Search found 366 matches

by Joe Bell
Sat Dec 14, 2019 11:20 am
Forum: General Discussion Forum (started 2019)
Topic: Does anyone have a paint code for Model A engine green?
Replies: 6
Views: 644

Re: Does anyone have a paint code for Model A engine green?

Vendors have two different colors of green one that is a medium green is Gaslight's the forest green Snyder's carry so depends on the color you want? They are both in rattle cans. Hope this helps.
by Joe Bell
Wed Dec 11, 2019 8:01 am
Forum: General Discussion Forum (started 2019)
Topic: Carmine Red
Replies: 11
Views: 1130

Re: Carmine Red

Steve, the one on my page is a 65, my wifes favorite.
by Joe Bell
Tue Dec 10, 2019 2:55 pm
Forum: General Discussion Forum (started 2019)
Topic: Carmine Red
Replies: 11
Views: 1130

Re: Carmine Red

A real close color to my Tudor is a 69 Ford color, it was on my Mach one years ago, not quite as brown cast but better color to me, take a look!
by Joe Bell
Tue Dec 10, 2019 2:52 pm
Forum: General Discussion Forum (started 2019)
Topic: Is this a "dummy" flywheel ring gear for a non-starter car?
Replies: 40
Views: 2659

Re: Is this a "dummy" flywheel ring gear for a non-starter car?

Just tore down a 19 with out a starter, ring gear was on the flywheel, I suspect some one had a flywheel with bad teeth and chucked it up and turned them off on a big lathe? Looks original screws as they said earlier.
by Joe Bell
Tue Dec 10, 2019 2:47 pm
Forum: Classifieds - Parts
Topic: WTB: Inside oil line with large funnel.
Replies: 3
Views: 390

Re: WTB: Inside oil line with large funnel.

Vendors have new ones that fit well, unless they are out of stock.
by Joe Bell
Mon Dec 09, 2019 10:08 pm
Forum: General Discussion Forum (started 2019)
Topic: How do you separate two transmission drums?
Replies: 6
Views: 934

Re: How do you separate two transmission drums?

As they said earlier check the gear, I will take a flat file on the outside of the gear to knock the burr's off when you look at the low speed drum some will have a groove cut into the gear if lots of use.
by Joe Bell
Sun Dec 08, 2019 9:23 am
Forum: General Discussion Forum (started 2019)
Topic: Valve Springs
Replies: 4
Views: 539

Re: Valve Springs

I had heard the ones from Gaslight are made in Springfield Ohio?
by Joe Bell
Sat Dec 07, 2019 10:49 am
Forum: Classifieds - Parts
Topic: Wanted: running board spare tire bracket
Replies: 3
Views: 461

Re: Wanted: running board spare tire bracket

Alex, I have half of one, some one cut the mounting part off.
by Joe Bell
Mon Dec 02, 2019 10:36 am
Forum: Classifieds - Parts
Topic: two man top
Replies: 0
Views: 279

two man top

I picked this up years ago for a 17 touring, I no longer have the car and time to part with this, it is to large to ship for what it is worth, the bows are there one socket has some rust through on it, if of interest give me an email and will have the wife take some pictures of it. Thanks Joe Bell T...
by Joe Bell
Sun Dec 01, 2019 4:06 pm
Forum: General Discussion Forum (started 2019)
Topic: This Day In History - December 1, 1913
Replies: 5
Views: 706

Re: This Day In History - December 1, 1913

The conveyor chain that hauled the T's down the assembly line was called CC5 was mfg at Webster Industries in Tiffin Ohio, I retired out of there a few years ago and when I started an ole boy told me the story and had a picture of the original line in a picture frame in his locker, that an old boss ...
by Joe Bell
Thu Nov 28, 2019 10:19 am
Forum: General Discussion Forum (started 2019)
Topic: looking for KR wilson triple gear reamer for drum machine
Replies: 1
Views: 395

Re: looking for KR wilson triple gear reamer for drum machine

Now I know some one has to have an extra one? 143 people have looked? any one? would love to complete my set. Thanks Joe
by Joe Bell
Tue Nov 26, 2019 10:14 pm
Forum: Classifieds - Parts
Topic: WTB Spark Plug BOX
Replies: 4
Views: 1066

