MTFCA Forum

Saw this in a video on youtube, looks like a few levers or keyboard thing? Video never mentioned it.

so... whatzit?

175196176_10119384949772084_7911396783133350720_n.jpg 173893175_10119384949577474_1467281962443365801_n.jpg 174124835_10119384949846934_7723486759008432243_n.jpg

Does anyone know when Ford went from the one piece dust ring held on with a screw in front of the terminal stud to the split type held with a bolt and nut? McCalley's book shows a generator on page 277 with the early setup. The stud is not attached to the buss bar like the later ones. Pictures don't want to post today!

Any thoughts on whether a 2021 Ohio Jamboree of T's will take place???

Are the NH carbs all the same from 20 - 26 ? I’m looking for one for my 26 coupe and I thought the later ones (26-27) were slightly different......em I thinking correctly?
Anyone have a decent core they would sell?
Thanks in advance

So was out driving my 23 tourer , was down at sea level and to get home I had a long uphill climb , car started off well got a good race at the hill but getting near the top the car was struggling , into low gear then higher reves to get over the top . Should I be screwing out the meddle in the carb to help me up the hill an then screw in a bit on...

Question....
I purchased a Model T that was built in October of 1913 and it is titled as a 1913 car, but that is the same month they started the 1914 body style.
.
If it was your car and someone came up to you in the parking lot and asked what year your car was, would you go by year of manufacture or body style? If you read Michigan law related to...

Were these plugs used for military? or some other application ?
the 2nd is a timer part >>>>
thanks for the help, Bob

Come sell or buy at a great event !

You must be a dues paying member of
The Early Ford V-8 Foundation Museum
to vend at the swap meet.

FJ

61BB69C0-A62F-4590-AA9D-4DDF8FFDD178.jpeg

81ECAEB2-83B4-4422-89AC-39BE5918FBB8.jpeg

Good afternoon all.

I just bought a pair of Canadian Ts eh? One is a late 27 car with engine No. C-749243. This would put it after July. Possible this is a replacement engine? or extremely late 27? I have not seen the frame number yet, when the car arrives i will go looking for it (I dont know much about Canadian Model Ts i assume they also have...

Well, I wonder what the pacifist side of Henry would think of this?

1.jpg

2.jpg

3.jpg

00 Tue Safety with Subtlety 1 the purchase.jpg

This will be a 10-part series with an an additional chapter each day, keeping within this thread. It's mostly about safety modifications made to my Model T. I hope you'll find it worthwhile or maybe just entertaining.

There are two primary levels of participation in the antique car hobby On one...

OK so my engine is in and the motor mounts are bolted as well as the front. My Radius Rod needs to go back about an inch. Someone recommended jacking up the rod and it should pop in. I tried and that didn't work. These are the same parts going back together. Is there a way to shift the front end back as well? I don't like to force things. Any...

Anyone have a Seng Steering Wheel that could let me know how to get the horn ring working? I'm pretty sure I have a missing part that is right below the wheel that contacts the horn ring.. There has to be a sliding part that contacts the ring on the wheel.

It's a pretty neat after market wheel. The anti-theft part works great. On and off with...

I wired my 26TT according to Ron Patterson's diagram. It is 6v negative ground with a voltage regulator. It is not running yet but when I turn on the lights the ammeter pegs to the right (charge). What do I do?

So I have heard about a car, called a stuts bearcat, that is this?

I planned to have the frame/axles/wheels blast cleaned and then brush paint them using Rust-Oleum primer and Rust-Oleum black gloss. However, I now am considering having them powder coated. I would appreciate members commenting on these two options.

I had my transmission out about 15 years ago at which time I replaced all of the bushings, new bands and maybe clutch disks (can't remember). Anyway I took the cover off today to adjust bands and decided to just check things over. This is an improved T with the driving plate that fits inside the drum. The first thing I noticed was that the screws...

87C89E50-A5D2-41A1-82E7-730DAA9B8716.jpeg DB3C160F-064D-4ADC-ACF2-770B324B5831.jpeg C5185354-9A0B-41BA-BC72-30063B0DE4F2.jpeg 3F260728-9932-4572-8667-2A610E2339BD.jpeg

What’s the best way to trailer a Tudor Sedan on a open trailer? Frontward or backwards?

Did some horse trading with my dad. What's the wrench for? PXL_20210419_204315599.jpg PXL_20210419_204324515.jpg PXL_20210419_203337840.jpg PXL_20210419_203320977.jpg

Has any Forum member purchased this mirror?
If so, I'd like to know how well it works.
Is there something better out there for a 1913 Ford Touring?

