MTFCA Forum

From ‘Ford Dealer and Service Field’ of November 1927.
I haven’t seen anything else quite like this. A useful accessory if it works. $65 in today’s money. However, The more I think about it, the more doubts I have. The actual bearing part must be shorter than normal, and that would have to be sized, bored, shimmed or scraped to suit the crank....

I have made several additions to the test rig that I have been playing around with this winter and have more in mind. I have added an AC volt/ammeter to the inverter supply to make it possible to monitor the power consumption with changes in flywheels weights and magnet types. One toggle switch allows me to change from operating the coil box to...

Hi…Has anyone ever used one?

Is anyone selling Michelin 30X3 1/2 tubes in the US?

Not to continue hijacking a different thread, I have found more photos of T parts in a salvage yard.
Also, Can anyone identify, or maybe help to identify this speedster body.

Thanks
Scott

IMG_4867.jpeg IMG_4791.jpeg IMG_4654.jpeg IMG_4928.jpeg

I recently completed rewinding a generator armature. Andre from Belgium and Ron Patterson encouraged me and offered advice to take on this project. Scott Conger offered several recommendations including a technique to eliminate any material shorting the segments. In addition to these people, several electric motor shop owners gave advice and...

A neat 'period' conversion barn find is up for sale locally. I thought you may be intrigued with the car to TT rear axle conversion that was done (these are the only pictures):

2279572650.jpg

2279115458.jpg

Cold, rainy and snowy Winter days are the perfect opportunity to learn or review the marvels of the Model T Ignition System and Model T Coils.
How they work and how to keep them running well.

The MTFCA Coil Testing and Tuning Webinar on Youtube:

Its worth viewing if you ever wondered about any of the following questions:
What are the major...

it is getting to be time to start planning our springtime auto. activities ... i spoke with Kevin Hammock this week regarding any changes in the Duncan swapmeet in March ... the only change is BIGGER ... the 2 north buildings are sold out and the building that was under construction last year is completed and will house an additional 100 plus...

Ed Larson was kind enough to teach me how an early 2 lever/2 pedal waterpump T shifts at the MTFCA Winter Clinic hosted by McPherson College (KS).

IMG_3232.jpeg

The ability to locate and correct car troubles quickly is a valuable asset to the repairman. That's what the good book says.

As the title says, however here's the link for it in the parts section as that's where it really belongs. Thanks

How do you guys attach new gas filter screen inside the “potato “?
Got some to replace and don’t want to reinvent the wheel. Thanks Dan

Thanks for all the advice to my prior post. As a follow up: I pulled the rim off the wheel to see what was going on.

1.All the nuts holding the hub to the to the backing plate. Every one was loose! I checked them all originally when I checked out the axle and bearings. I drove it around 20 miles since than and now they are all loose. I tightened...

I took this picture at work about a year ago. It's a little humerous to compare parts from my T to other things sometimes. For some reason I took my carb to work one day to mess with after hours. On the table was a different carburetor, a carburetor for a T-28, or more specifically an R-1820-86b.
I didn't take the cover off, not at a rebuild...

My 1909 Touring has a nasty habit of leaking oil all over the engine bay and undercarriage from the open valve train. Not only is the oil unsightly, but the oil is a pain to clean after just a short drive. To solve the problem, I made a leather valve cover that straps to the engine and the problem is now taken care of!! The leather cover has two...

Bottom Line Up Front:

Our local South Carolina Model T chapter is going to show their T’s to a local college that has an automobile history class (or similar title). Feb 2 or sometime close to that is the date.

Do any of you know of a 5 or 10 minute presentation with PowerPoint slides or pictures that I might be able to download or borrow?...

I'm new to the model T game so I'm just learning. What I'm learning so far is that this is a very expensive hobby! Ouch, anyway I have a 1926 Coupe with wood spokes. I just realized my spokes are loose. I'm finding different size tenon holes and lengths via the vendors. Is there a way to determine which ones I currently have so I can order spokes...

Just posted a new Model T road trip video from Fresno into the foothills of Central California—camping at the San Joaquin River Gorge, roadside brake adjustment, North Fork, and a run out to one of the disputed locations of California’s geographic center.

If nothing else, I really encourage you to watch the segment with Austin, an 18-year-old...

That time of year again!

Jan 16-17 2026 will be our schedule days!!

We have a block of rooms available at a discount of $99 a night at Hampton Inn in McPherson Kansas. Cut off to get your discounted room date is Dec 26th so book fast!

Can’t wait to see old and new faces!

