Search found 488 matches

by John Warren
Sun Dec 15, 2019 11:00 am
Forum: 2019 General Discussion Forum
Topic: modern connecting rods with insert bearings
Replies: 6
Views: 342

Re: modern connecting rods with insert bearings

A lot of Model A guys are going with inserts with no mods to the oil system. Hi mileage is at 60,000+ miles. My race car has all insert bearings, only about 2,000 miles on it now. It is a must to keep clean oil in it!. Model A's have an oil pump, but not a pressured system. It floods the lifter area...
by John Warren
Sun Dec 08, 2019 10:05 am
Forum: 2019 General Discussion Forum
Topic: What are the symptoms of an intake leak?
Replies: 11
Views: 530

Re: What are the symptoms of an intake leak?

It could be a valve seal problem, at higher speed the problem would disappear. I would check out the intake manifold, carb gasket first. One of the old timers here would take a hammer and tap on the intake manifold near the clamp and re-tighten it. With it coughing at an idle means it is lean, but i...
by John Warren
Sun Dec 08, 2019 9:25 am
Forum: 2019 General Discussion Forum
Topic: A new shelter for my Speedster and a little contest...
Replies: 22
Views: 1320

Re: A new shelter for my Speedster and a little contest...

So what's in the jar? Nice Shop, congratulations.
by John Warren
Sun Dec 08, 2019 9:14 am
Forum: 2019 General Discussion Forum
Topic: Interesting clutch on ebay
Replies: 10
Views: 709

Re: Interesting clutch on ebay

I was riding in a 60's car when I was 7 or 8 , not sure what it was , and the driver was showing me how it always coasted when you weren't under power. So coming up to stop sign there was no engine assisted stop. It was an automatic transmission of some sort, and I also remembered that she had to le...
by John Warren
Sun Dec 08, 2019 9:03 am
Forum: 2019 General Discussion Forum
Topic: Valve Springs
Replies: 4
Views: 272

Re: Valve Springs

If you are not running a racing engine of some sort, there is not much of a requirement, so probably safe from any of the vendors.
by John Warren
Sun Dec 08, 2019 9:00 am
Forum: 2019 General Discussion Forum
Topic: Convert my 1921 Kerosene tail light to electric
Replies: 10
Views: 436

Re: Convert my 1921 Kerosene tail light to electric

There are a few guys here that have installed led lights in their side lamps that was circular and had its own battery, I think they were from harbor freight. They didn't have to modify it them at all. It would work well if you are only using it for a tail light.
by John Warren
Sun Dec 08, 2019 8:44 am
Forum: 2019 General Discussion Forum
Topic: Talk about speedsters please
Replies: 18
Views: 835

Re: Talk about speedsters please

IMG_20190712_194007.jpg
IMG_20190712_194007.jpg (107.49 KiB) Viewed 710 times
IMG_20190712_193933.jpg
IMG_20190712_193933.jpg (109.63 KiB) Viewed 710 times
Here is a speedster that Shane Latch is building that looks similar to the Bugatti.
by John Warren
Mon Dec 02, 2019 9:40 pm
Forum: 2019 General Discussion Forum
Topic: Speedster rebuild
Replies: 32
Views: 2095

Re: Speedster rebuild

Peter, Looking great! Also thanks for the additional photos and info on the steering gear.
by John Warren
Mon Dec 02, 2019 9:11 pm
Forum: 2019 General Discussion Forum
Topic: Model T road trip in 1924
Replies: 8
Views: 593

Re: Model T road trip in 1924

Very Nice Thanks for sharing.
by John Warren
Thu Nov 28, 2019 10:23 am
Forum: 2019 General Discussion Forum
Topic: Model T Special build.
Replies: 139
Views: 10533

Re: Model T Special build.

WOW Shane, You have been making progress. The crumb cruncher is a special touch. I am sure, like me, you have done many hours of barn flying. Thanks for sharing and Happy Thanks Giving.
by John Warren
Sat Nov 16, 2019 6:59 pm
Forum: 2019 General Discussion Forum
Topic: diy valve spring compressor?
Replies: 8
Views: 574

Re: diy valve spring compressor?