Re: WTB

If I remember the 09 had splitdorfs or Moslers plugs in them? He has worked on this car for 40 plus years to make it as original as possible, I think he is wanting to make up a show case of 09 parts to go with it. He found some original tools thanks to Don Lang recently!
by Joe Bell
Tue Nov 26, 2019 3:23 pm
Forum: General Discussion Forum (started 2019)
Topic: looking for KR wilson triple gear reamer for drum machine
Replies: 1
Views: 395

looking for KR wilson triple gear reamer for drum machine

The topic says all, what do you have? Thanks Joe Bell 419-618-1025 Tiffin Ohio
by Joe Bell
Mon Nov 25, 2019 8:55 am
Forum: Classifieds - Parts
Topic: WTB Spark Plug BOX
Replies: 4
Views: 1066

Re: WTB

I think he is looking for an early spark plug box for what would of been in his 09 roadster, he had talked about it to me before hershey to look for one.
by Joe Bell
Mon Nov 18, 2019 8:04 am
Forum: General Discussion Forum (started 2019)
Topic: Engine was running, now seized
Replies: 25
Views: 2498

Re: Engine was running, now seized

Just because an engine has been sleeved does not mean it can not leak where a repair was done.
by Joe Bell
Mon Nov 18, 2019 8:01 am
Forum: General Discussion Forum (started 2019)
Topic: 26 Brake Cam Question
Replies: 23
Views: 1571

Re: 26 Brake Cam Question

My thought are some one took the time to make them, if you piss him off from his design there will be no more. That cam is for a Parking Brake not an emergency brake, But if you are using them for an Auxillary brake I would use a different cam. I did not make these and have nothing to do with who ev...
by Joe Bell
Mon Nov 18, 2019 7:48 am
Forum: General Discussion Forum (started 2019)
Topic: Oil Leak coming from weep hole in starter
Replies: 3
Views: 581

Re: Oil Leak coming from weep hole in starter

If the oil pours out of the top petcock you have to much oil in it and it will leak there more often than when it trickles out of the petcock. Just my thoughts.
by Joe Bell
Fri Nov 15, 2019 11:16 am
Forum: General Discussion Forum (started 2019)
Topic: Ring gear and pinion
Replies: 5
Views: 740

Re: Ring gear and pinion

If you are pulling hills all the time the ten tooth is great but if you are flat lands I would run the eleven tooth.
by Joe Bell
Mon Nov 11, 2019 5:08 pm
Forum: Classifieds - Parts
Topic: WTB wanted ‘24 ‘25 coupe quarter window hardware
Replies: 7
Views: 486

Re: WTB wanted ‘24 ‘25 coupe quarter window hardware

I should of said they can be used if trimmed down, done it a few times, they are easier to find.
by Joe Bell
Sun Nov 10, 2019 7:37 am
Forum: General Discussion Forum (started 2019)
Topic: Himico Cylinder Head
Replies: 15
Views: 2277

Re: Himico Cylinder Head

I have one of those heads on my fordor and have ran it for years, works great, I have an extra one that I may part with, no cracks! Thanks Joe
by Joe Bell
Sat Nov 09, 2019 1:25 pm
Forum: General Discussion Forum (started 2019)
Topic: Couple questions regarding oversize pistons/valves
Replies: 11
Views: 797

Re: Couple questions regarding oversize pistons/valves

I think you have the problem solved this way!
by Joe Bell
Fri Nov 08, 2019 7:04 pm
Forum: General Discussion Forum (started 2019)
Topic: Couple questions regarding oversize pistons/valves
Replies: 11
Views: 797

Re: Couple questions regarding oversize pistons/valves

Snyder's year ago fixed the relief in the pistons hitting head or head gasket from the relief in the pistons, I would look for marks that are shiny will tell you what is happening. I really hate going over .060 on bores! Just my thoughts!
by Joe Bell
Sat Nov 02, 2019 3:38 pm
Forum: Classifieds - Parts
Topic: WtB set of NON DEMOUNTABLE BANDS
Replies: 4
Views: 477

Re: WtB set of NON DEMOUNTABLE BANDS

I have been throwing them away I have so many of them, to bad your not closer to me!
by Joe Bell
Sat Nov 02, 2019 8:31 am
Forum: General Discussion Forum (started 2019)
Topic: Adjustable lifters with stainless steel valves...
Replies: 22
Views: 1555

Re: Adjustable lifters with stainless steel valves...

