What safety wire?

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
User avatar

Topic author
Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

What safety wire?

Post by Steve Jelf » Fri Feb 19, 2021 2:00 pm

The .020" safety wire I have is too easily broken to suit me. Of course no local stores sell safety wire of any size at all. So before I go shopping online I'll ask here. What do you old hands at Model T reassembly recommend?
The inevitable often happens.
1915 Runabout
1923 Touring


FATMAN
Posts: 1650
Joined: Sat Jan 19, 2019 9:28 am
First Name: ROBERT
Last Name: BERGSTADT
Location: LOVES PARK IL
MTFCA Number: 1575

Re: What safety wire?

Post by FATMAN » Fri Feb 19, 2021 2:20 pm

Menards has some good stiff wire that ties and twist pretty good, Bob

User avatar

RajoRacer
Posts: 4308
Joined: Sun Jan 06, 2019 12:18 pm
First Name: Steve
Last Name: Tomaso
* REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1919 Centerdoor, 1924 TT C-Cab Express, 1925 Racer
Location: Longbranch, WA
MTFCA Number: 14972
MTFCI Number: 15411
Board Member Since: 2001

Re: What safety wire?

Post by RajoRacer » Fri Feb 19, 2021 2:25 pm

Aviation stainless steel - comes in assorted gauge.

User avatar

Topic author
Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: What safety wire?

Post by Steve Jelf » Fri Feb 19, 2021 2:33 pm

Aviation stainless steel - comes in assorted gauge.

Yes, that's what I have, but the .020" is too easily broken. That's why I asked. What size works best?
The inevitable often happens.
1915 Runabout
1923 Touring

User avatar

Pep C Strebeck
Posts: 519
Joined: Sun Jan 06, 2019 11:12 am
First Name: Joseph
Last Name: M
Location: MI
MTFCA Number: 0

Re: What safety wire?

Post by Pep C Strebeck » Fri Feb 19, 2021 2:51 pm

I have always used the 0.041" diameter wire with no problems, it works/fits for every location on the T. I definitely would not use anything less than the 0.032" diameter wire, but I prefer the 0.041" diameter. As you have stated, the 0.020" diameter will break too easily.
"Remember son, there are two ways to do this: The right way, and your way” Thanks Dad, I love you too.

LOOKING FOR A LUFKIN No. 9A Height Gage Attachment.


DHort
Posts: 2461
Joined: Sun Jan 06, 2019 1:30 pm
First Name: Dave
Last Name: Hjortnaes
* REQUIRED* Type and Year of Model Ts owned: 24 Speedster, 20 touring
Location: Men Falls, WI
MTFCA Number: 28762
MTFCI Number: 22402

Re: What safety wire?

Post by DHort » Fri Feb 19, 2021 2:53 pm

Adam told me to get the 0.041, so that is what I have.


kmatt2
Posts: 558
Joined: Wed Jun 17, 2020 1:41 pm
First Name: Kevin
Last Name: Matthiesen
* REQUIRED* Type and Year of Model Ts owned: 26 T Coupe, 16 T Open Express, 21 TT Flatbed. 15 T Roadster, 13 & 25 T Speedster , 51 Mercury 4 door sport sedan, 67 Mercury Cougar
Location: Madera CA 93636
MTFCA Number: 11598

Re: What safety wire?

Post by kmatt2 » Fri Feb 19, 2021 3:02 pm

Steve, In a pinch and if you can't get what you want locally try a building materials store that sells rebar. They should sell wire for tieing rebar. I don't know if it will meet your needs but you could check a local store. I have a large role of stainless steel safety wire I bought at Harbor Freight and it lasts a long time, so where ever you buy it on line get enough to last a while.


Rajo23
Posts: 59
Joined: Sun Jan 06, 2019 10:30 pm
First Name: John
Last Name: Goertzen
* REQUIRED* Type and Year of Model Ts owned: 1923 Touring, 1927 Runabout
Location: Canby, OR
MTFCA Number: 50634

Re: What safety wire?

