How do YOU measure Hyatt bearings for tolerance

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
User avatar

Topic author
JTT3
Posts: 1348
Joined: Sun Jan 06, 2019 11:57 am
First Name: John
Last Name: Tannehill
Location: Hot Coffee, MS
MTFCA Number: 49460

How do YOU measure Hyatt bearings for tolerance

Post by JTT3 » Wed Aug 10, 2022 5:38 pm

…. …… ……. ……
Last edited by JTT3 on Thu Sep 01, 2022 8:17 pm, edited 3 times in total.

User avatar

TRDxB2
Posts: 5407
Joined: Tue Jan 08, 2019 4:56 pm
First Name: Frank
Last Name: Brandi
* REQUIRED* Type and Year of Model Ts owned: Speedster (1919 w 1926)
Location: Moline IL
Board Member Since: 2018

Re: How do YOU measure Hyatt bearing for tolerance

Post by TRDxB2 » Wed Aug 10, 2022 7:26 pm

If I can add to the thread. Can they be straightened & tightened by repining.
The past is a great place and I don't want to erase it or to regret it, but I don't want to be its prisoner either.
Mick Jagger

User avatar

Topic author
JTT3
Posts: 1348
Joined: Sun Jan 06, 2019 11:57 am
First Name: John
Last Name: Tannehill
Location: Hot Coffee, MS
MTFCA Number: 49460

Re: How do YOU measure Hyatt bearing for tolerance

Post by JTT3 » Wed Aug 10, 2022 7:34 pm

… …. …… …….
Last edited by JTT3 on Thu Sep 01, 2022 8:05 pm, edited 1 time in total.

User avatar

Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: How do YOU measure Hyatt bearings for tolerance

Post by Steve Jelf » Wed Aug 10, 2022 11:15 pm

Tightening loose cages: I've seen recommendations for and against. Fortunately I've always been able to find bearings that weren't loose. If I couldn't I'd look at past discussions and check the names. I take some people's Model T advice as golden. Others, not so much. :)
The inevitable often happens.
1915 Runabout
1923 Touring


Kevin Pharis
Posts: 1352
Joined: Thu Jan 10, 2019 3:54 pm
First Name: Kevin
Last Name: Pharis
Location: Sacramento CA

Re: How do YOU measure Hyatt bearing for tolerance

Post by Kevin Pharis » Wed Aug 10, 2022 11:22 pm

JTT3 wrote:
Wed Aug 10, 2022 7:34 pm
LOL of course but “it depends on what the definition of is is”
The greatest presidential quote of all time!!! 🤣🤣🤣

User avatar

Humblej
Posts: 1690
Joined: Sun Jan 06, 2019 12:23 pm
First Name: Jeff
Last Name: Humble
* REQUIRED* Type and Year of Model Ts owned: 1926 Canadian built coupe, 1924 TT C-cab, survivor 1924 roadster
Location: Charlevoix, Mi
MTFCA Number: 28034
Board Member Since: 2006

Re: How do YOU measure Hyatt bearings for tolerance

Post by Humblej » Thu Aug 11, 2022 6:52 am

I do not know of any other way than to measure the individual rollers at each end with a micrometer.

User avatar

Mark Gregush
Posts: 4956
Joined: Sat Jan 05, 2019 1:57 pm
First Name: Mark
Last Name: Gregush
* REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
Location: Portland Or
MTFCA Number: 52564
Board Member Since: 1999

Re: How do YOU measure Hyatt bearings for tolerance

Post by Mark Gregush » Thu Aug 11, 2022 10:25 am

Measure at each end of the roller, they can have a taper from wear.
I know the voices aren't real but damn they have some good ideas! :shock:

1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup

User avatar

Mark Nunn
Posts: 1105
Joined: Mon Jan 07, 2019 8:01 am
First Name: Mark
Last Name: Nunn
* REQUIRED* Type and Year of Model Ts owned: 1926 Runabout
Location: Bennington, NE
MTFCA Number: 50321
Board Member Since: 2017

Re: How do YOU measure Hyatt bearings for tolerance

Post by Mark Nunn » Thu Aug 11, 2022 1:29 pm

I have 5 Hyatt bearings from my spare rear end and pinion. I can mic them but I don't know what tolerances I should compare to. How small is considered usable?


speedytinc
Posts: 3838
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
MTFCA Number: 14383
Board Member Since: 2020

Re: How do YOU measure Hyatt bearings for tolerance

Post by speedytinc » Thu Aug 11, 2022 1:50 pm

Mark Nunn wrote:
Thu Aug 11, 2022 1:29 pm
I have 5 Hyatt bearings from my spare rear end and pinion. I can mic them but I don't know what tolerances I should compare to. How small is considered usable?
The std is .500 for axle & .562 for Drive shaft.
Supplies sleeves vary in thickness, so mating a thick sleeve with a more worn roller is great. I consider .498 or larger to be good with a 1.062 axle. That would be a tight cage & no splintering on the roller surface.
D.S. Thrusts on one side. Turn the spool accordingly & you are std. Any roller wear can be tightened in the gear mesh set up. Same deal, .560 is great for used.