Bill,
All the lifters I have seen rotate on running in a T.
by Joe Bell
Tue Oct 29, 2019 1:34 pm
Forum: Classifieds - Parts
Topic: WTB - high compression head
Replies: 7
Views: 811

Re: WTB - high compression head

Mike, It is cast that is why I have been running it, looks stock also to fool some people!
by Joe Bell
Tue Oct 29, 2019 10:16 am
Forum: Classifieds - Parts
Topic: WTB
Replies: 3
Views: 573

Re: WTB

Not sure either on the brass it goes through, never cleaned it up, it is up in the hay mow with other junk.
by Joe Bell
Tue Oct 29, 2019 10:14 am
Forum: Classifieds - Parts
Topic: WTB - high compression head
Replies: 7
Views: 811

Re: WTB - high compression head

Mike, I have one that looks like a T head but no wells at the spark plugs, been running on my Fordor for years. Joe
by Joe Bell
Tue Oct 29, 2019 10:12 am
Forum: Classifieds - Parts
Topic: WTB: RHD hogshead and other parts
Replies: 1
Views: 236

Re: WTB: RHD hogshead and other parts

I have one but it is big thing to ship. I am in Tiffin Ohio, Joe Bell 419-618-1025
by Joe Bell
Mon Oct 28, 2019 6:56 am
Forum: Classifieds - Parts
Topic: WTB
Replies: 3
Views: 573

Re: WTB

are they steel or brass? I have the whole lid with steel handles
by Joe Bell
Sun Oct 27, 2019 8:23 am
Forum: General Discussion Forum (started 2019)
Topic: Adjusting #4 ConRod on 3 dip pan?
Replies: 22
Views: 1665

Re: Adjusting #4 ConRod on 3 dip pan?

I would pull the engine and check out the rest, also good time to clean out the extra stuff floating around.
by Joe Bell
Thu Oct 24, 2019 1:11 pm
Forum: General Discussion Forum (started 2019)
Topic: Hershey 2019 Photos
Replies: 78
Views: 12492

Re: Hershey 2019 Photos

No.11 is Tami Bell my bride of 32 years.
by Joe Bell
Sun Oct 20, 2019 1:11 pm
Forum: Classifieds - Parts
Topic: Accessory door handle extensions, set of 3
Replies: 10
Views: 1052

Re: Accessory door handle extensions, set of 3

I have seen people use these for throttle and spark extensions also
by Joe Bell
Sun Oct 20, 2019 11:02 am
Forum: Classifieds - Parts
Topic: FS Brass era cylinder head with priming cups
Replies: 2
Views: 474

Re: FS Brass era cylinder head with priming cups

I was always told that this head was a late 12 head?? From the script around center hole and large casting Chabletts and No Made In US on it, I have seen several through the years am I correct on year? Thanks
Joe
by Joe Bell
Sun Oct 20, 2019 10:55 am
Forum: General Discussion Forum (started 2019)
Topic: Free sets of Kevlar transmission bands
Replies: 4
Views: 916

Re: Free sets of Kevlar transmission bands

I bought bands 20 years ago from Frank and John Iaccino at hershey, they where the Kevlar Band in the can logo, I have never had issues of getting bands from them. A while back there was some issues from other supplier's of wrong material and thickness but have never had problems with these boy's! T...
by Joe Bell
Sat Oct 19, 2019 10:30 pm
Forum: Classifieds - Parts
Topic: WANTED, original Babbitt rear axle thrust washers.
Replies: 10
Views: 925

Re: WANTED, original Babbitt rear axle thrust washers.