Post by Rajo23 » Fri Feb 19, 2021 3:05 pm

Try this:

https://shop.vansaircraft.com/cgi-bin/s ... afety-wire

Full disclosure: I have the pleasure of working at Van's.

User avatar

Topic author
Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: What safety wire?

Post by Steve Jelf » Fri Feb 19, 2021 3:19 pm

Excellent! There's a HF store just a half hour down the road. That will save me some time. Thanks to all.

https://www.harborfreight.com/search?q= ... ock%20wire
Attachments
Screen Shot 2021-02-19 at 2.17.55 PM.png
The inevitable often happens.
1915 Runabout
1923 Touring


otrcman
Posts: 364
Joined: Sun Jan 06, 2019 2:25 pm
First Name: Dick
Last Name: Fischer
* REQUIRED* Type and Year of Model Ts owned: 1912 Touring
Location: Arroyo Grande, CA

Re: What safety wire?

Post by otrcman » Fri Feb 19, 2021 3:29 pm

Aviation safety wire as mentioned by others is good stuff. It is quite malleable and not as prone to breakage from twisting as other wires. Since we're talking aviation grade stainless safety wire, a good size guide is the FAA aviation mechanics manual AC 43.13-1B. Here is what the good book has to say:

"b. When using double-twist method of safety wiring, .032 inch minimum diameter wire should be used on parts that have a hole diameter larger than .045 inch. Safety wire of .020 inch diameter (double strand) may be used on parts having a nominal hole diameter between .045 and .062 inch with a spacing between parts of less than 2 inches. When using the single-wire method, the largest size wire that the hole will accommodate should be used......."

Notice that there is no specific mention of .041 wire in that paragraph, although the .032 is specified as a miniumum. The only specific mention of .041 is in the section on safety wiring cable turnbuckles and propellor mounting bolts. Since Model T's don't use propellors or control cables, you could just stick to .032 and be good to go.


Luke
Posts: 585
Joined: Fri Dec 13, 2019 1:04 am
First Name: Luke
Last Name: P
* REQUIRED* Type and Year of Model Ts owned: 1926
Location: New Zealand

Re: What safety wire?

Post by Luke » Fri Feb 19, 2021 4:52 pm

@Steve Jelf - I'm a little interested as to exactly what use on your T this is intended for?

My reason for asking is that I seem to recall some discussion around lock wire disintegrating on gudgeon pinch bolts, hence people using split pins?

I've not looked, but I expect that discussion would be easily found. I've no particular view on this myself, but having used lock wire on many aeroplanes (without issue) I was interested to hear of this apparent issue.

If it is really a 'thing' then it seems to me it might be worth further research if you were intending using the wire internal to the engine.

User avatar

jsaylor
Posts: 335
Joined: Sun Jan 06, 2019 5:25 pm
First Name: John
Last Name: Saylor
* REQUIRED* Type and Year of Model Ts owned: 1921 Touring, 1927 Tudor
Location: Citrus Heights, Ca
MTFCA Number: 1695
MTFCI Number: 23870
Board Member Since: 1999

Re: What safety wire?

Post by jsaylor » Fri Feb 19, 2021 6:17 pm

Luke: The only place externally to use safety wire, as far as I can remember, is the wishbone studs under the pan. You have to wire the two stud nuts together to keep hem from packing out of the pan. Internally there are several in the transmission and ring gear bolts in the rear end.


kmatt2
Posts: 558
Joined: Wed Jun 17, 2020 1:41 pm
First Name: Kevin
Last Name: Matthiesen
* REQUIRED* Type and Year of Model Ts owned: 26 T Coupe, 16 T Open Express, 21 TT Flatbed. 15 T Roadster, 13 & 25 T Speedster , 51 Mercury 4 door sport sedan, 67 Mercury Cougar
Location: Madera CA 93636
MTFCA Number: 11598

Re: What safety wire?

Post by kmatt2 » Fri Feb 19, 2021 6:40 pm

Safety wire used on many more locations on pre 1921 cars. The closed driveshaft spool, the front engine mount engine pan nose cap are two that I can think of.

