Will this work on my acetylene tank?

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
Marty Bufalini
Posts: 185
Joined: Mon Jan 07, 2019 9:17 pm
First Name: Marty
Last Name: Bufalini
* REQUIRED* Type and Year of Model Ts owned: 1914 Touring
Location: Michigan

Will this work on my acetylene tank?

Post by Marty Bufalini » Sun Oct 27, 2019 10:19 am

All I want to do is regulate the amount of gas going to the headlights. Right now, I have no gauge at all and just crack the valve until I think I have enough going to the lights, then light them and regulate them. I want something that's vintage looking.

That's been to chancy for me.

Thanks,

Marty
s-l1600.jpg


otrcman
Posts: 364
Joined: Sun Jan 06, 2019 2:25 pm
First Name: Dick
Last Name: Fischer
* REQUIRED* Type and Year of Model Ts owned: 1912 Touring
Location: Arroyo Grande, CA

Re: Will this work on my acetylene tank?

Post by otrcman » Sun Oct 27, 2019 10:45 am

Marty, That won't actually regulate the gas pressure; it'll just tell you how much pressure you have set. And it will only read correctly with all the the gas valves flowing at the same time.

An acetylene regulator on a welding tank typically has two gages -- a high pressure gage and a low pressure. The high pressure gage reads the internal pressure in the tank (to tell you how much gas remains in the tank) and the low pressure gage tells you how much pressure is set to flow out of the regulator and down the hose. Be careful not to put your low pressure gage at the outlet of the tank, as tank pressure will be 'way too high for that gage.

A true regulator tries to keep the pressure constant regardless of how many outlets are opened downstream of the regulator. You may be able to come up with a small gas regulator and install your old looking gage on the modern regulator.


Jerry VanOoteghem
Posts: 2952
Joined: Sun Jan 06, 2019 4:06 pm
First Name: Jerry
Last Name: Van
Location: S.E. Michigan
MTFCA Number: 24868

Re: Will this work on my acetylene tank?

Post by Jerry VanOoteghem » Sun Oct 27, 2019 2:41 pm

That won't do what you want Marty.

The pressure to your lights should be nearly zero, but not quite. This gauge's needle will not even move off the peg at those low pressures. You don't need a gauge, what you need is a regulator. There were regulators made in the Model T era, and those that you can buy today at welding shops. Either way, do NOT use anything that was not originally designed and intended fore use with acetylene. This is no place to retrofit or innovate.


Scott_Conger
Posts: 6431
Joined: Sun Jan 06, 2019 11:18 am
First Name: Scott
Last Name: Conger
* REQUIRED* Type and Year of Model Ts owned: '13, '15, '19, '23
Location: Clark, WY
Board Member Since: 2005

Re: Will this work on my acetylene tank?

Post by Scott_Conger » Sun Oct 27, 2019 2:51 pm

Acetylene is funny stuff and there are materials/devices you do NOT want mixed in with it.

Jerry has given excellent warning/advice

be careful
Scott Conger

Tyranny under the guise of law is still Tyranny

NH Full Flow Float Valves
Obsolete carburetor parts manufactured


Jerry VanOoteghem
Posts: 2952
Joined: Sun Jan 06, 2019 4:06 pm
First Name: Jerry
Last Name: Van
Location: S.E. Michigan
MTFCA Number: 24868

Re: Will this work on my acetylene tank?

Post by Jerry VanOoteghem » Sun Oct 27, 2019 2:57 pm

Something like this may work for you: https://www.ebay.com/itm/Victor-Acetyle ... SwyXNZ7SXV

This is pretty close to what I use. This one is a little big/bulky though: https://www.ebay.com/itm/ESAB-Purox-R-2 ... SwKQ9aTCA9

Another possibility: https://www.ebay.com/itm/Uniweld-RB-Ace ... Sw~oFXMj60

Or: https://www.ebay.com/itm/PREST-O-LITE-A ... SwKs1dbUml I think this one may be your best bet.


Notice the regulator on this tank. It's an old fashioned Prestolite style. Don't know if it's adjustable or not. https://www.ebay.com/itm/Vintage-Prest- ... 8045!US!-1


Yup, the new ones are ugly on a T, but at least the one I use, works great, (on my Overland).