I have some in my stash, if you are not to far up in Michigan you are welcome to come and get them free!
by Joe Bell
Wed Oct 16, 2019 4:29 pm
Forum: General Discussion Forum (started 2019)
Topic: Engine Rebuilder Recommendation
Replies: 12
Views: 1363

Re: Engine Rebuilder Recommendation

Mike Bender is in your neck of the woods.
by Joe Bell
Mon Oct 14, 2019 5:18 pm
Forum: Classifieds - Parts
Topic: WTB hand crank
Replies: 9
Views: 770

Re: WTB hand crank

Charlie, you can come and take your pick, there are several to choose from. Joe
by Joe Bell
Mon Oct 14, 2019 7:08 am
Forum: Classifieds - Parts
Topic: WTB New Mag Ring
Replies: 4
Views: 631

Re: WTB New Mag Ring

Bill Lucius of New Riegel Ohio is making the best out there right now 419 -595- 2310
by Joe Bell
Sun Oct 13, 2019 5:21 pm
Forum: General Discussion Forum (started 2019)
Topic: My Hershey haul
Replies: 3
Views: 957

Re: My Hershey haul

I see you found the really good Kevlars, it is hard to find the good ones, they are not all the same!
by Joe Bell
Sat Oct 12, 2019 2:12 pm
Forum: General Discussion Forum (started 2019)
Topic: T's friends at Hershey
Replies: 0
Views: 592

T's friends at Hershey

I had a great time at hershey this year met some new faces to go with the names I see here often and a great place to find the hidden treasures, I know my wife loves her new Christmas present I found for her at Don Lang's tent!! Thanks Don for hauling the extra stuff that was not T related,. Thanks ...
by Joe Bell
Mon Oct 07, 2019 7:12 am
Forum: Classifieds - Parts
Topic: 9-12 field coils
Replies: 0
Views: 343

9-12 field coils

I have a couple extra 9-12 original field coils that I will haul to Hershey, one looks mint and other has some paper coming off c4i 29-31 or light pole 41 and some other odds and ends for T's. Thanks Joe 419-618-1025
by Joe Bell
Sun Oct 06, 2019 6:42 pm
Forum: Classifieds - Parts
Topic: '21 engine FS
Replies: 4
Views: 842

Re: '21 engine FS

I remembered seeing that stand not to long again?
by Joe Bell
Sun Oct 06, 2019 12:16 pm
Forum: Classifieds - Parts
Topic: Looking for 1909 block casting
Replies: 15
Views: 1536

Re: Looking for 1909 block casting

Tim Morsher had some one casting in Bronze, he is out of Norwalk Ohio, he is on the forum.
by Joe Bell
Sun Oct 06, 2019 8:44 am
Forum: Classifieds - Parts
Topic: Looking for 1909 block casting
Replies: 15
Views: 1536

Re: Looking for 1909 block casting

Chad, There is two foundries local, One is Webster Mfg. that pours the malliable iron, This company made the chain for Henry to haul the cars down the assembly line it was called CC-5, they can handle any large amounts items to pour, I retired out of here as a Machinist, The other is Tiffin Foundry ...
by Joe Bell
Fri Oct 04, 2019 5:37 pm
Forum: General Discussion Forum (started 2019)
Topic: A nice send off
Replies: 10
Views: 1264

Re: A nice send off

Nothing better than that, I did the same years ago for a friend in his 11 roadster.
by Joe Bell
Fri Oct 04, 2019 5:34 pm
Forum: Classifieds - Parts
Topic: 2 3/4 to 1 PINION GEAR
Replies: 11
Views: 1040

Re: 2 3/4 to 1 PINION GEAR

All three are 39
by Joe Bell
Fri Oct 04, 2019 12:10 pm
Forum: General Discussion Forum (started 2019)
Topic: Introduction and question
Replies: 12
Views: 1401

Re: Introduction and question

Fold the windshield less chances of an on coming stone.
by Joe Bell
Fri Oct 04, 2019 12:07 pm
Forum: Classifieds - Parts
Topic: Looking for 1909 block casting
Replies: 15
Views: 1536

Re: Looking for 1909 block casting

Cast iron does shrink also, I made a few High Compression heads from Malleble, did not work from annealling them and cracking, to making them out of grey iron that worked for me and machining later.
by Joe Bell
Fri Oct 04, 2019 8:52 am
Forum: General Discussion Forum (started 2019)
Topic: Scandinavia bands improvement?
Replies: 4
Views: 670

Re: Scandinavia bands improvement?

