Page 1 of 1

Stevens/Walden tool catalogs update ...

Posted: Mon Oct 12, 2020 11:42 pm
by dobro1956
Update, 10/29/2020, I am in the process of ordering the second run of catalogs, hope to have them soon. Will post a new ad when they arrive ...

Everyone who was interested in a catalog, please check your e-mails. I have sent out e-mails to the first 25 folks that were interested in the catalogs. There were two more interested in catalogs than I have copies to send at this time. . After I get this run taken care of Ill be doing at least one more run of catalogs. Please bear with me, I'm old, slow, and walk with a limp. :) dmdeaton and Dan B you are the first two in line for the second run.... Ill order, and then post the second run for sale after I have all these mailed ... Its just too complicated for my feeble mind to handle more than 25 at a time .... :) Thanks again for the interest in my projects ....

Here is a link to the first post about the catalogs if you have forgotten by now what I had reprinted.


https://mtfca.com/phpBB3/viewtopic.php?t=15634

Re: Stevens/Walden tool catalogs update ...

Posted: Tue Oct 13, 2020 11:07 am
by FordFool
Donnie. Still interested. Keep me posted. Don

Re: Stevens/Walden tool catalogs update ...

Posted: Tue Oct 13, 2020 11:38 am
by Lonnie Doan
I'd take one if any are left. No hurry. Thanks.

Re: Stevens/Walden tool catalogs update ...

Posted: Tue Oct 13, 2020 11:51 am
by George Hand
Donnie, I put check in the mail. Thanks George

Re: Stevens/Walden tool catalogs update ...

Posted: Tue Oct 13, 2020 12:35 pm
by FordFool
Donnie I’ll get a check in the mail ASAP. Thanks. Don

Re: Stevens/Walden tool catalogs update ...

Posted: Tue Oct 13, 2020 12:58 pm
by Bill Anziani
Sent payment this morning via pay pal

Re: Stevens/Walden tool catalogs update ...

Posted: Tue Oct 13, 2020 10:31 pm
by Dan B
dobro1956 wrote:
Mon Oct 12, 2020 11:42 pm
Everyone who was interested in a catalog, please check your e-mails. I have sent out e-mails to the first 25 folks that were interested in the catalogs. There were two more interested in catalogs than I have copies to send at this time. . After I get this run taken care of Ill be doing at least one more run of catalogs. Please bear with me, I'm old, slow, and walk with a limp. :) dmdeaton and Dan B you are the first two in line for the second run.... Ill order, and then post the second run for sale after I have all these mailed ... Its just too complicated for my feeble mind to handle more than 25 at a time .... :) Thanks again for the interest in my projects ....

Here is a link to the first post about the catalogs if you have forgotten by now what I had reprinted.


https://mtfca.com/phpBB3/viewtopic.php?t=15634
Sounds good Donnie, keep me posted. Thanks!!

Re: Stevens/Walden tool catalogs update ...

Posted: Wed Oct 14, 2020 1:07 pm
by GG Gregory
I’d love a copy of your next run.

Re: Stevens/Walden tool catalogs update ...

Posted: Sat Oct 17, 2020 3:25 pm
by sweet23
Received mine today. Very nice. Great job on them Donnie.

Re: Stevens/Walden tool catalogs update ...

Posted: Sat Oct 17, 2020 4:52 pm
by CDooREDW
Donnie, pls put me down for a copy of your next printing. No hurry, sir. Thank you, Ron

Re: Stevens/Walden tool catalogs update ...

Posted: Sat Oct 17, 2020 11:05 pm
by pre15dale
Donnie, I was #21 or 22 on the original post. I have not receive an s mail. Please refresh my memory of the cost and where to send it. Dale

Re: Stevens/Walden tool catalogs update ...

Posted: Sun Oct 18, 2020 3:08 am
by Fordnut
Donnie, I would love to be on the list for the next run. Richard

Re: Stevens/Walden tool catalogs update ...

Posted: Sun Oct 18, 2020 11:25 am
by dobro1956
We went on a tour for the last few days. We wrecked the car when I lost control of car when Warford went into neutral. It rolled backward down a steep embankment and flipped over at the bottom. We are not hurt but I have been distracted for several days. Ill post about the wreck later. Please check your e-mails and spam folders. I sent e-mails out to everyone that was in the first 25 names. Ill start checking my list to see who has not responded. I have mailed 5 catalogs to the 5 people who paid with pay pal. I just received another pay pal payment for #6. I also have 5 contacts from folks mailing a check or money order. Just started receiving some of the checks, So Ill be mailing a few more catalogs Monday. So that leaves me with 14 folks I need to re-contact or maybe they will find the original e-mail. Please bear with me,
Thanks, Donnie Brown

Re: Stevens/Walden tool catalogs update ...please read Sunday Oct 18th post

Posted: Sun Oct 25, 2020 6:16 pm
by George Hand
Donnie, I received my catalog this week, looks great, home you made it home from your tour without any more problems. George