We shouldn't get in a hurry. It's human nature to goof off for 2 or 3 days and then get back to a project and want it done quickly. Perhaps it's because these thimbles don't show I forget I need them until it's too late. Putting the radiator on today I could only find one. The other disapeared or it wasn't there when I took the radiator off. They only cost a couple bucks but I didn't want to wait for an order so I made one today. It took about and hour and was kind of fun.
Rich
It resembles the rusty one because I made it too 7 years ago. I have them on my shopping list now.I got in a hurry.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 6796
- Joined: Fri Jan 04, 2019 10:51 am
- First Name: Richard
- Last Name: Eagle
- * REQUIRED* Type and Year of Model Ts owned: 1909 TR 1914 TR 1915 Rd 1920 Spdstr 1922 Coupe 1925 Tudor
- Location: Idaho Falls, ID
- MTFCA Number: 1219
- Contact:
I got in a hurry.
When did I do that?
-
- Posts: 913
- Joined: Mon Jan 07, 2019 1:32 am
- First Name: Ignacio
- Last Name: Valdes
- * REQUIRED* Type and Year of Model Ts owned: 1924 Touring
- Location: Houston, Tx
- MTFCA Number: 50406
- Board Member Since: 2016
Re: I got in a hurry.
So now I cannot unsee this. Is that roof flashing metal? Put a socket inside and peen it over to fold the top then cut the fins then put it in another socket and bend the 'fins' over?
-
Topic author - Posts: 6796
- Joined: Fri Jan 04, 2019 10:51 am
- First Name: Richard
- Last Name: Eagle
- * REQUIRED* Type and Year of Model Ts owned: 1909 TR 1914 TR 1915 Rd 1920 Spdstr 1922 Coupe 1925 Tudor
- Location: Idaho Falls, ID
- MTFCA Number: 1219
- Contact:
Re: I got in a hurry.
I believe it is just 22 gauge sheet steel left over from building some fenders or top iron sleeves. Fortunately there always seems to be a socket (or wrist pin) the right size.
When did I do that?
-
- Posts: 190
- Joined: Sun Jan 06, 2019 10:11 pm
- First Name: Thomas
- Last Name: Miller
- * REQUIRED* Type and Year of Model Ts owned: 16, 24, 26 Touring - 26 Roadster and Fordor
- Location: Livonia MI near Dearborn
- MTFCA Number: 14069
- Board Member Since: 2006
Re: I got in a hurry.
You do nice work. I've used my sockets on occasion for light press work but never a fabrication like that.
Tom Miller
One who cannot find beauty in an engine cannot find beauty in the universe.
One who cannot find beauty in an engine cannot find beauty in the universe.
-
- Posts: 892
- Joined: Sun Jan 06, 2019 12:28 pm
- First Name: James
- Last Name: Bartsch
- * REQUIRED* Type and Year of Model Ts owned: '26 Coupe
- Location: Dryden, NY 13053
- MTFCA Number: 30615
- MTFCA Life Member: YES
Re: I got in a hurry.
Richard: I'm surprised ( shocked, actually) that you do not maintain a pre-rusted inventory of that particular sheet metal so the finished parts match the car better. Nice work on the part by the way, I continue to enjoy your posts, pics, and artwork. best, jb
-
Topic author - Posts: 6796
- Joined: Fri Jan 04, 2019 10:51 am
- First Name: Richard
- Last Name: Eagle
- * REQUIRED* Type and Year of Model Ts owned: 1909 TR 1914 TR 1915 Rd 1920 Spdstr 1922 Coupe 1925 Tudor
- Location: Idaho Falls, ID
- MTFCA Number: 1219
- Contact:
Re: I got in a hurry.
I have turned shafts specific sizes to use that way but in a hurry the sockets are close enough. I have only ruined a couple and that was in the press. Sockets are cheap at the secondhand store.
That thimble will be suitably rusted next time I see it. I sacrificed a ruined slash apron with rust on it for items of that thickness. I also got a discount on a full sheet of rusty 22 gauge from the steel shop but chose to use a small piece of "new" for this piece.
Bending steel is such a pleasure. (Perhaps a Superman quote).
That thimble will be suitably rusted next time I see it. I sacrificed a ruined slash apron with rust on it for items of that thickness. I also got a discount on a full sheet of rusty 22 gauge from the steel shop but chose to use a small piece of "new" for this piece.
Bending steel is such a pleasure. (Perhaps a Superman quote).
When did I do that?