Thank you,
Gene

Hello everyone, it’s been many years since I’ve been here....

My ‘24 touring car has been collecting dust for awhile, and I’m thinking about getting her back on the road for the summer. I’d like to get a new top for her, it’s looking kind of ratty.

Two questions:

Which kit is recommended, and is there anyone in the downstate NY area (Hudson...

For anyone who has stopped at Pioneer Village in Minden, Nebraska, you may have seen this custom bodied Model K:

55C9FC62-6C3A-4D17-8654-150A4F10EEAE.jpeg

91CD3606-2183-474D-846D-75F974DAB899.jpeg

This Model K has a history back to the 1950's. It was owned by Nelson Hollywood, a well known collector at the time:...

Wondering if anyone from Georgia will be attending the Luray swap next month. As luck would have it, that is the weekend my in-laws are coming to visit so I can't make it.

I am looking for 3 stock wire wheels in REALLY good condition for my '26 pickup - I picked up 2 this weekend and they of course wound up being for Model A's. (If someone in...

I still have still not found any other old car owners in Klamath Falls area but that has not stopped me from having little tours of my own. A couple of weekends ago I set out to circumnavigate Stukel Mountain by Model T. Stukel towers some 2000' above the Klamath Basin floor and can be seen anywhere in the area. The picture was taken from my front...

I drive my T's a lot. Yesterday. after a short drive, I left my 1915 touring idling running on magneto while I ran in the house for no more than two minutes. When I came out, smoke was pouring out of the coil box. I shut her down and removed the coil box lid and found the number one coil had tar bubbling out of it. I'm guessing it shorted out? I...

This may seem like an OT thread at the beginning but it is Model T related at the end.

When I was in the Marines, in the Fleet Marine Force, we spent a lot of evening time polishing brass belt buckles for the next morning’s inspection. In 1974, I was selected for Embassy duty, AKA MSG Duty (Marine Security Guard). Basically, we were on loan to...

JUNE 19TH MODEL T HOMECOMING IN RICHMOND, IN. TOURS, CAR SHOW, SWAP MEET, SEMINARS, AND MORE. REGISTER TODAY TO RESERVE YOUR SWAP MEET SPACE!

I'm taking off the trunk and mounting the pickup box on my 1925 roadster. Does anyone have instructions, sketches, or images so I do it right?

A currently hot Jelf topic regarding restoration and originality contains an observation by Tim Juhl that has set me thinking. He said:

“Let us not forget that the Model T was one of the most customized cars of it's time.... often beginning soon after it rolled out of the factory. I consider my car's equipment to be part of it's history and have...

So I notice that my early steering bracket does not align with a 26-27 frame holes. Will a 26-27 Steering Bracket 3539DU work for a early steering column?

DC45CDF4-0356-4918-BCEE-9B0F6D05581B.jpeg 5D35D9DD-6A83-4058-815C-81A8A669FF36.jpeg 2D77F1CA-EF12-4909-8656-886E84584113.jpeg 8254C029-7EBB-4353-889A-E8F40E8C4F74.jpeg

Does this ring anyone’s bell? All brass, came with a bunch of carb parts. To me it looks like some sort of primitive carb, 6847BFF0-6921-4013-B722-8301764ABEEF.jpeg 3B857BC2-8CA9-4B48-AECE-2FF26DDE88CF.jpeg C72A725F-343E-4E84-9C7F-7EBD885BD520.jpeg D6C776E9-7A17-4DC4-BCBE-2AB9FFEAF250.jpeg

Anyone know what this hub cap fits? Painted what looks OD Green. Maybe 40’s military?
E4F5AD0C-CA2A-48C9-B106-8AE42D53BD3E.jpeg
5F968BE1-1868-4815-8704-A868EDA0A4EA.jpeg

Looks like drip painted, coating is thick. Any idea? Thanks Dan

23 Roadster..Does the coil box lid secure the coils in any way? I don't have a lid for mine, and had a coil loose connection at the bottom contact. That made me wonder if a lid would have prevented this from happening. That being said, does anyone have a slant style coil box lid for a 23 roadster? Thanks..Tommy.

The ruckstell in my 25 Tudor is stuck. Not sure, but I think it’s stuck in high. I can’t move the shifter forward or backwards. What should I do first? Is there a easy fix for this?