I’m with Scott on the manifolds and I like Steve’s first spring compressor
by John Warren
Sun Nov 10, 2019 12:58 pm
Forum: 2019 General Discussion Forum
Topic: Speedster rebuild
Replies: 32
Views: 2095

Re: Speedster rebuild

Peter, Is there any chance of getting better photos of the steering box, and any other info you may have on it? I purchased the one on ebay and it is missing the top and the input gear. Thanks in advance.
by John Warren
Sun Nov 10, 2019 12:41 pm
Forum: 2019 General Discussion Forum
Topic: Any news about Larry Sigworth ?
Replies: 11
Views: 1271

Re: Any news about Larry Sigworth ?

I did get to meet Larry at the speedster reunion in Lincoln this year. Great guy that will be missed. Prayers and condolences to his family and friends.
by John Warren
Fri Nov 08, 2019 1:35 am
Forum: 2019 General Discussion Forum
Topic: Installing a 1926 Radiator.
Replies: 11
Views: 570

Re: Installing a 1926 Radiator.

510783.jpg
Thanks to Martyn Vowell
by John Warren
Tue Nov 05, 2019 8:04 pm
Forum: 2019 General Discussion Forum
Topic: Ron Carey Dies in London to Brighton
Replies: 14
Views: 1765

Re: Ron Carey Dies in London to Brighton

A sad day, Condolences to family and friends.
by John Warren
Sat Nov 02, 2019 9:12 pm
Forum: 2019 General Discussion Forum
Topic: Adjustable lifters with stainless steel valves...
Replies: 22
Views: 840

Re: Adjustable lifters with stainless steel valves...

Well as long as we are talking about valves. These came with some model t parts. 🤷‍♂️ 😁
FC89E22B-1F4D-4EFD-AE93-86F4A508A43A.jpeg
by John Warren
Fri Nov 01, 2019 9:01 am
Forum: 2019 General Discussion Forum
Topic: REVERSE FLOW ENGINE
Replies: 27
Views: 2612

Re: REVERSE FLOW ENGINE

It should help rpms. I have a reverse ground cam and would like to try it some day.
by John Warren
Wed Oct 30, 2019 11:11 am
Forum: 2019 General Discussion Forum
Topic: Model T Special build.
Replies: 139
Views: 10533

Re: Model T Special build.

Beautiful baby girl. Yes you need to let her absorb you. Looks like a very nice engine set up. Is it in good shape? Looking forward to updates. Thanks
by John Warren
Sun Oct 27, 2019 11:18 am
Forum: 2019 General Discussion Forum
Topic: Model T Special build.
Replies: 139
Views: 10533

Re: Model T Special build.

Hi Shane, How are thing going? Making any new progress? Eric's and Roberts new car sure looks great!
by John Warren
Sun Oct 27, 2019 10:33 am
Forum: 2019 General Discussion Forum
Topic: Ford stamping on front cross member
Replies: 9
Views: 473

Re: Ford stamping on front cross member

Yes that is my speedster/race car. I happened to have a small piece of a cross member that happened to have that stamp on it and I needed something to make the u-bolts to fit correctly, and yes the frame that it is atatched to has the stamp also. Not in the center, they were both just like yours.
by John Warren
Sun Oct 27, 2019 10:30 am
Forum: 2019 General Discussion Forum
Topic: Leather rear axle seals
Replies: 11
Views: 542

Re: Leather rear axle seals

Hi Guys, I have thought about this some for a while. I have been installing a bearing/seal setup on most of my model T's. It works well with a modern bearing and seal. I would also like to see a free floating seal that could be used with stock bearings. The modern seals for this don't float and can'...
by John Warren
Sat Oct 26, 2019 9:57 am
Forum: 2019 General Discussion Forum
Topic: Pen and ink and sketches.
Replies: 44
Views: 2519

Re: Pen and ink and sketches.

Great stuff!!! thanks
by John Warren
Wed Oct 23, 2019 8:52 pm
Forum: 2019 General Discussion Forum
Topic: Model T Artwork
Replies: 4
Views: 358

Re: Model T Artwork

👍😁
by John Warren
Tue Oct 22, 2019 8:34 pm
Forum: 2019 General Discussion Forum
Topic: Gas up the Ford
Replies: 4
Views: 490

Re: Gas up the Ford

Love it, thanks.
by John Warren
Tue Oct 22, 2019 8:52 am
Forum: 2019 General Discussion Forum
Topic: Buying on Craig's List
Replies: 69
Views: 3461

Re: Buying on Craig's List

Probably not in neutral. Easy mistake.
by John Warren
Mon Oct 21, 2019 8:09 pm
Forum: 2019 General Discussion Forum
Topic: Dodged a bullet yesterday.
Replies: 10
Views: 850

Re: Dodged a bullet yesterday.

