Gates Fan Belt Size

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
J1MGOLDEN
Posts: 945
Joined: Sun Jan 06, 2019 5:39 pm
First Name: James
Last Name: Golden
* REQUIRED* Type and Year of Model Ts owned: 1926 Model T Roadster
Location: Bowie, MD
MTFCA Number: 14294
MTFCI Number: 13562

Gates Fan Belt Size

Post by J1MGOLDEN » Wed Feb 01, 2023 7:25 am

Like the Doc said, "You got it again son!"

My problem is with a 1920 engine.

The two different sized crankshaft pulleys are listed for 1920, one at the end and one at the beginning of years they fit.

I used the larger size pulley that should make the fan turn slightly faster!!

I'm wondering if a Gates 820 flat black belt was intended for use on the 1920 new size crankshaft pulley.

The Gates 819 belt that I installed is just long enough to let the fan hit the lower water outlet.

None of those belts are listed by length in any of the supplier catalogs for some reason!


Adam
Posts: 1411
Joined: Sun Jan 06, 2019 11:57 am
First Name: Adam
Last Name: Doleshal
* REQUIRED* Type and Year of Model Ts owned: ‘13 Touring, ‘24 Touring, ‘25 TT dump truck, ‘26 Tudor, ‘20 Theiman harvester T powerplant, ‘20 T Staude tractor
Location: Wisconsin
MTFCA Number: 23809
MTFCI Number: 1
Board Member Since: 2000

Re: Gates Fan Belt Size

Post by Adam » Wed Feb 01, 2023 11:19 am

The small crankshaft pulley is for the earlier small fan hub.

The large crankshaft pulley is for the later large fan hub.

Using the large crankshaft pulley with the small fan hub just makes the fan go too fast, it really doesn’t cool any better. It’s likely to create more problems.
-The fan bearings aren’t designed for the faster speed and wear faster.
-The fan isn’t balanced for the higher speed. The blades are riveted on and vibration is what cracks them. When an early fan blade breaks, it often significantly damages the radiator core.
-The fan really only needs to be effective from an idle speed up to maybe 10 mph. After that, your forward motion moves all the air thru the radiator, not your fan. Any higher fan speed over that is just wasted.


Adam
Posts: 1411
Joined: Sun Jan 06, 2019 11:57 am
First Name: Adam
Last Name: Doleshal
* REQUIRED* Type and Year of Model Ts owned: ‘13 Touring, ‘24 Touring, ‘25 TT dump truck, ‘26 Tudor, ‘20 Theiman harvester T powerplant, ‘20 T Staude tractor
Location: Wisconsin
MTFCA Number: 23809
MTFCI Number: 1
Board Member Since: 2000

Re: Gates Fan Belt Size

Post by Adam » Wed Feb 01, 2023 11:27 am

Also, I just looked and the Gates belts go from 25+7/8” to 27”. That’s it. Nothing in between. 25+7/8” is for black radiators with small cs pulley and small fan pulley. 27” is for large cs pulley and large fan pulley up to 1925 prior to the fan being part of the water outlet connection.

User avatar

Oldav8tor
Posts: 1930
Joined: Sun Jan 06, 2019 11:39 am
First Name: Tim
Last Name: Juhl
* REQUIRED* Type and Year of Model Ts owned: 1917 Touring
Location: Thumb of Michigan
MTFCA Number: 50297
MTFCI Number: 24810
Board Member Since: 2018

Re: Gates Fan Belt Size

Post by Oldav8tor » Wed Feb 01, 2023 11:55 am

I checked the Gates site for Vintage Automotive belts. This is what I found:
belts.jpg
1917 Touring
1946 Aeronca Champ
1952 Willys M38a1 Jeep (sold 2023)
1953 Ford Jubilee Tractor

User avatar

Steve Jelf
Posts: 6463
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
* REQUIRED* Type and Year of Model Ts owned: 1923 touring and a few projects
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: Gates Fan Belt Size

Post by Steve Jelf » Wed Feb 01, 2023 12:42 pm

I expected that the change from little pulley to big pulley would coincide with the change from narrow nose pan to wide nose. But the pan changed in 1917 and the bigger pulley came three years later.
The inevitable often happens.
1915 Runabout
1923 Touring


Allan
Posts: 5205
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Gates Fan Belt Size

Post by Allan » Wed Feb 01, 2023 6:20 pm

I believe you are correct about the pan change Steve, but the pulley changes came later. The large crank pulley needs to run with the larger alloy fan pulley. The change was very likely made as a cost saving. The new fan blade is much simpler to manufacture.