I have a transmission to repair with a blued low speed drum that got hot and cracked from the kevlar, I do like my old cotton bands!
by Joe Bell
Fri Oct 04, 2019 7:02 am
Forum: Classifieds - Parts
Topic: 2 3/4 to 1 PINION GEAR
Replies: 11
Views: 1040

Re: 2 3/4 to 1 PINION GEAR

I have three ruckstel rings and have never counted them, knew by the offset gear, I will check now!
by Joe Bell
Thu Oct 03, 2019 4:01 pm
Forum: General Discussion Forum (started 2019)
Topic: Kevlar-ing along when the nut dropped into nether regions.
Replies: 27
Views: 2750

Re: Kevlar-ing along when the nut dropped into nether regions.

An older friend had this happen, he took a couple tube socks put them in the starter hole and rolled the engine over slowly, they came up and around and he got them out, make sure you count the socks, it will make a really big mess if one is left in there. Hope this helps, thanks Ray Miras from Mich...
by Joe Bell
Thu Oct 03, 2019 1:19 pm
Forum: Classifieds - Parts
Topic: Looking for 1909 block casting
Replies: 15
Views: 1536

Re: Looking for 1909 block casting

Mike, the couple I took care of was fine on the head area, they where actually wider than the head.
by Joe Bell
Thu Oct 03, 2019 9:56 am
Forum: Classifieds - Parts
Topic: Looking for 1909 block casting
Replies: 15
Views: 1536

Re: Looking for 1909 block casting

I tracked the patterns from New York to Oregon then to Canada, the ole boy from Canada was real quiet about them, I have seen several of those blocks, they are beefed up inside like the later block are. I have a local foundry that would pour them but that does not do any good with out the patterns, ...
by Joe Bell
Tue Oct 01, 2019 6:20 pm
Forum: Classifieds - Parts
Topic: Looking for 1909 block casting
Replies: 15
Views: 1536

Re: Looking for 1909 block casting

Those patterns are still out there.
by Joe Bell
Mon Sep 30, 2019 8:13 pm
Forum: General Discussion Forum (started 2019)
Topic: How much time to pull an engine?
Replies: 19
Views: 1657

Re: How much time to pull an engine?

The old Ford book with time studies say you can pull it in 45 minutes, installation is 1 1/4 hours, best I have done is two hours, I guess I lost money on the Ford Jobber!
by Joe Bell
Sun Sep 29, 2019 10:42 pm
Forum: General Discussion Forum (started 2019)
Topic: Mag coil ring
Replies: 5
Views: 668

Re: Mag coil ring

Fordson tractor.
by Joe Bell
Sun Sep 29, 2019 5:48 pm
Forum: Classifieds - Parts
Topic: WTB steel rims
Replies: 5
Views: 375

Re: WTB steel rims

Al, I know there is a couple up in the barn, come take a look. Joe
by Joe Bell
Fri Sep 27, 2019 7:42 pm
Forum: Classifieds - Parts
Topic: wanted right hand parts
Replies: 8
Views: 582

Re: wanted right hand parts

Mike Lepsac has some parts he is hauling to hershey.
by Joe Bell
Fri Sep 27, 2019 7:41 pm
Forum: Classifieds - Parts
Topic: wanted right hand parts
Replies: 8
Views: 582

Re: wanted right hand parts

I never thought of the brake lever, I think you could reverse it all to make it work, except for the cam it would need turned and welded back on.
by Joe Bell
Wed Sep 25, 2019 4:45 pm
Forum: General Discussion Forum (started 2019)
Topic: Old Photo, Grandpa's coupe
Replies: 5
Views: 892

Re: Old Photo, Grandpa's coupe

Dave,
I know but it is a good standing joke for new bee's.
by Joe Bell
Tue Sep 24, 2019 4:10 pm
Forum: General Discussion Forum (started 2019)
Topic: Old Photo, Grandpa's coupe
Replies: 5
Views: 892