A couple of photos of findings. The bolts were were sorta still in place along with the spring. The cover was keeping it sorta together.
C0895495-2CD8-4BE1-A477-FA25022169C5.jpeg
[/size]
by John Warren
Sun Oct 20, 2019 10:17 pm
Forum: OT - Off topic
Topic: the model A and church.
Replies: 9
Views: 775

Re: the model A and church.

Been there done that. A dead battery just never happens at a good time. If it happens at home, would be the only exception. The hand crank can definitely bail us out. I have had to push start the race car more than once. At times I wish I could have hand cranked it. In my case it is not an option. ...
by John Warren
Sun Oct 20, 2019 9:59 pm
Forum: 2019 General Discussion Forum
Topic: Dodged a bullet yesterday.
Replies: 10
Views: 850

Re: Dodged a bullet yesterday.

A little luck or devine intervention, I’ll take it! Thanks Hank.
by John Warren
Sun Oct 20, 2019 7:37 pm
Forum: 2019 General Discussion Forum
Topic: Dodged a bullet yesterday.
Replies: 10
Views: 850

Dodged a bullet yesterday.

Yesterday, I dusted off my 25 roadster pickup and took it on our clubs breakfast run. Some 25 miles later after breakfast, I go to start it with the crank and it is being unusually stubborn. I go ahead and use the starter but it sounds different when cranking. After it starts it is running great ju...
by John Warren
Sun Oct 20, 2019 11:11 am
Forum: 2019 General Discussion Forum
Topic: Font size.
Replies: 7
Views: 288

Re: Font size.

And Thanks Dave
by John Warren
Sun Oct 20, 2019 11:03 am
Forum: 2019 General Discussion Forum
Topic: Font size.
Replies: 7
Views: 288

Re: Font size.

Ok let’s try this. It is the large size. Thanks Now the huge size. Thanks Steve
I mean Thanks Steve
by John Warren
Sun Oct 20, 2019 10:51 am
Forum: 2019 General Discussion Forum
Topic: High Gear
Replies: 8
Views: 538

Re: High Gear

Like Scott said. If it has modern clutch discs in it, it will chatter unless you rpms are matched.
by John Warren
Sun Oct 20, 2019 10:26 am
Forum: 2019 General Discussion Forum
Topic: Font size.
Replies: 7
Views: 288

Re: Font size.

Not being able to change the font size maybe a iPhone thing. Steve what say you?
by John Warren
Sun Oct 20, 2019 10:17 am
Forum: 2019 General Discussion Forum
Topic: Font size.
Replies: 7
Views: 288

Re: Font size.

When I poke the size button it brings up different sizes. I move it from normal to large and it is not changing anything.
by John Warren
Sun Oct 20, 2019 10:13 am
Forum: 2019 General Discussion Forum
Topic: Font size.
Replies: 7
Views: 288

Re: Font size.

ok I poked the size button first
by John Warren
Sun Oct 20, 2019 10:11 am
Forum: 2019 General Discussion Forum
Topic: Font size.
Replies: 7
Views: 288

Font size.

When using my iPhone to browse the forum I see Steve Jelf’s posts are much easy to read. I am looking at changing my posts to also make them easier to read. I have poked the size size=150][/size] button but it doesn’t seem to change anything. I probably have to do it first thing and not midway throu...
by John Warren
Sat Oct 19, 2019 9:38 am
Forum: Classifieds - Parts
Topic: WTB Winfield 5V parts
Replies: 9
Views: 457

Re: WTB Winfield 5V parts

I am still looking for 6V stuff. Thanks
by John Warren
Sat Oct 19, 2019 9:36 am
Forum: Classifieds - Parts
Topic: WTB Winfield 5V parts
Replies: 9
Views: 457

Re: WTB Winfield 5V parts

Gene Morgan probably has what you need. DON’T deal with him.
by John Warren
Sat Oct 19, 2019 8:49 am
Forum: 2019 General Discussion Forum
Topic: Has anyone bought from Gene Morgan?
Replies: 23
Views: 1743

Re: Has anyone bought from Gene Morgan?