Aaron Frazer

Hotel information:

200 N Centennial Dr
McPherson, KS...

I have Manifold Heater made by Visel-Darling Co. Inc. from Bronson Michigan.
I want to install it on my 1915 Centerdoor.
I'm wondering about the connection to the cab.
I assume there should be a floor grate/shut off that would mount on the floor boards using a flexible metal tube.
Any help/information is appreciated.

Dave

For half a century, members of the Rose City Model T Club have had access to Hand Cranked Coil Testers (HCCT) to tune up Model T coils. Nearly two decades ago, the club invested in a Strobo-Spark and it was a game changer. Today, the Electronically Cranked Coil Tester (ECCT) is available, which tests coils using dwell instead of amperage.

The...

It's been 11 years ago that posted looking for information to identify a carburetor. Turned out to be a Wizard or Simmons, no markings on it.

Since then that carburetor has been sitting on the shelf collecting dust. I'm now retired and thought I would take a shot at bringing it back to life.
The two things needed for it are the flapper and the...

What is the correct flywheel rpm when testing ?

Since the passing of Stan and Russ does anyone have a source of valve seats and floats for the Kingston 5 Ball Carb?

The Stan Howe setup work great. The float is from a Harley Davidson.

The 1909 float and seat aren’t original. The problem is the seat is some sort of plastic ball and it hangs up.

Any source would be greatly appreciated....

Hello everyone,

After being away for several years, I have decided to renew my membership and return to this forum with what will hopefully be received as a interesting project, worthy of members help.

Years ago I started a plan drawing of the Model T transmission, mostly because I wanted to know how such a simplistic mechanical device actually...

I recently saw the post about the frame riveting tool that sold on eBay and was curious if anyone has any information about the Stevens T-50 tool? It seems like a very helpful tool for our hobby. There was a picture of it from what looked like it came out of a catalog but most of the text was cut off and couldn't read the whole thing. I would also...

The Internet is changing so rapidly, even I have to scramble to keep up sometimes!
Now that Flash Player is no longer supported by any mainstream browsers, I had to change a lot of the code for my website. What does this have to do with Model T's I hear you ask? Simple, I had to (temporarily) remove the music library from my website until I could...

A friend is needing help mounting Budd wheels to model T.

Is there someone that he could call to get information he needs?

Thanks for the help.

What is the proper name for the type of fastener that is commonly used with sheet metal screws in applications where a nut and bolt can't be used. they ware always made of spring steel and can be flat or slightly curved with different sizes for different size screws and applications, I loked at McMaster-Carr but didn't really know what to call...

Last year I bought a very original early model year 1914 touring that has a late November 1913 engine. It has some transition parts like a two piece driveshaft and likely the original carburetor that was used for the 1913 model year, a Holley S. The car was in running condition when I got it, but for some reason, I really had a hard time getting...

This is a heavy casting. It’s apparent where it goes, but what is it for?

IMG_4714.jpeg IMG_4636.jpeg IMG_4713.jpeg IMG_4578.jpeg

Is there anyone near Waterford pa that has experience with the model T magneto ? I’m having issues with mine not having much charge on the magnets , have done the in cr flash with 3 batteries and a dc welder to no avail .
Thank you !

When I was putting the 22 into the garage for the winter, I couldn’t back it up my very low slope driveway. I had a bunch of things to do before I could get into it to find out what was up. I took the transmission cover off today and I can’t see anything wrong. The triple gears look fine, the drum shows no sign of heating or cracking, and what...

Happy New Year everyone! :)

Many of you will be aware by now of my Model T site, of which I'm pleased to say, gets a lot of comments about how useful people have found it.

I recently implemented a brand new feature on my Model T site, which I hope will get lots of use, and save a great deal of time!

Introducing the built-in search engine,...

F1 Drivers Race 100 Years Of Cars

Hi…..I can’t find a picture of one online, I think that they were made of canvas.

I have published a Worldwide index of Model T Ford clubs... which will no doubt have some entries missing :D
This index includes the websites of each Club, contact details and addresses where available.
If you know of any that need to be added, please let me know — please ensure you include a website address, physical address and contact...

Have a lowered 1913 Speedster project. Looking for different ways to mount a friction single lever shock to the rear axle.

I will mount the single lever friction shock parallel to the rear frame cross member.
These shocks have no name or markings. The shock has 2 rubber discs between the shock body and the adjustable tension lever. I am wondering...

Last week my 26 sedan ran so great but this week there’s a slight missing in the exhaust and a noticeable loss of power. And when I shut the engine off there’s a noticeable vapor coming out of the choke. 🫤 shorting out each spark plug seems to have no noticeable change in engine sound.

Will a 6 volt alternator putting out 40 amps charge a 8 volt battery...

1926 Touring, sudden-onset problem of slipping in high, but low and reverse are fine. Peeked inside for clues and found the clutch fingers quite loose. Had the clutch spring broken in service? Careful inspection showed it was intact, but...