User avatar

jsaylor
Posts: 335
Joined: Sun Jan 06, 2019 5:25 pm
First Name: John
Last Name: Saylor
* REQUIRED* Type and Year of Model Ts owned: 1921 Touring, 1927 Tudor
Location: Citrus Heights, Ca
MTFCA Number: 1695
MTFCI Number: 23870
Board Member Since: 1999

Re: What safety wire?

Post by jsaylor » Fri Feb 19, 2021 6:47 pm

Oh Ya. That closed drive shaft spool, studs instead of bolts. Out of sight out of mind.


Allan
Posts: 5205
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: What safety wire?

Post by Allan » Fri Feb 19, 2021 7:53 pm

...and the two lower bolts at the fourth main.
The soft pliable wire used in wire tie hay balers is very handy. When not using it for safety wiring, it makes a good oxy welding filler rod. Just don't try using it for bailing out your boat. :D

Allan from down under.


It's Bill
Posts: 279
Joined: Mon Jan 07, 2019 6:41 pm
First Name: Bill
Last Name: Hoffer
Location: Mars, PA
MTFCA Number: 32571
MTFCI Number: 24364
Board Member Since: 2016

Re: What safety wire?

Post by It's Bill » Fri Feb 19, 2021 8:07 pm

Langs lists .040 stainless wire for a buck and a half in theit hardware section near the back of the (old) book. Cheers, Bill


Luke
Posts: 585
Joined: Fri Dec 13, 2019 1:04 am
First Name: Luke
Last Name: P
* REQUIRED* Type and Year of Model Ts owned: 1926
Location: New Zealand

Re: What safety wire?

Post by Luke » Fri Feb 19, 2021 8:21 pm

Just in case anyone's interested I found a couple of the threads where (for gudgeon/wrist pins) the use of lock wire vs split pins vs lock washers was mentioned:

viewtopic.php?f=2&t=9272

viewtopic.php?f=2&t=6381

I wouldn't say it was discussed widely, nor in depth, however it's something that is perhaps worth thinking about.


2nighthawks
Posts: 406
Joined: Sun Jul 21, 2019 2:53 am
First Name: Harold
Last Name: Schwendeman
* REQUIRED* Type and Year of Model Ts owned: '23 Roadster Pickup, '26 Touring, '27 Depot Hack, '23 Roadster
Location: Seattle
MTFCA Number: 0
Board Member Since: 2005

Re: What safety wire?

Post by 2nighthawks » Fri Feb 19, 2021 8:39 pm

Hmmm,....call me crazy, but somehow, the two terms,...."safety wire" and Harbor 'Freight don't quite sound quite right to me!

User avatar

BE_ZERO_BE
Posts: 541
Joined: Sun Jan 06, 2019 12:27 pm
First Name: BOB
Last Name: CASCISA
* REQUIRED* Type and Year of Model Ts owned: 1916 TOURING
Location: POULSBO, WA
MTFCA Number: 16897
MTFCI Number: 16628

Re: What safety wire?

Post by BE_ZERO_BE » Fri Feb 19, 2021 8:51 pm

I use .032" stainless steel aircraft safety wire throughout ... engine, transmission and rear end.

If you want a challenge you can use .041"
And if you are a glutton for punishment, use .062" :lol:
Respectfully Submitted,
Be_Zero_Be

I drive a Model T ... Microseconds don't matter :D

For every Absolute Model T Fact there are at least three exceptions.


otrcman
Posts: 364
Joined: Sun Jan 06, 2019 2:25 pm
First Name: Dick
Last Name: Fischer
* REQUIRED* Type and Year of Model Ts owned: 1912 Touring
Location: Arroyo Grande, CA

Re: What safety wire?

Post by otrcman » Fri Feb 19, 2021 9:47 pm

2nighthawks said

"Hmmm,....call me crazy, but somehow, the two terms,...."safety wire" and Harbor 'Freight don't quite sound quite right to me!"

I wasn't going to say it Harold, but dittos ! The real thing is only a buck more.

Dick

User avatar

Topic author
Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: What safety wire?

Post by Steve Jelf » Fri Feb 19, 2021 10:45 pm

I'm a little interested as to exactly what use on your T this is intended for?