Re: Old Photo, Grandpa's coupe

That is proof, there is a Doctor bag there, so it must be a Dr. Coupe?
by Joe Bell
Sun Sep 22, 2019 9:37 pm
Forum: Classifieds - Parts
Topic: Smith Air compressor
Replies: 2
Views: 458

Re: Smith Air compressor

It has found a new home in Beaver creek.
by Joe Bell
Sun Sep 22, 2019 6:22 pm
Forum: Classifieds - Parts
Topic: Smith Air compressor
Replies: 2
Views: 458

Smith Air compressor

I recently picked up a couple of Model A engines and one has the smith air head on it and govenor, cooling tower also,I have no use for it would hate to scrap it out, figured maybe some one out there may collect them? 50.00 and it is all yours, will not ship! to heavy. Thanks Joe Bell 419-618-1025 T...
by Joe Bell
Sun Sep 22, 2019 5:20 pm
Forum: Classifieds - Parts
Topic: KR Wilson line boring equipment
Replies: 8
Views: 946

Re: KR Wilson line boring equipment

Model T stuff has found a new home pending payment. Thanks
by Joe Bell
Sun Sep 22, 2019 4:28 pm
Forum: Classifieds - Parts
Topic: CRAGAR OVERHEAD VALVE HEAD
Replies: 13
Views: 2543

Re: CRAGAR OVERHEAD VALVE HEAD

That will make it turn the tires! Looks good Bill!
by Joe Bell
Sun Sep 22, 2019 1:55 pm
Forum: Classifieds - Parts
Topic: KR Wilson line boring equipment
Replies: 8
Views: 946

Re: KR Wilson line boring equipment

Here are the pictures of the Model A line boring parts.
by Joe Bell
Sat Sep 21, 2019 7:17 am
Forum: General Discussion Forum (started 2019)
Topic: Sealing my 12 rivet rear end
Replies: 17
Views: 1619

Re: Sealing my 12 rivet rear end

John, just got done going through my 150 Franklin so I have been there also!
by Joe Bell
Fri Sep 20, 2019 9:30 pm
Forum: General Discussion Forum (started 2019)
Topic: Sealing my 12 rivet rear end
Replies: 17
Views: 1619

Re: Sealing my 12 rivet rear end

There is an RTV that is special for rear axle lubes, comes in a grey tube and says for rear axles, some lubes will eat away at the RTV"s. If you are going to all this work try to use the best. Just my thoughts!
by Joe Bell
Fri Sep 20, 2019 1:38 pm
Forum: Classifieds - Parts
Topic: KR Wilson line boring equipment
Replies: 8
Views: 946

Re: KR Wilson line boring equipment

Or if you have a smart phone she can send them.
by Joe Bell
Fri Sep 20, 2019 1:37 pm
Forum: Classifieds - Parts
Topic: KR Wilson line boring equipment
Replies: 8
Views: 946

Re: KR Wilson line boring equipment

Bill,
My wife was trying to figure out how to load them here and could not so???
by Joe Bell
Fri Sep 20, 2019 1:19 pm
Forum: Classifieds - Parts
Topic: KR Wilson line boring equipment
Replies: 8
Views: 946

Re: KR Wilson line boring equipment

I posted the pictures on the Model T site on facebook.
by Joe Bell
Wed Sep 18, 2019 3:57 pm
Forum: Classifieds - Parts
Topic: KR Wilson line boring equipment
Replies: 8
Views: 946

KR Wilson line boring equipment

I have KR Wilson Line boring plate for Model T and A with false cams pouring fixtures for blocks, boring bars with extra cutters, standard reamers 3,2 for the A's other pouring fixtures for rods and main caps for T,A both. Price is 500 a set and could deliver to Hershey if of interest. Thanks! Joe B...
by Joe Bell
Wed Sep 18, 2019 3:57 pm
Forum: Classifieds - Parts
Topic: KR Wilson line boring equipment
Replies: 0
Views: 234

