MTFCA Forum

Larry

Mike
I’m pretty sure I have some. Let me know if you have not already found one and I will check.

Larry

Andy,
I will private message you my phone number.
Larry

Larry

This is an early 15 with the riveted flat strap bracket. It measures right at 25” end to end.

I could not PM the photo , so I posted it here.

Larry

I probably have one .
If you haven’t found one yet pm me and I will look.

Larry

If your still looking for these,
I have one or two sets of the reproduction wide track axles
available and could probably help you out with those.

Larry

How much do you need?
If you can’t find any,
I probably have a roll.

Larry

I have a couple extra cans if you haven’t found any.
The cans are probably about 3/4 full and have been stored in a paint cabinet. They are sill liquid and should be fine. If you need them, message me your address and I can send them out in the morning.

Larry

David, If it’s a 23 to 25 Tudor, the stripe was just below the belt molding and went all the way around the body crossing over all the half oval trim. The stripe was 1/16th of an inch give or take depending on who applied it. Because the stripe was applied by hand, it could vary slightly in size & d...

Larry

Hello Terry, Stopped at the shop on my way to church and checked in the book. That cable and housing fit a 29 to 31 Chevrolet.

Larry

Hello Terry,
You have a Cable that fits a 30/31 Chevrolet.
If you measure the length I could tell you if it fits other years. I believe the 1930/31 Chevrolet speedometer was an AC as Mark said.
Larry

Larry

Here is a close up of a 1910 firewall that I did with Laurel Mountain Forge Cherry on the correct cherry Veneered firewall.
It’s a beautiful stain and I agree with you Tim probably very close to the original color.

Larry

Hello Larry,
I have a couple pieces of the 7/16 left from my 1913.
If you think one of these is long enough or you could use the pair of them. Let me know and my wife will get them out in the mail to You.

Larry

Larry

Hello Jack, If you’re looking for a high-quality finish I would definitely seal the wood first. For years when I was a commercial painter, I used various sanding sealer’s on newly spoke wood wheels with great success. Then the paint companies were forced to modify those products by the EPA. After th...

Larry

Very glad the two of you are ok and no was hurt. My wife and I had a similar experience 25 years ago. We were leaving the 4th of July fireworks at the Monroeville Mall in Monroeville Pa. with our four children in the back seat of a 23 touring we owned at the time. We headed out of the mall complex a...

Larry

Very Sorry to here this.
Charlie was a friendly, helpful guy and I Always enjoyed talking with him. He Sent me a couple parts that I needed to complete a 1916 Overland restoration Several years ago when he heard I needed them. Appreciated his knowledge and kindness.
Praying for his family.

Larry

Got them Steven.
Will check over the weekend.

Larry

Not a problem Steven,
Will wait for your photo.

Larry

Hello Steven,
Do you have a picture of the one you are looking for?
If so I will go through the ones I have and see if I have a good one.
Larry

Larry

Hello John, Emailed you My address and contact information. Let me know if you need anything else.
Thank You,
Larry

Larry

Larry

Hello John,
I have an NOS right rear fender for a 24-25 four door sedan. Can email you a picture Of it tomorrow if interested. $150.

Larry

Thank You Joe for going out of your way this past week and the time you took to help me out. The parts arrived this morning and are a perfect fit.
Really appreciate all you do!
Thanks again!
Larry

Larry

That would be great Joe!
Attached is a picture that shows the contour of the edge.

Larry

Hello Joe, I hope you and your family are all doing well. Will try to get out your way in the near future and take a look. If you happen to get in this way let me know as I have accumulated quite a few engines, mechanical parts, and rear ends that are yours if you can use them. The doors on this car...

Larry

Looking for two garnish moldings for the 23 to 25 coupe/sedan doors. These would be the upright moldings on the door handle side of the doors. Not sure exactly what the length of those are as the ones that were on the car had been cut. My guess is they are around 19 3/4” long.

Thank You,
Larry Gresh

Larry

Mike, Those brackets were used with the rands windshield in 1911 as well. The 1909,1910 Rands with the internal spring hinges had equal windshield halves (13 3/4”). The 1911 Rands with the internal spring hinges Had the larger lower frame (14 3/4”) and the smaller frame on the top (12 3/4”). The att...