John kuehn
Posts: 3907
Joined: Sun Jan 06, 2019 8:00 pm
First Name: John
Last Name: Kuehn
* REQUIRED* Type and Year of Model Ts owned: 19 Roadster, 21 Touring, 24 Coupe
Location: Texas
MTFCA Number: 28924

Re: Will this work on my acetylene tank?

Post by John kuehn » Sun Oct 27, 2019 8:35 pm

So what was the way to adjust the pressure to the lights. Just using the off/on valve on the tank to regulate it? Is that the way Ford recommended to owners how to do it?
Just wondering since I have black era T’s and not brass.


Original Smith
Posts: 3284
Joined: Tue Jan 08, 2019 10:43 am
First Name: Larry
Last Name: Smith
* REQUIRED* Type and Year of Model Ts owned: 13 Touring, 13 Roadster, 17 Coupelet, 25 Roadster P/U
Location: Lomita, California
MTFCA Number: 121
MTFCA Life Member: YES
MTFCI Number: 16310

Re: Will this work on my acetylene tank?

Post by Original Smith » Sun Oct 27, 2019 9:30 pm

I don't think there is any pressure off a carbide generator.


Allan
Posts: 5205
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Will this work on my acetylene tank?

Post by Allan » Mon Oct 28, 2019 12:24 am

I am lucky with my chocolate van. There is a small, modern cylinder and an old, two gauge regulator on top. With this set-up, the headlights can be adjusted way down so you have parking lights!

Allan from down under.

User avatar

KWTownsend
Posts: 1122
Joined: Mon Jan 07, 2019 6:51 pm
First Name: Keith
Last Name: Townsend
* REQUIRED* Type and Year of Model Ts owned: late 1911 touring, 1915 runabout, 1919 touring, brass speedster
Location: Gresham, Orygun
MTFCA Number: 14778
MTFCA Life Member: YES
MTFCI Number: 16305
Board Member Since: 1999

Re: Will this work on my acetylene tank?

Post by KWTownsend » Mon Oct 28, 2019 1:44 am

Marty-
When I was experimenting with the MC tank I used a small regulator (like the second one Jerry showed) but the handle unscrewed it self and fell off!

I like the fourth one he shows.

However, there is no need for a regulator. They did NOT come with a regulator. I just crack the valve open. It takes 2 lbs pressure, about 1/8 of a turn of the valve.

Keith

: ^ )


Topic author
Marty Bufalini
Posts: 185
Joined: Mon Jan 07, 2019 9:17 pm
First Name: Marty
Last Name: Bufalini
* REQUIRED* Type and Year of Model Ts owned: 1914 Touring
Location: Michigan

Re: Will this work on my acetylene tank?

Post by Marty Bufalini » Mon Oct 28, 2019 6:33 pm

Thank you all. Great advice.

I was looking for something that looked more period so I guess I'll just stick with the "just crack the valve" method.

I've had this full tank for a couple of years and, although I don't use the lights that often, I do use them. I guess I'll know when it's empty when I no longer get any gas out of it.

Thanks again.

Marty

User avatar

Fordwright
Posts: 245
Joined: Tue Oct 29, 2019 4:14 pm
First Name: Greg
Last Name: Popove
Location: Olds AB

Re: Will this work on my acetylene tank?

Post by Fordwright » Tue Oct 29, 2019 4:43 pm

John kuehn wrote:
Sun Oct 27, 2019 8:35 pm
So what was the way to adjust the pressure to the lights. Just using the off/on valve on the tank to regulate it? Is that the way Ford recommended to owners how to do it?
Just wondering since I have black era T’s and not brass.
No acetylene tank at all. A needle valve regulated how much water dripped onto chunks of calcium carbide. More water = more gas.


John kuehn
Posts: 3907
Joined: Sun Jan 06, 2019 8:00 pm
First Name: John
Last Name: Kuehn
* REQUIRED* Type and Year of Model Ts owned: 19 Roadster, 21 Touring, 24 Coupe
Location: Texas
MTFCA Number: 28924

Re: Will this work on my acetylene tank?

Post by John kuehn » Tue Oct 29, 2019 5:28 pm

Thanks for answering the question.

Post Reply Previous topicNext topic