now that I make literally every part in these units except the housing and the armatures, I can pass some savings on to everyone.

New field coils with silver soldered post (yes, I now make...

FS. 09/10 double twist brass horn with cover. New screen, repro reed and repro brass adapter tube. Tube wrap is correct oval vs round and has horizontal inlet vs angled. Excellent show condition,, has no mfr. stamped name, otherwise identical to Rubes or Nonpariel. $700.00 plus freight.
Scott. Text or call 513 three seven eight 4235 or...

For sale EMCO cast iron muffler with cutout. EMCO model F muffler and cutout was painted with hi temp header paint. Cutout valve operates smoothly, lubricated with anti-seize hi-temp paste. Inlet measures 2-inches inside diameter and outlet measures 1-5/8 inch inside diameter. Muffler has two mounting screw. Price $250. plus shipping. Call or text...

For Sale Cantrell Rear Axle Outer Sleeve Puller. Threads are in good shape and lever for sleeve engagement operates smoothly. Small lever operates pin to engage sleeve, center screw pushes against axle to extract sleeve. Tool is lightly marked Cantrell on side. Price $225. plus shipping. Call or text (248) 894-75fiveone. Thanks, Walt

For sale EKERN rear axle emergency repair axle fixture. Fixture axle rotates smoothly And threads are in great shape. Grease cup was filled with synthetic grease for long life. Clamps onto backing plate. Used as a temporary fix to get you home after an axle break. Works on small backing plate axles only. Price $175. plus shipping. Call or text...

For sale early left and right headlight forks marked (DB) Dodge bros. and raised part numbers. Forks are in nice condition with good threads and nuts. Price $250 plus shipping. Call or text (248) 894-75fiveone. Thanks, Walt

FS Fork mount headlights

$100 plus shipping

For Sale a pair of Essex headlights.

$200 plus shipping

Interesting design accessory Horn that has a “push lever” to make a loud signal. Brass bell and black painted housing with bracket that mounts on the Fake door of a touring or roadster body. $250.00 plus shipping. Lang’s 1-800-872-7871

Newly manufactured and fully machined axle housings Silicon steel cast centres pressed into original tubes and backing plates. All internals fit these perfectly machined hidings. No rivet leaks no droop ready to accept your internals
Machined to factory specs This is the last available pair. No further runs. Call for details
705 828 5405 Eric...

Pat’d Dec 22 1914 carburetor completely disassembled and cleaned, new float, float valve, venturi, choke spring, reconditioned spray needle and spray nozzle, throttle shaft bushing installed, test run. $235 postpaid to continental USA email: wlkma9@gmail.com

Found a mate to the left one so have a pair to sell $55 + shipping. IMG_3780.jpg IMG_3781.jpg
Craig.

No longer these windshield stanchions $ 45 + shipping IMG_3782.jpg IMG_3783.jpg
Craig.

Windshield frame mount spot light, Good glass, fare mirror, switch & bulb work. $60 + shipping IMG_3790.jpg IMG_3791.jpg IMG_3792.jpg
Craig.

Pr 1913-17. Original Cast muffler ends clean with no cracks $75 or
1918-27 Original cast muffler ends. Clean no cracks $75 pr
Pair restored front fender irons 1916-25
$50 pr
Eric Edwards. 795 828 5405

1909-10 headlamp forks sidelight brackets and dash to frame brackets. All recast in bronze $250 for all 6 pieces
Also 1909-10 front seat top pivots mint originals $125 post included
Eric Edwards 705 828 5405

1909-10 headlamp forks sidelight brackets and dash to frame brackets. All recast in bronze $250 for all 6 pieces
Also 1909-10 front seat top pivots mint originals $125 post included
Eric Edwards 705 828 5405

For sale, one 1909 Atwood Castle Brass headlight model number 84. $400 plus shipping to lower 48.Best way to reach me is through text message, my number is 419-217-8884.

Reproduction 1911 - 1914 steel Hood Former Sold. plus shipping. New cost is $230.00. Lang’s 1-800-872-7871

Still on the lookout for a 2 Cylinder Ford project if you know of anything? Unrestored or an old, tired restoration etc.

Please send me a private message if you can help, or with any leads.

Thanks 🙏

Nice looking Waltham dash clock. Came with some T parts that I bought. I don’t know anything about clocks so I didn’t want to mess with it and take the chance of damaging it.
The face measures about 3.25” diameter.