After much puzzling I finally noticed that the clutch spring and spring cup were pushed right back the...

IMG_5241.jpeg This is the first time the carb has been off in 30+ years.

It’s an NH

What ‘magic’ was it supposed to do ? ( the coil spring)

Thanks in advance….

March 12-18 in Texas

Hello everyone. A very sad day here, Dick Hautzinger passed yesterday. I was very fortunate to know him for quite some time and travel to many swap meets, shows with him. I was always surprised by the amount of people that knew him wherever we traveled. His knowledge of Model T’s was endless.

A wonderful family man and friend to many that will...

Are the brake cam levers for a '26-'27 the same left and right?
I know the cams are different for each side.
Thank you

The time has come to pass the torch so to speak. I have taught my grandson the methods of babbitt pouring of model T main bearings and the procedure of boring and align reaming the bearings. I have been doing babbitt work for 40 years, but the time has come to share the knowledge with a younger person.

“Original” Smith just installed a side-mounted spare on his 1925 roadster pickup. Looks sharp, almost sporting - and really changes the look of the car.

I was in a local IKEA store and noticed they had cocoa floor mats for sale. The mats are perfect for the rear floor of 1910-1916 touring cars and are very reasonably priced. They are large enough so that they can be trimmed and fitted to the floor and look to be durable and nicely made. If you need a correct looking rear mat, this may be the...

Looking to buy 1 or more Weber 1910 wheel dollies. I have 3, looking to fill out the set and more would be great. Look at the pictures. I want a set for my unrestored 1911 open runabout. Thanks, Bob, 507 458 6778.

I recently dumped the pan for the first time on my T only to learn that the 'stock' engine I was promised actually has an A crank/ billet mains/ A rods/ and a big cam (you can imagine my surprise!)

Anyway, I think that the logical next thing to to is look into an OHV conversion. I'm too poor for a Rajo so the 1928 Chevy head seems like the...

IMG_4789.jpeg IMG_4475.jpeg IMG_4413.jpeg IMG_4492.jpeg

26 generator was functioning in the car.
On this car I have rebuilt the drive train, so I thought it would be a good idea to go over the starter and generator.
The previous owner had gone through the generator as it has a new insulated brush plate. The field coils are not new, however they are not grounded . Checked the armature on a growler,...

Last week my 26 sedan ran so great but this week there’s a slight missing in the exhaust and a noticeable loss of power. And when I shut the engine off there’s a noticeable vapor coming out of the choke. 🫤 shorting out each spark plug seems to have no noticeable change in engine sound.
I was hoping to post a short video of the fuel vapor coming...

My 1926 Roadster Pickup is 100 years old this month.
I drove it to the beach then drove it home in the rain.
IMG_8189.jpeg

-

Jan 9, 2026

Dear 2026 Bakersfield Swap Meet vendors and attendees,

For personal and practical reasons, it has been formally decided that I will no longer be spearheading the 2026 Bakersfield Brass Era/ PreWar Swap Meet. Therefore, all vendor fees received thus far, or by me in the future, will be returned via the self addressed stamped...

Looking for information on the manufacturer of these wheels. They have an odd tapered hubcap.

Got my notice from AACA for Hershey space renewal. First year since Blue field I will not have spaces at Hershey. Not worth it . I may still go but just to walk around. Go to keep going to Luray, better to me than Hershey. Hope to see you all there. Dan

Dec 5th 1925 was the 100th anniversary of the first Speedway meeting at the 5/6 mile banked concrete track at Maroubra, Sydney, Australia. Ted King raced his rajo there after quick repairs were carried out after his crash at Newcastle Speedway weeks before. It was a mad rush to put the car together over 7 weeks (without body) as best as I could...

In El Paso, IL.

Mark your calendar.

Registration forms are out.

Tin----Lizzy----one one seven at yahoo dot com (ignore the dashes)

Just a reminder that the annual old car swap meet in Marrietta, Ohio is Sat March 7th starting at 7:00 am. Lots of vendors with lots of model T and A stuff. Nice heated building with a nice lunch and pies and hot coffee. Vendors in attendance include Kevin Prus, David Nolting, Ron’s Machine Shop, The Carb Shed, The Coil Dr., with many individuals...

Constantly inspecting and cleaning up parts, I noticed something odd about my fan hub.
The belt hub itself spins true. The fan blades themselves spin true. However, the hub shaft and blade flange are spinning 0.097 off center!! The rivets for the blades were drilled true to shaft center, not with the flange.

Begs the question as to production...

Does anyone recognize these pressed steel brackets? Thanks for looking.