KR Wilson line boring equipment

I have KR Wilson Line boring plate for Model T and A with false cams pouring fixtures for blocks, boring bars with extra cutters, standard reamers 3,2 for the A's other pouring fixtures for rods and main caps for T,A both. Price is 500 a set and could deliver to Hershey if of interest. Thanks! Joe B...
by Joe Bell
Wed Sep 18, 2019 10:33 am
Forum: Classifieds - Parts
Topic: OT - Wanted - V8 60 h.p. manifolds
Replies: 10
Views: 826

Re: OT - Wanted - V8 60 h.p. manifolds

Carlton's number 419-294-8395
by Joe Bell
Tue Sep 17, 2019 9:45 pm
Forum: Classifieds - Parts
Topic: OT - Wanted - V8 60 h.p. manifolds
Replies: 10
Views: 826

Re: OT - Wanted - V8 60 h.p. manifolds

THere is an ole boy in Upper Sandusky Ohio that runs Carlton's machine shop, I know he has a bunch of them was just in his back room a couple days ago was wonder what all the snow mobile pistons where for and he told me they where the 60's pistons?? first I saw of them out of an engine.
by Joe Bell
Sun Sep 15, 2019 7:38 am
Forum: Classifieds - Parts
Topic: FREE very early TT rear axle NORTHERN OHIO
Replies: 4
Views: 543

Re: FREE very early TT rear axle NORTHERN OHIO

I can't believe you got rid of some good yard art???
by Joe Bell
Sat Sep 14, 2019 5:15 pm
Forum: General Discussion Forum (started 2019)
Topic: 1919 Engine with no provision or casting to accept a generator?
Replies: 18
Views: 1532

Re: 1919 Engine with no provision or casting to accept a generator?

I have a 4th month casting of 19 with no generator hole and it is an original block and numbers. They are out there!
by Joe Bell
Sat Sep 14, 2019 5:12 pm
Forum: Classifieds - Parts
Topic: Early two piece timer
Replies: 3
Views: 715

Re: Early two piece timer

I have a new fiber ring that is of no use to me so if some one buys this would be glad to find a new home for it. I think there is two rollers around also.
by Joe Bell
Fri Sep 13, 2019 12:28 pm
Forum: Classifieds - Parts
Topic: 18 complete engine for sale
Replies: 3
Views: 757

Re: 18 complete engine for sale

I think it has found a new home, thanks for the interest,Joe
by Joe Bell
Thu Sep 12, 2019 6:21 pm
Forum: Classifieds - Parts
Topic: 18 complete engine for sale
Replies: 3
Views: 757

18 complete engine for sale

I have a early 18 engine that was rebuilt years ago, .040 over on pistons, new babbitt, crank has been ground, new one piece valves, you can hear it run, was converted to a starter engine. It was a spare engine for an older friend had it in his car for touring while the original engine got rebuilt, ...
by Joe Bell
Sun Sep 08, 2019 6:34 pm
Forum: Classifieds - Parts
Topic: Splitdorf water pump-mag drive w/ magneto.SOLD,SOLD
Replies: 13
Views: 1686

Re: Splitdorf water pump-mag drive w/ magneto

It has the better mag on it with the built in impulse.
by Joe Bell
Sun Sep 08, 2019 8:38 am
Forum: General Discussion Forum (started 2019)
Topic: Need name and ph number
Replies: 3
Views: 565

Re: Need name and ph number

Ron,
Is it something you want me to pick up at hershey to take care of? Joe Bell 419-618-1025
by Joe Bell
Fri Sep 06, 2019 6:58 am
Forum: General Discussion Forum (started 2019)
Topic: Triple Gear Pins
Replies: 26
Views: 2280

Re: Triple Gear Pins

Gaslight in Urbana Ohio had some oversized ones, they where over on the part that pressed in and where the triple gear ran, would need to ask special for them. Hope this helps
by Joe Bell
Thu Sep 05, 2019 7:49 am
Forum: General Discussion Forum (started 2019)
Topic: Oil dippers on rod cap question
Replies: 4
Views: 870

Re: Oil dippers on rod cap question

I have pulled down engines with odd pistons in them, you have to remember at one time nothing was availible, I have seen plenty of Ford 292 or 312 piston in them that may be what you have. Hope this helps.
by Joe Bell
Tue Sep 03, 2019 1:20 pm
Forum: Classifieds - Parts
Topic: rebuilt 24&26 engine
Replies: 3
Views: 659