I have been throwing out .005 or more wear. Undersize rollers must be solid, splinter free, but a little rust pitting is ok.
Last edited by speedytinc on Thu Aug 11, 2022 1:53 pm, edited 1 time in total.

User avatar

RajoRacer
Posts: 4305
Joined: Sun Jan 06, 2019 12:18 pm
First Name: Steve
Last Name: Tomaso
* REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1919 Centerdoor, 1924 TT C-Cab Express, 1925 Racer
Location: Longbranch, WA
MTFCA Number: 14972
MTFCI Number: 15411
Board Member Since: 2001

Re: How do YOU measure Hyatt bearings for tolerance

Post by RajoRacer » Thu Aug 11, 2022 1:52 pm

I have mic'd dozens and largest I've recorded was .499. With the new hardened sleeves, I've realized that near new - .497 - .499 rollers fit too tight. With a good used sleeve, one can run the larger sized rollers. One needs to optimize bearing to sleeve for best combination.

I also mic. both ends of the rollers.

User avatar

Darren J Wallace
Posts: 343
Joined: Sun Jan 06, 2019 11:43 am
First Name: Darren
Last Name: Wallace
* REQUIRED* Type and Year of Model Ts owned: 1913 Canadian Touring 1905 Queen model B
Location: Woodstock, Ontario, Canada
Board Member Since: 2005
Contact:

Re: How do YOU measure Hyatt bearings for tolerance

Post by Darren J Wallace » Thu Aug 11, 2022 2:30 pm

I’m going to be the devils advocate here. I’m a tool and die machinist just to throw that out there. Why do folks worry about these rollers being .005” small when there’s no way in hades that an entire rear axle housing runs within .010”. You may go to great lengths to straighten a housing in a lathe but the moment you hit a pothole or two, there’s no way housings stay straight. They bend and contort.
That being said, why does everyone treat these bearings like you’re setting connecting rod clearances?
Respectfully submitted, please explain what I’m overlooking.
Sorry for thread drift, I thought this was a good place to mention my thoughts about this.
1913 Canadian Touring & 1905 Queen, both cars are 4 generation family owned cars

User avatar

Topic author
JTT3
Posts: 1348
Joined: Sun Jan 06, 2019 11:57 am
First Name: John
Last Name: Tannehill
Location: Hot Coffee, MS
MTFCA Number: 49460

Re: How do YOU measure Hyatt bearings for tolerance

Post by JTT3 » Thu Aug 11, 2022 4:30 pm

….. …… ……….
Last edited by JTT3 on Thu Sep 01, 2022 7:51 pm, edited 1 time in total.

User avatar

Mark Gregush
Posts: 4956
Joined: Sat Jan 05, 2019 1:57 pm
First Name: Mark
Last Name: Gregush
* REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
Location: Portland Or
MTFCA Number: 52564
Board Member Since: 1999

Re: How do YOU measure Hyatt bearings for tolerance

Post by Mark Gregush » Thu Aug 11, 2022 4:34 pm

I am of the opinion, that many people try and set up the gear mesh too tight for how the rear end is designed. Even with good roller bearings and sleeves, there is still a lot of play for trying to get tight fits. The Model A is .015-.018 for ring gear to pinion.
I know the voices aren't real but damn they have some good ideas! :shock:

1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup

User avatar

A Whiteman
Posts: 992
Joined: Sun Jan 06, 2019 3:36 pm
First Name: Adrian
Last Name: Whiteman
* REQUIRED* Type and Year of Model Ts owned: 1926 TT, 1924 Colonial Roadster, 1924 'Bullnose' Morris, 1925 'Bullnose' Morris, 1936 JD AR
Location: South Island, New Zealand

Re: How do YOU measure Hyatt bearings for tolerance

Post by A Whiteman » Thu Aug 11, 2022 5:37 pm

That being said, why does everyone treat these bearings like you’re setting connecting rod clearances?
Good point.

My approach is to find a bearing that is as close as possible to standard (they never are so I take the best).
Locate the best sleeve (most of which are worn). Using NEW sleeves is possible but I have had issues with them not being properly hardened! (i.e. it should NOT be possible to scratch the inside of the sleeve with a slip of a screw driver..)
Calculate what shim is needed to close up the sleeve to get overall clearance as close to 'standard' as possible. Get the closest shim stock to that, make a shim to wrap around the outside of the sleeves. Install all carefully.

End result is a (least) worn Hyatt/sleeve with 'standard' clearance.