$75 plus shipping in the U.S.

IMG_8261.jpeg

IMG_8262.jpeg

IMG_8263.jpeg

Very nice Victor Top Tank for 1909-12 cars
No cracks or splits minor imperfections. Very nice $300 USD Eric Edwards

New Repriduction quadrant $35.00
Eric Edwards 705 828 5405

Brass Toquet carburetor. Appears complete. Throttle and choke are free. Interesting design and seems like a pretty basic carburetor with a straight through design. The only things I could find wrong with it are the choke spring is broken and the threads on the fuel bowl inlet aren’t the prettiest but could use a little touch up with a thread file....

One Ford Script speedo head
One Stewart speedo Hess.
Both need service. $100 ea
Eric Edwards. 705 828 5405

I have a pair of New 13-15 hubcaps.
Also 3 matching new Made in USA caps. $20 each
Eric Edwards. 705 828 5405

:mrgreen: :mrgreen: :mrgreen: Original brass top tank no cracks or splits. A few very small marks but really nice. $300 pics available
Eric Edwards 705 828 5405

Looking for a pinion gear for my 1918 Maxwell 25 if anyone has a spare to sell.

WTB 4 1910 JB coil box bottom electrical clips that the coil plugs into on the bottom of the box. New or used. Thanks Ray

1926 Ford Mdl. T Running Boards - L&R Both Boards Good Condition- $200.00 together

Nice clean crack free trans cover
No pedals $125.
Eric Edwards. 705 828 5405

1918 Non starter block Made in Canada
Also rRHD
transmission cover with pedals
Eric Edwards. 705 828 5405

IMG_7696.png New silicon steel centres pressed into original tubes and backing plates. Perfectly machined. No rivet leaks or drooping. Workmanship guaranteed. Immediate delivery. Last pair available no further runs.
$2750 1911-12.
1908-9 no rivet with smooth new backing plates and tubes $4250
Eric Edwards 705 828 5405

Hi…..any out there?

New Silicon steel castings machined to standard specs pressed into original tubes and backing plates. No rivet leaks no drooping axles
Accepts all Ford internals
Immediate delivery only one set available
$2750 USD. Eric Edwards
705 828 5405

Here is a speedometer mount that came off a straight spindle arm. Don’t see a name on it. $20 + shipping. See pictures. Email me by forum. Dan
IMG_4788.jpeg
IMG_4789.jpeg
IMG_4790.jpeg

… for your project. Excellent 2 piece frames and glass channels are 39” long and 21” high. Plate glass removed (recommended) upon request and 2 frames shipped for only $75 + FedEx.
gwhouse731(at)gmail(dot)com

For sale: starter bendix parts $200 plus postage
over $500 plus some not available

20250701_162043.jpg 20250701_162018.jpg

For Sale model A tool kit.

$135 includes shipping

A tools.jpg

For Sale, misc nuts, bolts and hardware, more pictures, More of the previous add, $80.00 + shipping
image000002 (3)lb3.jpg
7.jpg
9.jpg
13.jpg
11.jpg

My T was invited to a armature painting group

For sale: transmission clutch yoke collar $25 plus shipping

For sale: Transmission driven gear puller Ford script 5Z326 $200 plus postage

Listing this for a friend who”s family member has passed away. 1925 sedan runs and drives has a rebuilt generator rebuilt coils rebuilt carburetor new front spring. $8000.00 The car is in Hyde Park Ny the owners name is Linda her phone number is (nine one four) -490-8843

Wanted BB BBR Rajo inlet manifold to rebuild this car as it was in 1925

Ted King Rajo.jpg

A close up of a similar manifold front Mark Chaffin's photo

2025-08-10 Rajo Inlet Maniflod to suit BB BBR.png

Frame brackets that the body to frame brackets mount to.
$30 for all plus shipping.

IMG_3969.jpeg

For Sale 2 late 13-16 frames. $100 each. Located near Moorhead MN. Due to the fact both have running board brackets, I'd say they were never trailers. Steve 701 212 5009

Had a good time at the Helping Seniors trunk or treat benefit.

