Wheel Spindle help!

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
Belliott3
Posts: 333
Joined: Sat Jan 19, 2019 7:44 pm
First Name: Bill
Last Name: Elliott
* REQUIRED* Type and Year of Model Ts owned: 1916 Model T Touring
Location: Michigan
MTFCA Number: 52438
MTFCI Number: 22121
Board Member Since: 2006

Wheel Spindle help!

Post by Belliott3 » Tue Jun 04, 2019 1:17 pm

Once more, I've hit a snag in my restoration attempt on my 1910 T and I need some help. I'm in the process of mounting new tires on my new Stutzman wheels and I'm test fitting the new outer threaded Timken bearings (yes Timken, not ball bearings) on the spindles and the passenger side goes on fine but the drives side binds up about a quarter of the way on. The threads appear to be mostly o.k, but may be a little flat in a few areas. I've cleaned off all gunk and old grease but it still won't thread on. I'm thinking I need to clean up the threads with a thread chaser, but not sure if that's the correct terminology. Anyone know what size chaser I would need?


Les Schubert
Posts: 1311
Joined: Thu Jan 10, 2019 5:47 pm
First Name: Les
Last Name: Schubert
* REQUIRED* Type and Year of Model Ts owned: 27 roadster 13 touring
Location: Calgary

Re: Wheel Spindle help!

Post by Les Schubert » Tue Jun 04, 2019 2:03 pm

“Universal “ thread chasers are available. Check with the local quality tool stores. Snap-on comes to mind


mtntee20
Posts: 527
Joined: Sun Jan 06, 2019 2:51 pm
First Name: Terry & Sharon
Last Name: Miller
* REQUIRED* Type and Year of Model Ts owned: 1920 Center Door, 1920 TTWood cab Farm Truck with cable dump grain bed, 1920 TT C-Cab with express bed, 1927 Wood body Dairy Delivery truck
Location: Westminster, CO
MTFCA Number: 32583
Board Member Since: 2017

Re: Wheel Spindle help!

Post by mtntee20 » Tue Jun 04, 2019 2:10 pm

Bill,

You might consider a thread file. Each one has 8 different thread pitches and there is a file for metric as well. The nice thing about a thread file is; you can start anywhere on the threads and not worry about getting it started exactly right. These have saved my rear end ( not axle ) :lol: a bunch of times. They will work on right OR left hand threads as well.

Good Luck,
Terry

User avatar

Ruxstel24
Posts: 2345
Joined: Sun Jan 06, 2019 11:25 am
First Name: Dave
Last Name: Hanlon
* REQUIRED* Type and Year of Model Ts owned: 24 Touring car
Location: NE Ohio
MTFCA Number: 50191
Board Member Since: 2018

Re: Wheel Spindle help!

Post by Ruxstel24 » Tue Jun 04, 2019 2:13 pm

X2 on a thread file.
If you have the old bearing race, you may be able to use it as a chaser.


Topic author
Belliott3
Posts: 333
Joined: Sat Jan 19, 2019 7:44 pm
First Name: Bill
Last Name: Elliott
* REQUIRED* Type and Year of Model Ts owned: 1916 Model T Touring
Location: Michigan
MTFCA Number: 52438
MTFCI Number: 22121
Board Member Since: 2006

Re: Wheel Spindle help!

Post by Belliott3 » Tue Jun 04, 2019 2:49 pm

Thanks for the two suggestions! Les, do you know what size threads the spindles have? I see the Universal thread chaser is listed for use with 5/32" to 1/2" threads. Terry and Dave; is there a particular size in the thread file or are they basically universal?


R.V.Anderson
Posts: 680
Joined: Tue Jan 08, 2019 6:01 pm
First Name: R.V.
Last Name: Anderson
* REQUIRED* Type and Year of Model Ts owned: 1914, 1920, 1923, 1923
Location: Kennedy, NY

Re: Wheel Spindle help!

Post by R.V.Anderson » Tue Jun 04, 2019 3:39 pm

The thread size is 3/4" x 16.

User avatar

DanTreace
Posts: 3299
Joined: Sun Jan 06, 2019 10:56 am
First Name: Dan
Last Name: Treace
* REQUIRED* Type and Year of Model Ts owned: '23 cutoff, '25 touring, '27 touring
Location: North Central FL
MTFCA Number: 4838
MTFCI Number: 115
Board Member Since: 2000
Contact:

Re: Wheel Spindle help!

Post by DanTreace » Tue Jun 04, 2019 4:24 pm

Remember your spindle threads are left hand and right hand, be sure you know which spindle you are chasing.

The best way is a thread chaser, if the beginning threads on the end of the spindle are good, that lets the chase die turn easy on.
those square thread tools work for flat spots on threads, but I've preferred a good set of thread chasers in the tool box.

Left or right chasers are rather inexpensive. About $3-4 ea.


https://www.mcmaster.com/thread-chasers

3/4"-16 1 1/8" Carbon Steel 2667A438 2.89
Product Detail
Thread Repairing Die, 3/4"-16 Thread Size, 1-1/8" Wrench/Socket Size
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford


Norman Kling
Posts: 4071
Joined: Tue Jan 08, 2019 1:39 pm
First Name: Norman
Last Name: Kling
Location: Alpine California

Re: Wheel Spindle help!