Wow. I get a response to my add wanting to buy a Windfield carburetor from Wendell loadholt telling me to try gene morgan. He sent me a photo of a Windfield but wasn’t the one I was looking for. I did some research on that carburetor trying to see if it was still something worth buying. The only pho...
by John Warren
Sat Oct 19, 2019 7:49 am
Forum: 2019 General Discussion Forum
Topic: What is the vacuum test telling me?
Replies: 22
Views: 1406

Re: What is the vacuum test telling me?

Hi Steve, You may have already done this, but you can check valve , ring and head gasket problems by doing a leak down test. Take out all of your plugs, pull your pistons top dead center on compression stroke, put your car in hi gear and block your tires. Now build up an air hose and fitting that wi...
by John Warren
Mon Oct 07, 2019 1:06 am
Forum: 2019 General Discussion Forum
Topic: Hard starting: I'm out of ideas.
Replies: 38
Views: 1870

Re: Hard starting: I'm out of ideas.

Hi Steve, You say you now have to jack up the rear wheel when you start it cold and you didn't use to have to do that. Did you change the clutch when did the rebuild? Have you checked the adjustment. My 25 RPU has a ford clutch, I have to jack up the rear wheel to start it cold with the crank. My 26...
by John Warren
Sat Oct 05, 2019 7:48 pm
Forum: 2019 General Discussion Forum
Topic: A nice send off
Replies: 10
Views: 786

Re: A nice send off

Very nicely done. I’m sure he would have approved! Bless you and your family.
by John Warren
Sat Oct 05, 2019 7:27 pm
Forum: 2019 General Discussion Forum
Topic: KIDS AND CARS
Replies: 46
Views: 2368

Re: KIDS AND CARS

Grand niece and nephew
3889054D-736B-49B0-8248-CF1E3DF76B7E.jpeg
by John Warren
Sat Oct 05, 2019 9:08 am
Forum: 2019 General Discussion Forum
Topic: Rear axle seal vs. shims
Replies: 14
Views: 807

Re: Rear axle seal vs. shims

Rich looks like a great idea and thanks for sharing. I have had the same problem. This is what I have done with some success.
19E42A19-0B28-4486-98F2-96AD1E5AC410.jpeg
by John Warren
Sun Sep 29, 2019 10:01 am
Forum: 2019 General Discussion Forum
Topic: OPS!! dropped a washer!
Replies: 27
Views: 1369

Re: OPS!! dropped a washer!

Dick, Did you tell your son he was a God Da__ Genius. What a great Idea!! Thanks
by John Warren
Sun Sep 29, 2019 9:39 am
Forum: 2019 General Discussion Forum
Topic: Source of knock found!
Replies: 6
Views: 617

Re: Source of knock found!

I have rounded up cranks using emery cloth, more of an emergency repair or get you by for a while. Another thing to check is barreling of the journals, this is where the crank pins are fatter in the middle. This is caused from twisted rods. Just wondering if the same guy did the main bearings.( not ...
by John Warren
Sat Sep 28, 2019 8:25 am
Forum: 2019 General Discussion Forum
Topic: Covered Bridge Tour
Replies: 26
Views: 2262

Re: Covered Bridge Tour

That sure looks like fun, It's on my bucket list. How can we get some notice before it happens. Thanks all for sharing.
by John Warren
Sat Sep 28, 2019 7:38 am
Forum: 2019 General Discussion Forum
Topic: Home-Built HCCT Project
Replies: 37
Views: 2237

Re: Home-Built HCCT Project

Thanks for taking the time to share the build, Great job!! Loved seeing it go together. In the day it would have been as good as it gets. Thanks again.
by John Warren
Sat Sep 28, 2019 7:30 am
Forum: 2019 General Discussion Forum
Topic: Scrap iron
Replies: 17
Views: 1074

Re: Scrap iron

Certain things are needed ! Thanks for sharing, both look like they would work well.
by John Warren
Fri Sep 20, 2019 8:51 pm
Forum: Classifieds - Parts
Topic: WTB Maxwell Fenders
Replies: 8
Views: 445

Re: WTB Maxwell Fenders

Bob, I also need fenders and brackets. I do have some patterns, may be we can have them reproduced?
by John Warren
Fri Sep 20, 2019 8:49 pm
Forum: Classifieds - Parts
Topic: WTB Maxwell Fenders
Replies: 8
Views: 445

Re: WTB Maxwell Fenders

I need a Maxwell # 33 or # 34 head lamp or chimney thanks
by John Warren
Fri Sep 20, 2019 8:45 pm
Forum: 2019 General Discussion Forum
Topic: What do you do when the boss says “I want you to build a car that will beat the fastest racer in the world?”
Replies: 59
Views: 3013

Re: What do you do when the boss says “I want you to build a car that will beat the fastest racer in the world?”