With all due respect, I am not looking for generic speculation but what I am looking for is what is considered authentic on the 'color' of Brass Glass Channel?

Was the Windshield Frame originally painted (dipped??) prior to installing the Glass Channel, -followed by the installation of the Windshield Glass, ...or was the Glass Channel installed...

Cleaning up parts on Daisy (1914 Touring), working on the front fender irons. The headlamp pickle forks are DB's, but I'm not familiar with the mark on the actual fender iron.
Anyone?

20260106_162601.jpg

My 1924 touring is having problems in performance. The #3 cylinder is not working correctly. Have replaced all plugs, wires, cleaned all contacts in coil box, rebuilt good coils. Good compression in all cylinders (40 - 44). Yet when you short out each cylinder, #1, #2, and #4 will short out the engine, but not at #3. All 4 will spark with a strong...

Saw this tool on a FB Vintage Tool I.D. Group, was unidentified by the poster.

So looked up the tool in a Stevens Speed Up Catalog. Rather useful to have when one-man replacing rivets, makes a real good bucking bar.

IMG_0357.jpeg

IMG_0358.jpeg

IMG_0356.jpeg

Would have liked that tool for last job on a crossmember, resorted to...

I have a question for the coil experts. I've been rebuilding some coils, checking the primary & secondary winding's, and replacing the capacitor. I am using both an old amp type tester and ECCT tester to set these up correctly. I've done about 10 so far and 5 have a strong spark and 5 a weak spark. The resistance of the primary & secondary...

Well, the last Model T of my more than 30 year hobby has left with a shipper to its new home. What started out as the first car I bought actually turned out to be the last one I fully restored. It was a 26/27 roadster Frankencar found in Idaho and I drove from Texas to pick it up with a flatbed trailer in February, needless to say NOT the time to...

Can someone help with the size and location to redrill the 4 th main oil hole, measurement from shoulder would be good. Trying to finish an engine my Dad built for me before he passed away. I can’t see any trace of the hole in the shell he had re babbited. Thanks

Having a Hard time posting to classified vehicles, please remove and relocate if necessary.

Here is a link to Facebook of a Martin-Parry bodied truck I have for sale.

If you are interested or have additional questions please give me a call at 314-287-1901.

I am trying to id the side lamp brackets on this 1914 Touring I recently acquired. I have gone through all of my reference materials and can't find a match to the brackets. Maybe aftermarket accessories? The car is a late August 14 build with a Hayes body. The side lamps are Victor Model 2. Thanks in advance for any help. 14T.jpg 14bracket.jpg

A local colector and restorer has bought my 1910. Also my wife of 57 years died Dec. 10.
I will give the buyer extra T Parts.

Does Jon ( RV’s brother) have a website? Thanks Dan

IMG_4514.jpeg IMG_4510.jpeg IMG_3883.jpeg IMG_4499.jpeg

What would a 4 wire switch harness be for?
Dash switch, non starter, mag headlights and horn car or truck?
I use to know but not sure now. Here is a picture
IMG_5105.jpeg
How about a 4 position terminal block. One terminal marked bat.
Thanks, Dan

I got these hinges with a basket case 24 touring that I bought. I know they are not for this car. Can anyone tell me if they are Model T

A client is rewooding a touring car, and he found that the blueprints he was given don't match with the wood in the body. Is there a reliable source for body wood blueprints?

IMG_0626.jpeg

I am restoring a 1914 T that will be getting a new firewall. When I restored our 1911 Touring, I used Laurel Mountain Forge antique cherry stain, based on recommendations on the forum site. It really is a good match for the original stain Ford used, when comparing it to the portions of the firewall that had been hidden for over 100 years.

This...

Happy new year everyone, I am beginning the top wood install on my 1924 Canadian Coupe. I would call this a top wood replacement but unfortunately there was no wood here to begin with. I have purchased a top wood kit from Snyder’s. If you guys have any input or possibly links to known good articles on the topic that could be of value to me it...

This is a common 1917-25 style spindle, but apparently a bearing cage or something came loose and cut a groove about 3/16 deep. Yes I know they don't make 'em anymore, but there are still a lot of these around. I just hate to throw it out if there's a chance someone might need it. Is it worth saving?

tspdlx01.jpg

Working on getting some anti tarnish coverings made for my car and a few friends. May even make these to sell. So far we have worked out fitted headlight covers for 13 14 models (earlier models will come soon) hub cap covers and speedo covers. Pototyping of the rad and cowl lamps are progressing. All covers are made of water proof black canvas...

I contacted the Benson Ford Library looking for the 1915 Runabout Side Curtain drawings, and the librarian said they need the correct part numbers. The parts list they referred me to has many that seem to fit the bill. Could anyone tell me what part numbers I should request?