Ball bearing Rear end thrust FS New Price

Post parts wanted or for sale here

Topic author
Dan Hatch
Posts: 4110
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Ball bearing Rear end thrust FS New Price

Post by Dan Hatch » Sat Jul 02, 2022 3:58 pm

Here is a set of aftermarket Ball Bearing Thrust bearings. They maybe NOS no sure. There 2 of the ball bearings plate and 7 of the race plates. Ran them through the vibration tumbler to remove the surface rust. Can they be used? That will be up to new owner. $20 + shipping. Email me at address in pictures. Thanks Dan
380B9ABB-797A-4234-9C2A-D80A84FB3ED5.jpeg
F6FAC53B-719C-4CCC-AD2F-FB3B7830DAD5.jpeg
256BDB65-0AAB-4B3A-B502-6B75BEA310C1.jpeg
256BDB65-0AAB-4B3A-B502-6B75BEA310C1.jpeg (34.02 KiB) Viewed 1296 times
Last edited by Dan Hatch on Fri Jul 29, 2022 9:42 am, edited 1 time in total.


Allan
Posts: 5201
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Ball bearing Rear end thrust FS

Post by Allan » Sat Jul 02, 2022 10:50 pm

Dan, are the 7 solid plates different thicknesses? That would allow some adjustment within the pumpkin when assembling the diff centre. Just curious.
Allan from down under.


speedytinc
Posts: 3839
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
MTFCA Number: 14383
Board Member Since: 2020

Re: Ball bearing Rear end thrust FS

Post by speedytinc » Sat Jul 02, 2022 11:11 pm

Allan wrote:
Sat Jul 02, 2022 10:50 pm
Dan, are the 7 solid plates different thicknesses? That would allow some adjustment within the pumpkin when assembling the diff centre. Just curious.
Allan from down under.
They mount on the stock thrust washer pins. You can add shims to tighten the gear clearance.
If too tight, you get creative. remove material from the carrier or surface grind the race plates.


Topic author
Dan Hatch
Posts: 4110
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Re: Ball bearing Rear end thrust FS

Post by Dan Hatch » Sun Jul 03, 2022 4:51 am

Do not know, have not measured them. Here is copy of ad for them. Thanks to Dan T for posting it in other forum.
9B781955-6E83-4AD0-9C67-87CB92DFDD1D.jpeg
9B781955-6E83-4AD0-9C67-87CB92DFDD1D.jpeg (67.25 KiB) Viewed 1154 times


Topic author
Dan Hatch
Posts: 4110
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Re: Ball bearing Rear end thrust FS

Post by Dan Hatch » Sun Jul 10, 2022 3:41 pm

No interest in these? Off to china I guess.


Topic author
Dan Hatch
Posts: 4110
Joined: Tue Jan 08, 2019 7:31 pm
First Name: Dan
Last Name: Hatch
Location: Alabama
MTFCA Number: 49974

Re: Ball bearing Rear end thrust FS

Post by Dan Hatch » Fri Jul 29, 2022 9:42 am

Hate to scrap

Post Reply Previous topicNext topic