Larry

They are windshield to firewall riser brackets 1909, 1910. They fit around the ends of the firewall riser and clap on to the bottom of the windshield frame. They were steel that was brass plated.

Larry

I use to have an electric golf cart with six 6 volt batteries in it.
They were already connected in series and it worked great for this. I just disconnected the the leads and connected my cables.

Larry

Larry,
I will let you know if I run across any more.
How long are the pieces you need that run from the radiator to the lights.
Depending on how this goes, I may have a couple 12” pieces left when I’m done.
Larry

Larry

Had not thought about them Frank, but called them this morning and they had one piece left. It was the length I needed to the inch so I really appreciate the suggestion.

Thank You and Hank as well for the help!
Larry

Larry

Thank You Frank and Hank,
Not looking for the rubber hose and have done a google search but not found any like the original.
The suppliers use to carry it but have been out of it for about 8 months. It is on a long term back order.

Larry

Layden,

Attached is a photo of the hose along with a clamp.
Larry

Larry

Thank you Layden,
I appreciate you taking the time to look but I’m really looking for the original cloth covered hose for this car.
Larry

Larry

WTB, a good piece of red carbide hose to run from a carbide generator to the brass line.
Thank You,
Larry

Larry

The side light brackets were pressed steel and brass plated as were the fire wall riser to windshield brackets. Tail light bracket was cast steel and brass plated as well.

Larry

[/attachment]

Martin
Attached are a couple of photos of an original unrestored 1910 sediment bulb assembly. I think these photos came from Bruce Macaulay.

Larry

Larry

Happy Thanksgiving Martin,
Hope You are doing well.
Attached is a photo of an original one I restored for a customer’s 1910 I’m restoring.

Larry

Our four kids with their two cousins about 30 years ago.
One of my favorite photos.

Larry

Hello Tim,
I will take the six body brackets and the windshield hinges if they are not spoken for. If You could message me a total, I will get You a check out in the mail.
Thank You,
Larry Gresh

Larry

Larry

Looking for a pair of Rands windshield Brass support rods.

Thank You,
Larry

Larry

Larry

Larry

Larry

Larry

Hello Bill, What are you using for heat? I am restoring an early 10 as well. In fact I think it was built on the same day as yours. The emergency brake lever still had remnants of the original brass plating under the handle. I separated the handle from the shaft for plating as well. Separating the l...

Larry

Larry

I have a couple questions regarding an 09 Kingston coil box I am restoring for a project and thought I would ask them here instead of starting a new thread. 1.) The coil terminal thumb nuts are unique to the 09 Kingston box. Some of the suppliers sell a reproduction of that nut but I can find no ref...

Larry

Sold,
Thank You,
Larry

Larry

This is a professionally rebuilt 1922 engine with transmission. It came with a speedster project that I purchased several years ago and I kept the engine with plans of using it in one of my own cars. The woman I bought it from said that her husband had the engine professionally rebuilt and she thoug...

Larry

Just realized that we posted this in the wrong spot. Working on changing it now.
Thank You,
Larry

Larry

This is a professionally rebuilt 1922 engine with transmission. It came with a speedster project that I purchased several years ago and I kept the engine with plans of using it in one of my own cars. The woman I bought it from said that her husband had the engine professionally rebuilt and she thoug...

Larry

Sold to Randy,
Thank You!
Larry

Larry

Hello Randy,
Sent you a PM.
Larry

Larry

Hello Jim,
Responded to your PM.
Larry

Larry

Hello Willie,
My wife just checked the shipping to You in Everett Washington and through UPS from Ohio it is 93.04 for the four tires.
Thought I would post a response here as I have not had much luck sending emails or a PM through the forum.
Larry

Larry

For Sale: Nice set of tires. One of the front tires is a new Universal and does not appear to have had any use. The others are Lincoln's with a similar tread pattern. The rear tires have about 90% of their tread life left and the other front one has about 60%. $200 for all 4 tires plus shipping. tir...

Larry

Mario, From what I can see in your pictures, it appears to me that your tires are Universal tires. I do have a New original stock Universal 30x3 1/2 that has been properly stored for years. Still soft, pliable, with no age cracks. It is a very nice tire. Attached are some photos. If You have an inte...

