Using a 4-1 steering gear box in place of 5-1
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 4967
- Joined: Sat Jan 05, 2019 1:57 pm
- First Name: Mark
- Last Name: Gregush
- * REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
- Location: Portland Or
- MTFCA Number: 52564
- Board Member Since: 1999
Using a 4-1 steering gear box in place of 5-1
I have been looking for the longer slot (26/27) 5-1 gear box to fix a guys column. I have two of the shorter slot 4-1 boxes. How much turning radius would I loose if I used one of them using 21 inch wheels?
I know the voices aren't real but damn they have some good ideas!
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
-
- Posts: 663
- Joined: Thu Jan 03, 2019 3:00 pm
- First Name: Keith
- Last Name: Gumbinger
- * REQUIRED* Type and Year of Model Ts owned: '14 Touring, '26 RPU, '27 Fordor, '27 Touring
- Location: Kenosha, WI
- MTFCA Number: 4661
- MTFCA Life Member: YES
- MTFCI Number: 6866
- Board Member Since: 1999
Re: Using a 4-1 sterring gear box in place of 5-1
Mark, Just a hunch, but could you simply have the slot in one of the gear boxes machined longer?
Just a thought.....
Keith
Just a thought.....
Keith
'14 Touring, '26 Roadster Pickup, '27 Fordor, '27 Touring
Motto: It's hard to build a garage that's tooooo big!
Motto: It's hard to build a garage that's tooooo big!
-
Topic author - Posts: 4967
- Joined: Sat Jan 05, 2019 1:57 pm
- First Name: Mark
- Last Name: Gregush
- * REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
- Location: Portland Or
- MTFCA Number: 52564
- Board Member Since: 1999
Re: Using a 4-1 sterring gear box in place of 5-1
Keith;
I thought about that but can see several issues, nothing to compare to to get proper length and farm out cost. If the slot gets too long you will still end up with pitman arm going over center. I think this might be part of the problem on the box that needs to be replaced, got one side a bit too long when I cleaned the slot up. I don't have the car here and customer is aware of the the issue in case he drives it. I need to have the box on hand to do the swap over as fast as I can after the column gets pulled.
I thought about that but can see several issues, nothing to compare to to get proper length and farm out cost. If the slot gets too long you will still end up with pitman arm going over center. I think this might be part of the problem on the box that needs to be replaced, got one side a bit too long when I cleaned the slot up. I don't have the car here and customer is aware of the the issue in case he drives it. I need to have the box on hand to do the swap over as fast as I can after the column gets pulled.
I know the voices aren't real but damn they have some good ideas!
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
-
- Posts: 1015
- Joined: Sun Jan 06, 2019 10:45 am
- First Name: David
- Last Name: Stroud
- * REQUIRED* Type and Year of Model Ts owned: 1925 Coupe
- Location: Mound City, MO 64470
- Board Member Since: 2011
Re: Using a 4-1 sterring gear box in place of 5-1
Mark, I've switched out two 4to1 sets for 5to1 sets, one on the '23TT that Dallas now has, and the other on our '25 coupe, keeping the original 4to1 gearcases. The only difference that I noticed was that they both steered noticeably easier. That being said, I didn't take any before and after measurements either. Dave
1925 mostly original coupe.
-
- Posts: 1015
- Joined: Sun Jan 06, 2019 10:45 am
- First Name: David
- Last Name: Stroud
- * REQUIRED* Type and Year of Model Ts owned: 1925 Coupe
- Location: Mound City, MO 64470
- Board Member Since: 2011
Re: Using a 4-1 sterring gear box in place of 5-1
I also made new pins for the gears out of drill rod .001 or .002 over size also. That made them fit nice and snug in the shaft holes and took up just a bit of play in the gear holes. It really tightened things up. Dave
1925 mostly original coupe.
-
Topic author - Posts: 4967
- Joined: Sat Jan 05, 2019 1:57 pm
- First Name: Mark
- Last Name: Gregush
- * REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
- Location: Portland Or
- MTFCA Number: 52564
- Board Member Since: 1999
Re: Using a 4-1 sterring gear box in place of 5-1
David did you get the two emails I sent the other day? The second one because I forgot the link in the first.
Mark
Mark
I know the voices aren't real but damn they have some good ideas!
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
-
- Posts: 72
- Joined: Mon Jan 07, 2019 9:45 pm
- First Name: Ted
- Last Name: Dumas
- * REQUIRED* Type and Year of Model Ts owned: 1927 Coupe, 1924 Touring
- Location: Dallas, TX
- MTFCI Number: 20999
Re: Using a 4-1 sterring gear box in place of 5-1
Ask the forum for dimensions on the slot. Someone will have them. Then get the shaft slot milled as was suggested.