For sale: set of fender irons. $75 plus shipping
20251010_180222.jpg 20251010_180158.jpg

This is the last available pair of new silicon steel cast differential housings. These are fully machined centres pressed into original tubes and backing plates. Fits all years internals perfectly Available now $2750 USD
Eric Edwards 705 828 5405

I have a complete late rearend for a Model T. It has the wire wheel brake drums, complete rear axle, torque tube and drive shaft. The universal joint is not included. Make me a fair offer and pick up at my location. Tom Five03-644-937Four. I can take more pictures if necessary. SDC13029.JPG 's
The brake shoe's are also included.

New old stock taillight bracket for a Model A or Model B pick-up truck. $25.00 plus the cost of postage. Tom Five03-644-937Four SDC12991.JPG

A pair of backing plates for the 1926/27 model T. They are in fair shape and can be used with a little work. $20.00 for the pair plus the ride. Tom
five03-644-937Four SDC13026.JPG SDC13025.JPG

October 1924 Ford Service Bulletin Page 76, shows the new rib, or oil deflector cast into the transmission cover. I recently bought an earlier version transmission cover, by mistake, relying on another persons judgement.

lOOKING TO EQUIP A RIGHT HAND DRIVE NON STARTER CAR TO A RIGHT HAND DRIVE STARTER CAR USING JUST A STRIPPED (BARE) HOGSHEAD CASTING. DOES ANYONE KNOW IF THERE ARE PEDAL INTERFACE DIFFERENCES SUCH THAT THE PEDALS WOULD NOT FIT?

Please help! I am looking for a Ford Model NRS intake manifold. If you have an extra one I would like to buy it. The one on my N is a model T intake manifold that has been modified by cutting off the goose neck and welding it back on 180 degrees out (right hand drive versus left hand drive). I would really appreciate your help if you have an extra...

Looking for wheel for 1916 Touring. I have hub.
Campbell Tellman II
Beaufort, NC

For Sale 1 3/4 frames pictured. 1910-13. $600 for both. Located near Moorhead MN. Steve 701 212 5009

Oil Pan Model T Ford 1920s 26' 27' Metal 3 and 4 Dip.
I have about 5 or 6 oil pans for sale
Asking $50 a piece or $200 for all of them. Local pick up to 75002.

2025-04-13 10.32.472.jpg
2025-04-13 10.32.442.jpg
497635360_711929594825843_4086163399676039494_n.jpg

Free generator. You pay postage. Condition unknown.

Please pm me if interested.
PayPal fine.

Love to find someone with some 1926 zinc door grommets for a roadster. Anyone have any they would be willing to part with?

Last pair. Silicon steel castings machined as per original pressed into original tubes and backing plates. Workmanship guaranteed perfect $2750 USD Eric Edwards 705 828 5405

I am in need of the passenger side, side light bracket for a 1912 model T touring. The one in the picture is for the driver side, I need the one on the passenger side you can reach me through text message. My number is 419-217-8884. Thanks.

I am in need of the passenger side, side light bracket for a 1912 model T touring. The one in the picture is the driver side, it is the passenger side that I need. Thanks.

Nice pair of early E & J sidelights. A couple of the lenses are cracked. Both have burners in them. Would be nice on an original car or restore them. $400 for the pair plus shipping to the lower 48. Contact me through text message. My number is 419-217-8884.

20251019_094403.jpg

Ships flat. $40 shipped to lower 48

PayPal or check is fine.

Email via forum

Nice pair, $60.00 plus shipping. Kdmks AT att.net.

NOS 1915 door with lock and hinge. Original black paint. $250 plus shipping. Kdmks AT att.net.

fitting things together on my two current projects. IMG_4459.jpeg IMG_4460.jpeg IMG_4466.jpeg IMG_4464.jpeg IMG_4465.jpeg

I will buy your extra coils outright or arrange for you to get rebuilt coils back as payment or partial payment. I rebuild coils for private individuals and Model T parts suppliers and we are always looking for good usable coils for rebuilding.
I have worked this deal many times in the past and know what works and what doesn’t for both of us and...

20251017_105814.jpg

One rubber stem 30 x 3 1/2 tube for sale.

$20 + $17 shipping.

PayPal or check.

Email via forum.

20251017_102227.jpg

20251017_102216.jpg

For Sale, Startometer SB. Still works.

$45 shipped. PayPal or check is fine.

Email via forum.

Torpedo wedding day.png

From Tom Rootlieb .

Does anybody know who was selling these vintage gas pumps at Hershey this year?