Thanks Rob, I loved it all ! Great comments and additional information.

Did you get the bugs worked out of your race car?
by John Warren
Fri Sep 20, 2019 7:56 pm
Forum: 2019 General Discussion Forum
Topic: Milwaukee to Detroit and back again in a Model T
Replies: 28
Views: 1607

Re: Milwaukee to Detroit and back again in a Model T

Thanks David, Loved reading it. Be safe!
by John Warren
Fri Sep 20, 2019 7:46 pm
Forum: 2019 General Discussion Forum
Topic: Making some crude drawings
Replies: 3
Views: 517

Re: Making some crude drawings

I like it, It looks like you were successful.
by John Warren
Fri Sep 20, 2019 7:41 pm
Forum: 2019 General Discussion Forum
Topic: Here I go again .... to OCF
Replies: 244
Views: 43888

Re: Here I go again .... to OCF

Great times Steve, for now I can only dream about. Thanks so much for taking us along and great to know you are safe and sound! Glad Shorty did well while you were away.
by John Warren
Fri Sep 20, 2019 7:03 pm
Forum: 2019 General Discussion Forum
Topic: Sealing my 12 rivet rear end
Replies: 17
Views: 1096

Re: Sealing my 12 rivet rear end

Its pose to leak !!!! cause if it don't, it is out of earl !!! :lol: Great stuff thanks.
by John Warren
Sun Sep 15, 2019 10:32 am
Forum: Classifieds - Parts
Topic: WTB 6V WINDFIELD CARBURETOR
Replies: 1
Views: 196

Re: WTB 6V WINDFIELD CARBURETOR

windfield.jpeg
by John Warren
Sun Sep 15, 2019 10:27 am
Forum: Classifieds - Parts
Topic: WTB 6V WINDFIELD CARBURETOR
Replies: 1
Views: 196

WTB 6V WINDFIELD CARBURETOR

Hi, I am looking for a Windfield 6 V carburetor, It is an up draft carburetor.
by John Warren
Sat Sep 14, 2019 10:27 am
Forum: 2019 General Discussion Forum
Topic: 14 runs after 40 years.
Replies: 6
Views: 1000

Re: 14 runs after 40 years.

:lol:
by John Warren
Fri Sep 13, 2019 11:39 pm
Forum: 2019 General Discussion Forum
Topic: Foto of the Day
Replies: 294
Views: 20236

Re: Foto of the Day

James, love the truck, is it yours? Nice photo Thanks
by John Warren
Thu Sep 05, 2019 7:21 pm
Forum: 2019 General Discussion Forum
Topic: SCAT crank or not?
Replies: 13
Views: 1103

Re: SCAT crank or not?

I put one in my Dad's engine during rebuild. High compression pistons stock head and cam, advanced 5 deg. new snyder rods with babbitt I did balance the crank flywheel rods and pistons, should have also balanced the drums. She runs like a top with good power but is not as smooth as I would have like...
by John Warren
Sun Sep 01, 2019 4:14 pm
Forum: Classifieds - Parts
Topic: 6V Windfield
Replies: 0
Views: 301

6V Windfield

I am looking for a 6V Windfield carburetor.
91E8111F-D07F-405C-9EF8-9F68EF85F577.jpeg
by John Warren
Sun Sep 01, 2019 10:39 am
Forum: 2019 General Discussion Forum
Topic: Barn find, or better?
Replies: 22
Views: 1784

Re: Barn find, or better?