We all sometimes think of the car I should have kept and not sold. I have several in mind, 1965 Mustand convert, the 1932 B400, The 1909 right hand drive Model T Roadster and perhaps a few more (The 1918 Chev hardtop coupe is one.) What car should you have kept and not sold?

Joe Lappin Jr passed away this week at 91.

Most don’t know him as he was more regional/local.

How was a hero. Out of nowhere at age 80, Joe decided he wanted to own and drive a Model T for the first time! And he did!

He found a restoration in progress in an estate, bought it and proceeded to have the restoration done-his way.

It was a 27...

Eastern Idaho State Fair, Blackfoot, Idaho 1921
Model T front and center !

HELLO FELLOW CAR LOVERS,
IT'S BEEN A WHILE SINCE I POSTED ON OUR SITE, SO I WANT TO WISH ALL OUR VIEWERS A HAPPY EXODUS FROM THE COVID NIGHTMARE. I HOPE IT'S ALMOST OVER. I HAVE HAD SUCH FINE RESULTS FROM ALL MY POSTINGS, IT IS A PLEASURE TO BE BACK WITH THIS HAPPY ONE.
A WHILE BACK, A VERY FINE WOMAN FRIEND ASKED ME IF I WOULD DRIVE HER & HER...

We will be holding our annual spring Model T- Model A- prewar swap meet on April 17th at 7 A.M. at our farm 5 miles East of Kenyon, Mn. at 7525 Co. 12 Blvd. It is 50 miles south of St. Paul, Mn. It will be outside only. No setup charge. We have room for primitive camping the day-night before unless there is heavy rain. There will be a lunch wagon...

Thanks for any ideas. It's going to be in a thread and I'd like to be sure about the make and model.
Thanks,
Rob

1D5A043E-9878-4DC4-A3AD-A93A30013A44.jpeg

I am planning to prep and paint my car soon. My original paint plan was Windsor maroon. does anyone here have pictures of model ts with that color? also, i am going to paint the fenders and running boards black.

When I took these apart to get re-lined seemed the first pictured narrow band for reverse had the two straight slot ears and the second narrow band for slow speed had the two rivets. Does it matter which narrow band goes on the related drums, any input would be great.

First correct answer. Only one clue, it’s T Ford related. The first correct answer can have a choice of one of our spring loaded oil can holders, or my left kidney. I’m still using my right one. 3B0EF058-56E3-4466-A36B-BE903B4A18E5.jpeg

20210409_212024404_iOS.jpg when I was installing my classtique top on my touring I had the straps from langs for the front bow. Where they were so short and stiff it was difficult to tighten them evenly. It occured to me that a turnbuckle would woould be easier to adjust. I put on the turnbuckle from the hardware store and found it worked much...

Some old ads in one of my Ford supplier books from 1918-1919. Enjoy.

I am buying my first Model T this week. It is a touring car that was made in October of 1913 so it has a 1914 body style. The car was restored to be the way it came from the factory without a battery or electrical lights. I want to add a battery, turn signals and brake lights for safety.
.
I have two questions about about the simple light bulb...

My low speed jet is loose and rattles off set point. I was tired after running new engine in today in the shop. Collar seems to be loose that the jet sets in. I will take it apart tomorrow but figured I would ask tonight. High speed is fine. How is resistance held against the screw?
Thanks guys

I am just now getting to the water pump on my 08 model SR. The water pumps were built into the radiator similar to the first 2500 T's, but ran off a gear mounted on the flywheel which is on the front of the engine. Mesh was adjusted through rubber pads/shims on the radiator mounting. I found that the gear on the water pump shaft is Fiber. The gear...

60D47D8C-01C9-46B4-81E4-DC6C11AB80BA.jpeg BCB68BCA-2869-4490-9CE2-52F487B13E0E.jpeg 23452ED0-3AEF-4AF0-9C88-87660BA309B4.jpeg 709B19C3-952B-4CA5-A9D9-B2A0A407DED1.jpeg

There are several videos of installing new upholstery on u tube but none show what I need to see. They only show how to put the material onto the springs of the bottom cushion. How do you secure the backrest to the body? Is the upholstery secured to the backrest or only to the body? What keeps the backrest springs from moving around after you...

Original condition center door sedan passenger seat. $100.00 plus actual shipping cost.