-
- Posts: 3675
- Joined: Sun Jan 06, 2019 3:13 pm
- First Name: Wayne
- Last Name: Sheldon
- * REQUIRED* Type and Year of Model Ts owned: 1915 Runabout 1913 Speedster
- Location: Grass Valley California, USA
- Board Member Since: 2005
Re: Using a 4-1 sterring gear box in place of 5-1
I have a simple question. Something I have wondered about for many years. The 4 to 1 or 5 to 1 is the ratio between the steering shaft and the steering wheel. That ratio changes the amount of force required, and amount of turn of the steering wheel needed to make a turn of any given degrees. Since the amount the steering shaft turns relative to the degrees of turning radius does not change, why did they make the slot longer for the 5 to 1 gear cases?
One could think the lowering of the steering column for some of the '26/'27 models would make a difference. But the fact is that difference is negligible, if there is any at all.
Did they find the earlier slot was overly restricting the turning radius? Did they make this difference to identify the 5 to 1 gear cases? That doesn't really make sense. Allowing it to go farther could allow locking on center extreme and basically negate the whole purpose of the slot.
I have never heard of the shorter 4 to 1 slot restricting turning radius enough to cause problems. I can't see why using a 4 to 1 shorter slot case would make much difference.
One could think the lowering of the steering column for some of the '26/'27 models would make a difference. But the fact is that difference is negligible, if there is any at all.
Did they find the earlier slot was overly restricting the turning radius? Did they make this difference to identify the 5 to 1 gear cases? That doesn't really make sense. Allowing it to go farther could allow locking on center extreme and basically negate the whole purpose of the slot.
I have never heard of the shorter 4 to 1 slot restricting turning radius enough to cause problems. I can't see why using a 4 to 1 shorter slot case would make much difference.
-
- Posts: 1112
- Joined: Mon Jan 07, 2019 8:01 am
- First Name: Mark
- Last Name: Nunn
- * REQUIRED* Type and Year of Model Ts owned: 1926 Runabout
- Location: Bennington, NE
- MTFCA Number: 50321
- Board Member Since: 2017
Re: Using a 4-1 sterring gear box in place of 5-1
Wayne, both the 4:1 and 5:1 have 36 teeth so the only real difference is the slot length. Slot width did change, however, probably to accommodate manufacturing tolerances. This is from the encyclopedia.
02-23-22 Changed angle between centerline of case and the center of 13/64” radius at ends of slot for stop pin from 45 degrees to 51 degrees.
05-27-24 Changed angle between centerline and ends of stop slot from 51 degrees to 60 degrees.
09-27-24 Changed angle between centerline and right hand end of slot from 60 degrees to 65 degrees. Specified for 1925.
10-07-25 Changed angle between centerline and ends of stop slot from 60 to 62 degrees on left side and 55 to 67 degrees on right side.
I took a 4:1 gear case that I got from Dave Stroud and milled it to match the last angle change before putting it in my car. I did not do the research but the slot angle changes may have coincided with changes in pitman arm length.
02-23-22 Changed angle between centerline of case and the center of 13/64” radius at ends of slot for stop pin from 45 degrees to 51 degrees.
05-27-24 Changed angle between centerline and ends of stop slot from 51 degrees to 60 degrees.
09-27-24 Changed angle between centerline and right hand end of slot from 60 degrees to 65 degrees. Specified for 1925.
10-07-25 Changed angle between centerline and ends of stop slot from 60 to 62 degrees on left side and 55 to 67 degrees on right side.
I took a 4:1 gear case that I got from Dave Stroud and milled it to match the last angle change before putting it in my car. I did not do the research but the slot angle changes may have coincided with changes in pitman arm length.
-
Topic author - Posts: 4967
- Joined: Sat Jan 05, 2019 1:57 pm
- First Name: Mark
- Last Name: Gregush
- * REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
- Location: Portland Or
- MTFCA Number: 52564
- Board Member Since: 1999
Re: Using a 4-1 sterring gear box in place of 5-1
Mark thanks for that bit of information. Guess I will give hogging out the slot a try. Now all I have to do is find my center build a jig and hope my Craftsman is up to the task.
I know the voices aren't real but damn they have some good ideas!
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
-
- Posts: 1186
- Joined: Mon Jan 07, 2019 10:27 am
- First Name: John
- Last Name: Codman
- * REQUIRED* Type and Year of Model Ts owned: 1927 Youring
- Location: Naples, FL 34120
Re: Using a 4-1 sterring gear box in place of 5-1
Assuming that the 5:1 set is on an "improved car," what will happen is that with the 4:1 gears, the thing will steer hard as Hades. Remember that it has the low-pressure big tires. I'd think long and hard about doing that swap. Ford changed to 5:1 gears for a reason.