Remember when calculating the shim needed to HALVE the gap you are trying to close up to, as the shim will go on both sides of the sleeve it's thickness is effectively doubled when installed. (e.g. if the gap is 5 thou, use 2.5 thou shim).

That's how I do it - others may vary in their approach but "if it works, well, then it works".
Last edited by A Whiteman on Thu Aug 11, 2022 5:44 pm, edited 1 time in total.

User avatar

A Whiteman
Posts: 992
Joined: Sun Jan 06, 2019 3:36 pm
First Name: Adrian
Last Name: Whiteman
* REQUIRED* Type and Year of Model Ts owned: 1926 TT, 1924 Colonial Roadster, 1924 'Bullnose' Morris, 1925 'Bullnose' Morris, 1936 JD AR
Location: South Island, New Zealand

Re: How do YOU measure Hyatt bearings for tolerance

Post by A Whiteman » Thu Aug 11, 2022 5:42 pm

My approach is to wrap the shim around the sleeve, put a hose clamp over that and tighten to reduce the size, slide in the housing, mowing the hose clamp as needed.

It isn't easy and sometimes takes a couple of attempts (and replacement shim!) but it works.

Next slide the bearing in and check the clearance. I keep in mind that 'perfect' is not always necessary and does not actually offer significant benefit over 'reasonable' - in this situation.


Art M
Posts: 840
Joined: Wed Jun 19, 2019 12:57 pm
First Name: Art
Last Name: Mirtes
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring
Location: Huron, Ohio
MTFCA Number: 32489
MTFCI Number: 24068
Board Member Since: 2016

Re: How do YOU measure Hyatt bearings for tolerance

Post by Art M » Thu Aug 11, 2022 10:51 pm

Is there any interest in what Hyatt Product Engineering recommends for the rear wheel bearings. There are still some engineers around including the chief engineer at the time Hyatt discontinued manufacturing wound roller bearings.

Art Mirtes

User avatar

Duey_C
Posts: 1518
Joined: Sun Jan 06, 2019 12:28 pm
First Name: Duane
Last Name: Cooley
* REQUIRED* Type and Year of Model Ts owned: 18 Runabout, 24 Runabout for 20yrs, 25 TT, late Center Door project, open express pickup
Location: central MN
MTFCA Number: 32488
Board Member Since: 2015

Re: How do YOU measure Hyatt bearings for tolerance

Post by Duey_C » Fri Aug 12, 2022 2:11 am

Art, from my end of the peanut gallery ANY info from Hyatt would be very interesting.
Hyatt sold bearings to many mfgr's of other things than cars and are still being used and even worked sometimes.
Sorry, Off Topic: IH, TC and A-C come to mind. :)
Since I lost my mind mind, I feel more liberated

User avatar

Craig Leach
Posts: 1436
Joined: Tue Jan 08, 2019 12:22 am
First Name: craig
Last Name: leach
* REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
Location: Laveen Az
MTFCA Number: 26647

Re: How do YOU measure Hyatt bearings for tolerance

Post by Craig Leach » Fri Aug 12, 2022 8:47 pm

Adrian,
I have thought about shimming the bearing sleeves, but stumbled on what to use. Brass seems to be to soft (that's what my shim stock is) What material do you find works best for shims? How do you make a hole for greasing the bearing or make sure it lines up? Large hole?
I have found the biggest issue with bearing failure is not greasing the bearings after they are installed. I very rarely see anyone grease them on a tour & have had people ask why I do? The lube chart indicates every 200 mile if I remember correctly. I have had issues with the soft sleeves also they where so soft that they did no damage to the Hyatt's. I don't like the solid rollers they sell but have had good success with them on the inside. I have also had sleeves so small that I had to go threw all my Hyatt's to find some with enough wear to fit???? I have picked up some sleeves that are black and have found them to be thicker than some of the others and harder. I picked up a pair of used ones that have worn very well and will get used again some day.
Craig.

User avatar

A Whiteman
Posts: 992
Joined: Sun Jan 06, 2019 3:36 pm
First Name: Adrian
Last Name: Whiteman
* REQUIRED* Type and Year of Model Ts owned: 1926 TT, 1924 Colonial Roadster, 1924 'Bullnose' Morris, 1925 'Bullnose' Morris, 1936 JD AR
Location: South Island, New Zealand

Re: How do YOU measure Hyatt bearings for tolerance

Post by A Whiteman » Fri Aug 12, 2022 9:06 pm

Hi Graig,
Our shim stock from the engineering supplies is a tensile steel, available in various thicknesses. I keep a selection of sizes on hand.
As to the oiling holes. I punch a larger hole through the stock where the sleeve hole is before installing it - that allows a bit of movement in the shim, although once installed it rarely moves much. It does take a bit of fiddling to install the shim, but it can be done per my description.