E08C2642-AFBD-404A-8A4A-41AA55CBACAC.jpeg 3487B6CA-1E8C-47B8-B9CE-2C2D8E1CEF1B.jpeg BF9D29F8-54F7-454D-A709-94CEC5FCD529.jpeg 1781E4E5-87EB-4BAC-9D6F-D45C7F476BE9.jpeg

The 67th Long Beach Model T Club Swap Meet is scheduled for Saturday July 17, 2021 at Veteran's Stadium in Long Beach. MARK YOUR CALENDARS!! For Info contact Jeff Hood 562-597-5936 or moemechanic@aol.com or lbmtc.com

I have the best ever! New old stock Big Macs with old fashioned dark blue wide stripes. Heavy duty material. Still in the wrappers These are great and haven't been available for many years. $50.00 each plus $10.00 shipping. I have 2 pair. One is size 34 X 30 the other is size 56 X 32.

Saw this on AACA web site, thought it interesting. Anyone ever seen one of these? Dan

This is the Speedster in the upcoming Montana auction. I know it is of interest to Speedster guys and some would like to see these.
SpdstrMT9.jpg
SpdstrMT11.jpg
SpdstrMT1.jpg
SpdstrMT5.jpg
I asked the auctioneer to send them to me so we could share them. I have no connection with the sale. He felt there might be complaints if he posted...

One poster wanted to pre-sell items he was taking to the Tulare swap meet in May and I contacted him by mail and responded to his post. So far, no reaction. I am looking at getting an engine block from the meet to Richmond in the east bay area of San Francisco, or somewhere close enough for a courier pick-up. If anyone from the bay area is...

Is there anyone in the San Diego area that would be willing to drive their Model T to a school to let the children see one close-up. A friend of mine's daughter is learning about Henry Ford and he asked me to see if anyone would be willing to bring their vehicle to the school for a show and tell session. This would be a great opportunity to get...

Has anyone mounted one on a 26/27 yet? Column has horn wire channel which is right in the way of clamping it . :cry:

When this forum went to this new format years ago, one of the pro's of it was to be able to post pics of just about any size with no problems, as opposed to the old forum. Steve Jelf used to always promote that.
Seems lately tho, about 80% of the time I try to post a pic, of usual MB size , it gets tossed out because the PIXELS for Height and/or...

Does anyone know, or have the contact information, for the fellow who had the old BMW motorcycle that had the auxiliary rear axle setup that powered the sidecar? If so please share here. Thanks, Mike Lebsack

I won't even explain anything, the title says enough...

Hello all!

Would a Klaxon 18B Delco-Remy make a good ahooga horn for a 26 Touring? Time period correct?

Thanks,
Mike

Wondering what the word is on OCF for 2021?

I see that Motor Muster is moving forward

John

I took a pair of 14 windshield hinges apart to clean them up and found what looks like brass plating on the screws and nuts that hold hinges together. Spring inside the hinges looks to have copper plating on it. Has anyone ever seen that? Dan

I’m still fairly new with model Ts. I just purchased a 1915 roadster. I’m probably going to need to put a radiator on it as it has the original round tube on it. It’s not in the greatest shape and it probably leaks. I haven’t put water in it yet as the car has been sitting idle for About 49 years. Hard to believe I put gas in it and it started but...

I would like to build a replica of the #2 Ford car that was in the 1909 race. I am looking for information on how the body was constructed. Does anyone have plans of pictures of the body construction it would be greatly appreciated. This picture is a replica of a car driven in the 2009 race/ jputnam(at)wcoil.com

Model Ts from clubs are on a tour to the Joshua Tree area in Southern Cal. During the day, by the way the weather was just perfect, we saw several wrecked cars but no Model Ts. The only Ts were the seven cars on the tour.
4002CE91-9F42-4C5E-8639-763FD54C1039.jpeg
The roads into the park are all paved but once in the park we searched out dirt...

I picked up a Weaver axle stand at a local swap meet on Sunday. Tried looking up the model that I have and all I was able to find is the more deluxe version made by Weaver. does anyone have any factory or information on this model?

Carb runs great on new engine start, but dribbling a little fuel from the passage screws. They were a little loose but don’t want to snug them in until I ask. Not tapered and nothing to seal on the lip. I am thinking a touch of pipe dope maybe. 91CEE119-B52D-4B5E-8127-80967E763A7D.jpeg 8417E65E-E303-416E-9FB9-80FA983AC312.jpeg

A friend just bought a Model T speedster with buffalo wheels. He feels the caps are in bad condition, so he would like to replace these with better ones. Does anyone repop these or do we need to advertise for originals? I don't see them in any of my catalogs. What is a fair price? Are there left and rights? I am not a speedster guy, so this is new...

Could be beneficial for some of us.