Larry

Hello Mario,
What brand WW tires do you have? I have several new original stock white walls (Different brands). Don't want to break up any pairs or sets but I may be able to part with a spare if you need one.

Larry

Hello John,
Just sent You an email.
Larry

Larry

For Sale Nice antique tachometer. Works perfectly, looks to have had little use.
$75+shipping

Larry

Jim,
Thank You,
Larry

Larry

Would anyone have a phone number for Kim Dobbins?
Thank You,
Larry

Larry

PM sent
Thank You,
Larry

Larry

Sold to Art,
Thank You,
Larry

Larry

Had several sets of coils rebuilt by Brent Mize "The Coil Doctor". These 3 were in excess to my needs so I will offer them for sale here. Brent did a wonderful job on these coils and I would highly recommend him if you need any rebuilt. $75 each on these plus shipping. DSCN0740.JPG DSCN0738.JPG DSCN...

Larry

Hello Art, Is this the carburetor you are looking for? It is a Holley, all brass 3 screw with the patent pending on the top. It came with a 1913 I purchased years ago but I went with the Holley 2 screw on mine, thinking this was more 1914 era. It is a rebuilt carburetor that has been sitting here on...

Larry

Hello Eric,
Have not received a PM from You.
Feel free to Email me directly at:
LnLgresh@aol.com

Regards
Larry Gresh

Larry

I have a nice white T front floor mat for sale. Purchased it years ago and it's been in storage ever since. Will probably need a good cleaning. Can send a photo or two if interested.
$30 +shipping
Larry

Larry

Thank You Gary,
Emailed You directly.
Larry

Larry

Still available,
Larry

Larry

Sold
Thank You,
Larry

Larry

Adam,
You may very well be right.
I never thought about that .
With the rear wheel removed from the axle, the intact axle would fit inside this.
One thing I forgot to mention is that this is made to take a front wheel with it's bearings which will turn freely on it.

Larry

Hello Gary, I have a very nice one. For sale.
Will send You a PM, along with a photo.
Larry

Larry

Sold to Richard,
Thank You,
Larry

Larry

Sold to Richard,
Thank You,
Larry

Larry

Very nice clock made by the "New Haven Clock Co" in New Haven Conn. Case is all brass and would be beautiful polished. Face looks like porcelain. Very nice hands and bezel. (no key) $150 plus shipping.

Larry

This is a restored Ford script Anderson style timer that was restored by Mr. T's Timer Service over 20 years ago. Has been wrapped and setting on the shelf ever sense. Comes with a very nice Anco accessory timer with brass knurled nuts. All for $100 plus shipping.

Larry

Very nice early accessory cast license plate bracket. Doesn't appear to have ever been used. I think this style bolts to the headlight fork somehow, but not sure. $25 plus shipping.

Larry

Exceptionally nice pair of "Ford"/Victor Lamp Co Model 2 chimneys. I don't think anyone is reproducing this chimney and if you need a pair I don't think you'll find a nicer pair. These ones are in really great shape. Will include the rest of the lamp parts pictured. $100 plus shipping. DSCN0710.JPG ...

Larry

Very unusual item for the Model T. My guess is this was used on cars with a broken axle so they could be moved. But it is the only one I have ever seen like this. Makes a handy tool to use for pin striping wheels or for a wheel display. Just clamps on to any small drum backing plate. $200 plus shipp...

Larry

Sold to Keith,
Thank You,
Larry

Larry

Larry

Larry

Larry

Larry

Larry

Larry

Larry

Larry

Sold,
Thank You,
Larry

Larry

Sold,
Thank You,
Larry

Larry

Sold,
Thank You,
Larry

Larry

Sold to Tim,
Thank You,
Larry

Larry

Sold to Brad,
Thank You,
Larry

Larry

Sold to James,
Thank You,
Larry

Larry

Hello Jim,
Received Your PM,
And responded by PM since I do not have your email.
Larry

Larry

Thank You Dave for the info.
Larry

Larry

Hello Brad,
Sent You an email.
Larry

Search found 228 matches