I found the best aerosol clearcoat to protect polished brass that I have ever used in “Mohawk Gloss Lacquer for Brass” that can be purchased from Amazon. It goes on perfectly clear without fogging up or developing bubbles.

IMG_7285.jpeg IMG_7286.jpeg

1926 Model T Coupe. Over the top build. Powerful smooth engine with Model A carb and manifolds, electronic distributor, alternator, 12V, KC Warford, Shure-Stop disc brakes. Many other extras, including wind wings, 3rd stop light, turn signals, etc. Beautiful body, interior and paint. Made to run and tour. $18000. PM Kurt in Great Falls, MT....

New brake quadrant
$25 plus shipping

IMG_3917.jpeg IMG_3916.jpeg

Here’s a reproduction early style water outlet.
Has a crack around bolt boss. Easily repaired.
$50 plus shipping.

IMG_3913.jpeg IMG_3911.jpeg IMG_3912.jpeg

I have an assortment of frame brackets for my 12. These are the ones that are riveted with two rivets to the sides of the frame that the body to frame brackets would mount to. Some the steel is thicker than the others.
Anyone know if the earlier brackets were thinner or thicker than later ones?
IMG_3910.jpeg

Thanks!
Mike

Asking for a recommendation: does anyone know where I can get roller shades restored with period correct fabric material for a '17 Towncar?

Very Rare 1909 Buffalo Carburetor that has been restored by Russ Potter. They were used on Model Ts up until April of 1909. PENDING shipped with insurance to the lower 48.
Lang’s 1-800-872-7871 M-F 9-5:30 eastern time.

Looking for the steel bonnet Victor (1) headlight if you have an extra. Please PM ME, Best John

Hi all, I have recently begun restoring a '27 TT pickup. Both of the rear rims are badly rusted and need to be replaced. The tires which I pulled off of them were Wards Riverside 32x6, 7.00-20, which need to be replaced as well. If anyone out there has a good pair of rims and would like to sell them, please send me a private message.

I struck out at Hershey. Looking for a 17-23 left front fender.

1914 Holley G, new float, float valve, venturi and choke spring, throttle shaft bushing installed, reconditioned spray needle, test run. $300 postpaid to continental USA email: wlkma9@gmail.com

Good morning all and Happy High Holy Days of Hershey,
We are all set up and will be ready for business on this last morning. If anyone is looking for the best quality starters, coils, or voltage regulators, stop by and see us Hershey GBH17-18. With the help and cooperation of Jeff Stevenson of Modeltstarters.com, we’ve been able to bring you the...

Looking to buy a high hood cowl. None found at Hershey 😞.

Edit, found one online.

Hi all, we had a very cool tour this past Saturday through the North Chagrin Metroparks in Northeast Ohio. Our club, the Bumps'n'Grinds, is smaller in numbers, so we invited the Northern Ohio Model A Club and a few other VIPs (an Overland and a Willys-Knight). The weather was perfect, the roads were in great shape, the cars ran extremely well and...

I just found 5 brand new, in the package 1/4-32 taps. They are top quality Chinese made...not my normal USA taps that I typically offer, but are still a quality product and will work just fine for many many years. The bonus is, these are FREE and my USA ones are not...

In case you missed it, they are FREE if you buy 2 or more Full Flow Float...

Will there be an EFR meeting at Hershey this year?
If so when and where?

Thank you.

Does anybody know what these look like? I know what the rear one looks like and the middle one, but the front one (according to catalogs) is for 24-27....so, is the 1909 front bearing different than this later one?

Also need to know which way the bearing clip goes, at the moment I've got it drawn on the top side of the bearing, because this puts...

Saw a really nice 13 Turtle deck in the Chocolate Field South today. Not mine but if I needed one it would be.
Come by my spaces CR33-38 and I will show you here it is.
I don’t know the space number but I can show you. Dan

Pretty good documentary on the Ford Model T Ignition Coil:

For sale: driveshaft housing with driveshaft $75 plus postage

20250829_183809.jpg 20250829_183841.jpg

Hello T lovers! I am wondering if any one from the Colorado front range, or even Albuquerque to Cheyenne will be attending the Texas T party and can return with a set of fenders. One day I will have to make it to that round up but alas, not this year. If transporting front and rears is possible for anyone please give me a shout! I am pricing the...