I would be interested in the a parts
by John Warren
Sun Sep 01, 2019 8:22 am
Forum: 2019 General Discussion Forum
Topic: Here I go again .... to OCF
Replies: 244
Views: 43888

Re: Here I go again .... to OCF

Hi Steve, Wish I were tagging along. How many miles on the new engine now? Thanks for taking us along... be safe and hopefully there will be a few more folks that can accommodate you in some way during your adventure.
by John Warren
Sat Aug 31, 2019 9:38 pm
Forum: 2019 General Discussion Forum
Topic: A different option to the fuel sediment bowl
Replies: 29
Views: 1522

Re: A different option to the fuel sediment bowl

Scott you are so smart. You are absolutely correct about a $50 dollar part. For an aircraft, parts are much more expensive. The fuel bowl is the same design on my Cessna 120 with a glass bowl. On my Cessna 150 the bowl is also glass but a little different in design and as you said not a $50 dollar p...
by John Warren
Sat Aug 31, 2019 10:34 am
Forum: 2019 General Discussion Forum
Topic: 14 runs after 40 years.
Replies: 6
Views: 1000

14 runs after 40 years.

Danny Lorenzi’s 14 roadster runs after 40 year restoration. Still a few things to do, but we took it on our breakfast run.
6B0D9FA7-E175-4A73-9575-A947E046F969.jpeg
by John Warren
Sat Aug 31, 2019 9:18 am
Forum: 2019 General Discussion Forum
Topic: What have you done to your T in August
Replies: 94
Views: 5242

Re: What have you done to your T in August

Pat, no drive shaft needed. :lol:
by John Warren
Sat Aug 31, 2019 9:06 am
Forum: 2019 General Discussion Forum
Topic: A different option to the fuel sediment bowl
Replies: 29
Views: 1522

Re: A different option to the fuel sediment bowl

Good choice, If your worried about a broken bowl, carry a new one. I absolutely don't think there is a safety problem that didn't exist with the original. I run the same one on my race car and my 26 touring. My airplanes also run the same thing.
by John Warren
Sat Aug 31, 2019 8:53 am
Forum: 2019 General Discussion Forum
Topic: My T broke my wrist DAMN
Replies: 36
Views: 2014

Re: My T broke my wrist DAMN

So sorry to hear about the injury, I to, am guilty of cranking the cars right handed, mostly because my right arm is more capable of starting it. Yes I have had it back-fire but so far have always been able to hold it from spinning backwards. I'm getting older and better start using the correct way ...
by John Warren
Tue Aug 27, 2019 8:29 pm
Forum: 2019 General Discussion Forum
Topic: What have you done to your T in August
Replies: 94
Views: 5242

Re: What have you done to your T in August

Thanks Andre, great photos of the old bikes. Thanks jw
by John Warren
Sat Aug 10, 2019 8:07 pm
Forum: 2019 General Discussion Forum
Topic: What have you done to your T in August
Replies: 94
Views: 5242

Re: What have you done to your T in August

Had to do a shade tree repair this morning :lol:
E1AC3F7A-F352-4369-B11A-86F3A16874AA.jpeg
by John Warren
Sat Aug 10, 2019 7:34 pm
Forum: 2019 General Discussion Forum
Topic: Resurrection of a 1909 Model T
Replies: 59
Views: 6099

Re: Resurrection of a 1909 Model T

The car definitely has the WOW factor, Thanks Tony for sharing your great car.
by John Warren
Sat Aug 10, 2019 7:23 pm
Forum: 2019 General Discussion Forum
Topic: 24 Touring Barn Car Revival - Part 3
Replies: 282
Views: 16613

Re: 24 Touring Barn Car Revival - Part 3

Don, Great journey, Thanks for taking us along. I'm sure that it was an absolutely great feeling to finally drive her YAAAA. You can adjust the carburetor prior to getting in the seat. It is best if you have the adjustment rod installed so you ca adjust it from the seat. She will blubber when she is...
by John Warren
Sat Aug 10, 2019 7:02 pm
Forum: 2019 General Discussion Forum
Topic: What have you done to your T in August
Replies: 94
Views: 5242

Re: What have you done to your T in August

Looks like your getting close Steve. :P
by John Warren
Sun Aug 04, 2019 9:02 am
Forum: 2019 General Discussion Forum
Topic: What front end is this
Replies: 8
Views: 812

Re: What front end is this

Probably use as a trailer axle
7BB34578-CCAE-4FC7-8F8C-208266122AA2.jpeg
by John Warren
Sun Aug 04, 2019 8:34 am
Forum: 2019 General Discussion Forum
Topic: Foto of the Day
Replies: 294
Views: 20236

Re: Foto of the Day

Nice Ed. Could easily be an original photo.
by John Warren
Sun Aug 04, 2019 8:25 am
Forum: 2019 General Discussion Forum
Topic: Line boring early block
Replies: 8
Views: 1001