Re: rebuilt 24&26 engine

The second one is spoken for , Thanks Joe
by Joe Bell
Tue Sep 03, 2019 10:39 am
Forum: Classifieds - Parts
Topic: rebuilt 24&26 engine
Replies: 3
Views: 659

Re: rebuilt 24&26 engine

The 26 Canadian is spoken for, thanks Dallas.
by Joe Bell
Tue Sep 03, 2019 10:12 am
Forum: Classifieds - Parts
Topic: rebuilt 24&26 engine
Replies: 3
Views: 659

Re: rebuilt 24&26 engine

Sorry for the double post, Could haul to hershey if paid for before.
by Joe Bell
Tue Sep 03, 2019 9:19 am
Forum: Classifieds - Parts
Topic: rebuilt 24&26 engine
Replies: 3
Views: 659

rebuilt 24&26 engine

Selling for a friend that has passed away a Canadian built .060 over on the bore .020 over on the rods and mains 280 chaffin cam still in the crate from shipping, 26-7 engine. The other is a stock rebuild 23-25 engine that is .030 over on bore and .020 over on rods and mains both have adjustable lif...
by Joe Bell
Tue Sep 03, 2019 9:19 am
Forum: Classifieds - Parts
Topic: rebuilt 24&26 engine
Replies: 0
Views: 275

rebuilt 24&26 engine

Selling for a friend that has passed away a Canadian built .060 over on the bore .020 over on the rods and mains 280 chaffin cam still in the crate from shipping, 26-7 engine. The other is a stock rebuild 23-25 engine that is .030 over on bore and .020 over on rods and mains both have adjustable lif...
by Joe Bell
Sun Aug 25, 2019 7:59 pm
Forum: Classifieds - Parts
Topic: Wanted 1914 Cylinder Block
Replies: 3
Views: 636

Re: Wanted 1914 Cylinder Block

I have a 3-22-14 block that is machine and ready to build, picked up at hershey last year.
by Joe Bell
Tue Aug 20, 2019 8:05 pm
Forum: General Discussion Forum (started 2019)
Topic: Twin High Transmission accessory
Replies: 22
Views: 1731

Re: Twin High Transmission accessory

Just saw one the other day, Constantine has one, neat looking piece and light weight.
by Joe Bell
Sat Aug 17, 2019 7:10 am
Forum: General Discussion Forum (started 2019)
Topic: What should this sell for?
Replies: 13
Views: 1633

Re: What should this sell for?

John,
It is a together car not basket case, I would think 4000 to 4500 depending on the title, some one could buy it the way it is and have all kinds of fun.
by Joe Bell
Tue Aug 13, 2019 7:38 pm
Forum: Classifieds - Parts
Topic: Nice original pair of engine pans for sale
Replies: 1
Views: 481

Re: Nice original pair of engine pans for sale

Winter is coming! a good way to keep warm on a cold day!
by Joe Bell
Tue Aug 13, 2019 6:18 pm
Forum: Classifieds - Parts
Topic: looking rebuilt engine
Replies: 4
Views: 819

Re: looking rebuilt engine

The block is a 5-22-13.
by Joe Bell
Tue Aug 13, 2019 12:58 pm
Forum: General Discussion Forum (started 2019)
Topic: 1924 ? Motor
Replies: 15
Views: 1384

Re: 1924 ? Motor

25 pan, squared off pan mount ears at the bottom.
by Joe Bell
Tue Aug 13, 2019 12:55 pm
Forum: Classifieds - Parts
Topic: looking rebuilt engine
Replies: 4
Views: 819

Re: looking rebuilt engine

Andrew, I have mid year 13 block that is bored a seats in it can build shortblock or completed engine with correct parts, I do not have a 13 head, have 11-12 and 14 up. I do hershey every year and deliver to hershey for over seas buyers. Thanks Joe Bell 419-618-1025
by Joe Bell
Wed Jul 17, 2019 10:46 am
Forum: Classifieds - Parts
Topic: OT aircraft
Replies: 3
Views: 624

Re: OT aircraft

I know they converted a few of these to tailwheel.