Post by Norman Kling » Tue Jun 04, 2019 4:29 pm

How does the nut fit? If it binds in the same place, your problem is in the spindle threads, but if it doesn't bind, your problem could be in the bearing threads. If that is a new bearing, you can considering sending it back in exchange for another. Otherwise, try to find someone who would have a tap which would fit. If it just binds, you could possibly try some timesaver on the threads and tighten it again, working back and forth till it seats. I would have a problem using a file on the spindle threads unless I could see where it was binding. Usually caused by dropping the part and denting the threads.
Norm

User avatar

tinman080
Posts: 47
Joined: Mon Jan 14, 2019 12:36 am
First Name: gary
Last Name: hammond
* REQUIRED* Type and Year of Model Ts owned: 1926 roadster
Location: forest, va
Board Member Since: 2016

Re: Wheel Spindle help!

Post by tinman080 » Tue Jun 04, 2019 7:48 pm

If you have an extra spindle nut you can cut a couple of thin slots about 1/4'' deep across the back of the nut. Clean any dust and debris from the nut and thread her on with a drop of oil. Works just like a die or thread chaser.
''Just Passin' Thru.....Slowly! :D


Allan
Posts: 5201
Joined: Sun Jan 06, 2019 7:21 pm
First Name: Allan
Last Name: Bennett
* REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
Location: Gawler, Australia

Re: Wheel Spindle help!

Post by Allan » Tue Jun 04, 2019 8:06 pm

Gary has a good idea. I was wondering how to cut grooves across the thread in a hardened old bearing to make a chaser. His nut idea is much more easily achieved.

Allan from down under.


sweet23
Posts: 481
Joined: Sun Jan 06, 2019 1:19 pm
First Name: Darryl
Last Name: Bobzin
* REQUIRED* Type and Year of Model Ts owned: 2, '25 T Runabouts, '14 Touring
Location: Kannapolis,NC
MTFCA Number: 27211
Board Member Since: 2016

Re: Wheel Spindle help!

Post by sweet23 » Tue Jun 04, 2019 9:25 pm

Alan, use a three corner file to cut three grooves in your old bearing. It will make a nice thread chaser. I have also done this with a castle nut to make a chaser.


mtntee20
Posts: 527
Joined: Sun Jan 06, 2019 2:51 pm
First Name: Terry & Sharon
Last Name: Miller
* REQUIRED* Type and Year of Model Ts owned: 1920 Center Door, 1920 TTWood cab Farm Truck with cable dump grain bed, 1920 TT C-Cab with express bed, 1927 Wood body Dairy Delivery truck
Location: Westminster, CO
MTFCA Number: 32583
Board Member Since: 2017

Re: Wheel Spindle help!

Post by mtntee20 » Wed Jun 05, 2019 7:38 am

Bill,

Thread files are universal, left or right hand threads. They will cut anything the same way as a regular file would. Each file has 4 different thread pitches on EACH end for a total of eight per file. You only need one file with the pitch you're looking for. 16 is the pitch I believe. You can look up thread file on the web and find them just about everywhere. This is one time where I will recommend Harbor Garbage. This is an item you will need but not often. Thus, there is no need to buy an expensive set, unless you wanted a high quality set for any future needs.

Good Luck,
Terry


baltrusch
Posts: 49
Joined: Mon Jan 07, 2019 8:58 am
First Name: Kurt
Last Name: Baltrusch
* REQUIRED* Type and Year of Model Ts owned: 1914 speedster, 1918 Touring, 1922 Sedan
Location: Great Falls, MT

Re: Wheel Spindle help!

Post by baltrusch » Wed Jun 05, 2019 9:55 am

I assume that the 1910 is the same as the later Ts, if not, excuse my ignorance! It is good that the right side with the left hand threads went on well as a 3/4x16 left hand die might be hard to find. However, the thread file has always worked for me, and will work on either side. Another trick is to take a nut with the same threads and hacksaw a slot all the way through on one side of the nut, perpendicular to the threads. You can use an old bearing as well, just cut it with a die grinder. Thread this onto the spindle and it will expand over the bad threads. Once all the way on, take a vise grip and clamp it tight across the flats and unscrew it, using lots of oil You may have to go looser on the first attempt, but tighten it more each time.
Attachments
thread chaser.JPG


Topic author
Belliott3
Posts: 333
Joined: Sat Jan 19, 2019 7:44 pm
First Name: Bill
Last Name: Elliott
* REQUIRED* Type and Year of Model Ts owned: 1916 Model T Touring
Location: Michigan
MTFCA Number: 52438
MTFCI Number: 22121
Board Member Since: 2006

Re: Wheel Spindle help!

Post by Belliott3 » Wed Jun 05, 2019 10:11 am

Thank you all for the great ideas; I really do appreciate it! I'll keep you posted.

Post Reply Previous topicNext topic