-
- Posts: 1112
- Joined: Mon Jan 07, 2019 8:01 am
- First Name: Mark
- Last Name: Nunn
- * REQUIRED* Type and Year of Model Ts owned: 1926 Runabout
- Location: Bennington, NE
- MTFCA Number: 50321
- Board Member Since: 2017
Re: Using a 4-1 sterring gear box in place of 5-1
Correct. He needs to swap the 4:1 steering shaft for a 5:1 shaft and use 5:1 gears. Pin spacing on the two steering shafts are different. That may be why slots were made wider to accommodate different pin spacing. After I assembled my converted gear case I had to trim two spots in the slot with a dremel tool to clear the pin.John Codman wrote: ↑Wed Jun 26, 2019 11:52 amAssuming that the 5:1 set is on an "improved car," what will happen is that with the 4:1 gears, the thing will steer hard as Hades. Remember that it has the low-pressure big tires. I'd think long and hard about doing that swap. Ford changed to 5:1 gears for a reason.
-
- Posts: 3326
- Joined: Sun Jan 06, 2019 10:56 am
- First Name: Dan
- Last Name: Treace
- * REQUIRED* Type and Year of Model Ts owned: '23 cutoff, '25 touring, '27 touring
- Location: North Central FL
- MTFCA Number: 4838
- MTFCI Number: 115
- Board Member Since: 2000
- Contact:
Re: Using a 4-1 sterring gear box in place of 5-1
That is likely the engineering change, the wider pinion posts on the 5:1 ratio steering post shaft.
Here are the two cases, on right is the 4:1, on the left 5:1 for the balloon tires, note the longer groove.
Here are the two cases, on right is the 4:1, on the left 5:1 for the balloon tires, note the longer groove.
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
-
- Posts: 583
- Joined: Thu Jan 10, 2019 11:23 am
- First Name: Bruce
- Last Name: Compton
- * REQUIRED* Type and Year of Model Ts owned: 1921 Coupe, 1925 Coupe
- Location: Kemptville
Re: Using a 4-1 sterring gear box in place of 5-1
To me, Wayne Sheldon's comments sure made sense. The main shaft only rotates so many degrees no matter what ratio is driving it. I don't know why they made the groove any longer, but do know that it had to be wider as the distance from the center of the shaft to the center of the gear pins increased with the 5:1 setup. I've converted 6 Model T's from 4:1 to 5:1 and never had a problem and did not notice a change in turning radius but did notice the ratio change providing more control in actually steering the car(s) . For my '25 Coupe, I found a short pitman arm ( almost 1" shorter ) which also helped although I had to fabricate a blocking plate to prevent the system from going over center.
-
Topic author - Posts: 4967
- Joined: Sat Jan 05, 2019 1:57 pm
- First Name: Mark
- Last Name: Gregush
- * REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
- Location: Portland Or
- MTFCA Number: 52564
- Board Member Since: 1999
Re: Using a 4-1 sterring gear box in place of 5-1
Bruce;
You said something about blocking plate. Do you have any photos of what you did, was unsure how to approach it? I was thinking along the lines of a larger spindle arm nut that would stop the spindle from going past a point when turning.
You said something about blocking plate. Do you have any photos of what you did, was unsure how to approach it? I was thinking along the lines of a larger spindle arm nut that would stop the spindle from going past a point when turning.
I know the voices aren't real but damn they have some good ideas!
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
-
- Posts: 583
- Joined: Thu Jan 10, 2019 11:23 am
- First Name: Bruce
- Last Name: Compton
- * REQUIRED* Type and Year of Model Ts owned: 1921 Coupe, 1925 Coupe
- Location: Kemptville
Re: Using a 4-1 steering gear box in place of 5-1
Mark : After installing the 1" shorter pitman arm, my car's steering would go over center only on sharp right turns so I bolted a 1/4" thick small plate (maybe 3" X 5") to the left front frame rail that stopped the pitman arm from going any farther and just before it would go over center. With the 5:1 ratio, a 17" wheel and the short pitman arm the car steers like a modern car with "real " steering instead of the stock, almost direct "go-cart" steering that most model pre '25 T cars have.
-
Topic author - Posts: 4967
- Joined: Sat Jan 05, 2019 1:57 pm
- First Name: Mark
- Last Name: Gregush
- * REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1920 Dodge touring, 1948 F2 Ford flat head 6 pickup 3 speed
- Location: Portland Or
- MTFCA Number: 52564
- Board Member Since: 1999
Re: Using a 4-1 steering gear box in place of 5-1
This one is going over on hard left, so I would have to mount a stop on the pan rail.
I know the voices aren't real but damn they have some good ideas!
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
1925 Cut down pickup
1920 Dodge touring
1948 Ford F2 pickup
-
- Posts: 583
- Joined: Thu Jan 10, 2019 11:23 am
- First Name: Bruce
- Last Name: Compton
- * REQUIRED* Type and Year of Model Ts owned: 1921 Coupe, 1925 Coupe
- Location: Kemptville
Re: Using a 4-1 steering gear box in place of 5-1
Mark : Whether it goes over center left or right depends on the length of the tie rod. There are several different lengths you could try and if you pick the right one it may not go over center in either direction.