Yes, reusing old ones is a better (IMHO) idea than using the soft new ones.

I don't like the solid rollers either, but you are correct in that they seem to be OK for the inner, probably because there is less flex at the inner end.

Cheers
Adrian

User avatar

Craig Leach
Posts: 1436
Joined: Tue Jan 08, 2019 12:22 am
First Name: craig
Last Name: leach
* REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
Location: Laveen Az
MTFCA Number: 26647

Re: How do YOU measure Hyatt bearings for tolerance

Post by Craig Leach » Sat Aug 13, 2022 12:39 am

Hi Adrian, I will look online for Tensile steel shim stock. I still have one more rear end to build and maybe another spare just incase if there is enough good parts left over. You can never have to many ready to install parts can you?
Craig.


Allan
Posts: 5201
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: How do YOU measure Hyatt bearings for tolerance

Post by Allan » Sat Aug 13, 2022 1:02 am

Mark, setting the crown wheel to pinion gear mesh by the gap between them ignores the need to set the correct rolling fit on each tooth. They are best meshed on rolling fit rarher than backlash. With that fit, the backlash looks after itself

I know that is not what the book says.

Allan from down under.

User avatar

RajoRacer
Posts: 4305
Joined: Sun Jan 06, 2019 12:18 pm
First Name: Steve
Last Name: Tomaso
* REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1919 Centerdoor, 1924 TT C-Cab Express, 1925 Racer
Location: Longbranch, WA
MTFCA Number: 14972
MTFCI Number: 15411
Board Member Since: 2001

Re: How do YOU measure Hyatt bearings for tolerance

Post by RajoRacer » Sat Aug 13, 2022 9:50 am

Adrian - we have hardened sleeves available here in the States - can you not access those ?

User avatar

A Whiteman
Posts: 992
Joined: Sun Jan 06, 2019 3:36 pm
First Name: Adrian
Last Name: Whiteman
* REQUIRED* Type and Year of Model Ts owned: 1926 TT, 1924 Colonial Roadster, 1924 'Bullnose' Morris, 1925 'Bullnose' Morris, 1936 JD AR
Location: South Island, New Zealand

Re: How do YOU measure Hyatt bearings for tolerance

Post by A Whiteman » Sun Aug 14, 2022 2:32 am

I actually source most of my parts direct from US dealers. The local NZ dealer also buys his stock from the same sources as well (it costs more to buy local, but they have stock on hand when you need it quickly). I do not recall which dealer the soft sleeves came from (they were bought a while ago).
I note US based folk have had the same problems. Bad batch maybe?


Jerry VanOoteghem
Posts: 2946
Joined: Sun Jan 06, 2019 4:06 pm
First Name: Jerry
Last Name: Van
Location: S.E. Michigan
MTFCA Number: 24868

Re: How do YOU measure Hyatt bearings for tolerance

Post by Jerry VanOoteghem » Sun Aug 14, 2022 7:09 pm

Darren J Wallace wrote:
Thu Aug 11, 2022 2:30 pm
I’m going to be the devils advocate here. I’m a tool and die machinist just to throw that out there. Why do folks worry about these rollers being .005” small when there’s no way in hades that an entire rear axle housing runs within .010”. You may go to great lengths to straighten a housing in a lathe but the moment you hit a pothole or two, there’s no way housings stay straight. They bend and contort.
That being said, why does everyone treat these bearings like you’re setting connecting rod clearances?
Respectfully submitted, please explain what I’m overlooking.
Sorry for thread drift, I thought this was a good place to mention my thoughts about this.
I agree with the points you make Darren. I believe however, that taper is at least as important, if not more so, than diameter. And, once you get more than .005 undersize, you also tend to pick up some taper as well. My belief is that, due to the differing circumference at each end of a tapered roller, the roller will tend to skew within the housing. The tendancy to skew then leads to a twist in the roller cage and also causes rubbing, instead of rolling, between the rollers and the axle shaft. From there, wear accelerates rapidly.


Jerry VanOoteghem
Posts: 2946
Joined: Sun Jan 06, 2019 4:06 pm
First Name: Jerry
Last Name: Van
Location: S.E. Michigan
MTFCA Number: 24868

Re: How do YOU measure Hyatt bearings for tolerance

Post by Jerry VanOoteghem » Sun Aug 14, 2022 7:10 pm

Allan wrote:
Sat Aug 13, 2022 1:02 am
Mark, setting the crown wheel to pinion gear mesh by the gap between them ignores the need to set the correct rolling fit on each tooth. They are best meshed on rolling fit rarher than backlash. With that fit, the backlash looks after itself

I know that is not what the book says.

Allan from down under.
Allan,

Thank for stating this! You are 100% correct!

Post Reply Previous topicNext topic