The places I have in mind immediately are the four mag ring bolts and the four flywheel bolts. For the wishbone and the lower ball cap bolts I use the Standard Ford Repair Kit — ordinary baling wire.
The inevitable often happens.
1915 Runabout
1923 Touring

User avatar

Kaiser
Posts: 1028
Joined: Mon Jan 07, 2019 5:32 am
First Name: Leo
Last Name: van Stirum
* REQUIRED* Type and Year of Model Ts owned: 1923 Huckster, '66 CJ5 daily driver
Location: Netherlands
Board Member Since: 2016

Re: What safety wire?

Post by Kaiser » Sat Feb 20, 2021 11:09 am

Aircraft Safety Wire is annealed stainless steel, the annealing makes it less prone to fatigue and easier to bend without breaking
0.032 is most commonly used on Ts but 0.041 works fine too.
And try to buy or borrow the special pliers for it, it makes the work a lot easier and neater !!
Attachments
tang.jpg
tang.jpg (6.22 KiB) Viewed 3082 times
When in trouble, do not fear, blame the second engineer ! 8-)
Leo van Stirum, Netherlands
'23 Huckster, '66 CJ5 daily driver

User avatar

Mark Gregush
Posts: 4957
Joined: Sat Jan 05, 2019 1:57 pm
First Name: Mark
Last Name: Gregush
* REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
Location: Portland Or
MTFCA Number: 52564
Board Member Since: 1999

Re: What safety wire?

Post by Mark Gregush » Sat Feb 20, 2021 11:16 am

Funny how long the plain old type non stainless steel wire lasted for all those years! ;) Not all stainless is non magnetic, so you might want to check if first if you use. Yes I do use stainless on the inside, well most of the time.
I know the voices aren't real but damn they have some good ideas! :shock:

1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup


jab35
Posts: 892
Joined: Sun Jan 06, 2019 12:28 pm
First Name: James
Last Name: Bartsch
* REQUIRED* Type and Year of Model Ts owned: '26 Coupe
Location: Dryden, NY 13053
MTFCA Number: 30615
MTFCA Life Member: YES

Re: What safety wire?

Post by jab35 » Sat Feb 20, 2021 12:20 pm

fwiw, when removing the differential from my coupe yesterday I found the bottom two ball cap-engine pan bolts 'secured' with two strands of #22 copper magnet wire. The wire plus vintage crud kept those tight. Not a recommendation. I see Lang's has small quantities of 0.040" safety wire in their catalog.


Allan
Posts: 5205
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: What safety wire?

Post by Allan » Sat Feb 20, 2021 10:04 pm

Am I wrong in thinking that safety wiring is done to stop bolts/nuts from backing off? I cannot see how it can reliably maintain tension on the nut/bolt to stop it loosing tension. As long as the wire stays in place, it is doing its job.

Allan from down under.


jiminbartow
Posts: 2202
Joined: Sun Jan 06, 2019 10:55 pm
First Name: James
Last Name: Patrick
* REQUIRED* Type and Year of Model Ts owned: 1926 Coupe
Location: Bartow, FL
MTFCA Number: 50126
Board Member Since: 2001

Re: What safety wire?

Post by jiminbartow » Sat Feb 20, 2021 11:38 pm

Safety wire, if done right will maintain tension on bolts and prevent them from loosening. See: www.mtfca.com/discus/messages/29/48566.html. Jim Patrick


Allan
Posts: 5205
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: What safety wire?

Post by Allan » Sun Feb 21, 2021 8:18 am

Thanks Jim. I can see how that will work, but I'd like to see evidence that that is how it was done on the production line. My gut feeling is that the safety wiring done on T's was just done to achieve the same result as split pins on castle nuts, to stop the nut backing off. We have the time to do it better when restoring, but it may be a case of over thinking it. This is totally understandable in the aviation industry where absolute safety is the pursuit. But, what might be the consequences of the two spring loaded nuts on the front wishbone backing off part of 1/6th of a turn?

Allan from down under.

Allan from down under.

Post Reply Previous topicNext topic