All from down under.

User avatar

Craig Leach
Posts: 1436
Joined: Tue Jan 08, 2019 12:22 am
First Name: craig
Last Name: leach
* REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
Location: Laveen Az
MTFCA Number: 26647

Re: Gates Fan Belt Size

Post by Craig Leach » Wed Feb 01, 2023 9:59 pm

Hi James, I run the poly grooved belts sometimes called serpentine they seem to last very long. Don't look write because of the grooves.
Common sizes are K0 then the # of grooves then 0 & the size in inches so a K060280 is a 6 groove & 28" long around the outside.
Craig.


Topic author
J1MGOLDEN
Posts: 945
Joined: Sun Jan 06, 2019 5:39 pm
First Name: James
Last Name: Golden
* REQUIRED* Type and Year of Model Ts owned: 1926 Model T Roadster
Location: Bowie, MD
MTFCA Number: 14294
MTFCI Number: 13562

Re: Gates Fan Belt Size

Post by J1MGOLDEN » Thu Feb 02, 2023 9:08 pm

I just ordered and 821 from Langs that might work OK.


Topic author
J1MGOLDEN
Posts: 945
Joined: Sun Jan 06, 2019 5:39 pm
First Name: James
Last Name: Golden
* REQUIRED* Type and Year of Model Ts owned: 1926 Model T Roadster
Location: Bowie, MD
MTFCA Number: 14294
MTFCI Number: 13562

Re: Gates Fan Belt Size

Post by J1MGOLDEN » Fri Feb 03, 2023 5:33 pm

I got an 813 for some reason!


Topic author
J1MGOLDEN
Posts: 945
Joined: Sun Jan 06, 2019 5:39 pm
First Name: James
Last Name: Golden
* REQUIRED* Type and Year of Model Ts owned: 1926 Model T Roadster
Location: Bowie, MD
MTFCA Number: 14294
MTFCI Number: 13562

Re: Gates Fan Belt Size

Post by J1MGOLDEN » Sun Feb 05, 2023 5:08 pm

That was an 816, not a 813 and now I know a Gates 816 is 28 7/8th inches long and will fit a 1916 to 1918 with a larger crankshaft pulley.


ShirkWood
Posts: 48
Joined: Sun Jan 06, 2019 9:27 pm
First Name: Verne
Last Name: Shirk
Location: Kansas

Re: Gates Fan Belt Size

Post by ShirkWood » Fri Feb 10, 2023 2:51 pm

I run a small fan hub with a large crankshaft pulley on a c.1920 engine in our 1914. Have done so for about 25 years. Not my choice...the engine was built for a speedster and ended up in the 1914. I could not find the correct length belt for that combination. I ended up using an idler arm/bearing off of a distributor that John Stoltz sold, mounted to the timing gear cover. This allowed me to use a longer belt I could find. I put a modern sealed ball bearing pack in the fan, and have changed it once, just in case the bearings were going bad. They were sealed bearings and subject to the heat of the engine/radiator, so I figured it needed a change. Early original brass hub fans, which the 1914 should have, were not made so that you could install the ball bearing pack so I used a later small steel fan hub. I think these modern ball bearing packs are still available for the small hub fans...I have not checked lately. I threw a fan blade once with it. Probably more my fault for not checking on it, than it was a fault of the higher speed created with a large crank pulley. I run a cog belt and have had no problems with it. I cruise at about 35-38 mph and drive it quite a bit.

Post Reply Previous topicNext topic