Re: Line boring early block

Thanks for sharing Eric. Always great to hear from you.
by John Warren
Sun Aug 04, 2019 8:21 am
Forum: 2019 General Discussion Forum
Topic: Scat Rods 2T7000
Replies: 15
Views: 1192

Re: Scat Rods 2T7000

That’s too bad about the Snyder’s rods. I thought they were great built with dippers. 😢.
by John Warren
Sun Jul 28, 2019 6:51 pm
Forum: 2019 General Discussion Forum
Topic: HELP. MODEL T NOISE
Replies: 36
Views: 2484

Re: HELP. MODEL T NOISE

Also seen cam bearings make noise.
by John Warren
Sun Jul 28, 2019 6:50 pm
Forum: 2019 General Discussion Forum
Topic: HELP. MODEL T NOISE
Replies: 36
Views: 2484

Re: HELP. MODEL T NOISE

Main bearings
by John Warren
Thu Jul 25, 2019 11:35 pm
Forum: 2019 General Discussion Forum
Topic: Foto of the Day
Replies: 294
Views: 20236

Re: Foto of the Day

Great photos. Thanks for sharing
by John Warren
Wed Jul 17, 2019 10:42 am
Forum: Classifieds - Parts
Topic: Need a good screw
Replies: 6
Views: 633

Re: Need a good screw

😂
by John Warren
Wed Jul 17, 2019 9:44 am
Forum: Classifieds - Parts
Topic: OT aircraft
Replies: 3
Views: 452

OT aircraft

1964 Cessna 150 D. 2420 TTA. 619 SMOH. Straight tail, manual flaps. New tires. $14,000
D4604A76-1B36-49CE-8631-C816191EC567.jpeg
by John Warren
Mon Jul 15, 2019 8:49 am
Forum: 2019 General Discussion Forum
Topic: When there is smoke there must be fire.
Replies: 11
Views: 1014

Re: When there is smoke there must be fire.

Lucas. Prince of darkness 😂. And that is no joke.
by John Warren
Mon Jul 15, 2019 8:28 am
Forum: 2019 General Discussion Forum
Topic: Going to Model T Haven tomorrow. ......
Replies: 12
Views: 1157

Re: Going to Model T Haven tomorrow. ......

Hi Donnie. I went there last month and all was well. Mark just got a bunch of great stuff. Lots of aftermarket rare stuff. Check it out. I purchased 27 roadster pu parts and some unusual wheels.
E4F220F2-71D8-4280-B715-6999D02D1347.jpeg
by John Warren
Mon Jul 15, 2019 8:14 am
Forum: 2019 General Discussion Forum
Topic: Another What it is??
Replies: 3
Views: 466

Re: Another What it is??

Looks like a rear axle wheel seal retainer.
by John Warren
Thu Jul 11, 2019 7:36 pm
Forum: 2019 General Discussion Forum
Topic: What have you done to your Model T in July?
Replies: 113
Views: 7116

Re: What have you done to your Model T in July?

Forest, nice TT , Steve, looks like you should have a great engine and I see you used your special engine stand. :D I enjoyed meeting Mike.
by John Warren
Thu Jul 11, 2019 7:26 pm
Forum: 2019 General Discussion Forum
Topic: 1927 Speedster Build
Replies: 3
Views: 403

Re: 1927 Speedster Build

Sweet, keep us posted. It is going to be a great ride.
by John Warren
Wed Jul 10, 2019 8:51 am
Forum: 2019 General Discussion Forum
Topic: High speed clutch adjustment
Replies: 20
Views: 1912

Re: High speed clutch adjustment

Joe , With the cover off, check to see if arms bottoming out against the clutch face. You can turn the adjustment screws in some to get clearance thus applying more pressure to the clutch.
by John Warren
Tue Jul 09, 2019 8:12 am
Forum: 2019 General Discussion Forum
Topic: Fitting beaded edge tyres.
Replies: 6
Views: 499

Re: Fitting beaded edge tyres.

I like it, thanks
by John Warren
Tue Jul 09, 2019 8:11 am
Forum: 2019 General Discussion Forum
Topic: Outside oil line
Replies: 6
Views: 654

Re: Outside oil line

Cameron, Nice job I am sure it w ill work great.