Search found 32 matches

by Rich Huggins
Fri May 22, 2020 7:57 pm
Forum: Classifieds - Parts
Topic: 4 main roller bearing ball cap
Replies: 0
Views: 130

4 main roller bearing ball cap

4 main roller bearing ball cap needed
by Rich Huggins
Sat May 16, 2020 1:28 pm
Forum: Classifieds - Parts
Topic: atwater kent model h distributor
Replies: 0
Views: 136

atwater kent model h distributor

Hi need drive gears for a atwater kent model H Distributor or just cam gear they look spiders gears
by Rich Huggins
Fri May 15, 2020 2:23 pm
Forum: General Discussion Forum (started 2019)
Topic: atwater kent model h distributor
Replies: 1
Views: 144

atwater kent model h distributor

Dose any one know were i can get a atwater kent model h cam shaft gear looks like a pinion gear
by Rich Huggins
Fri Apr 24, 2020 9:22 pm
Forum: General Discussion Forum (started 2019)
Topic: Exhaust Manifold Running Red
Replies: 5
Views: 443

Re: Exhaust Manifold Running Red

At low idle 1/8 to 1/4 on the spark rod adjust carb rich to lean then back to good idle just sitting with the garage fan on at high speed, manifold Cherie red! Driving 3/4 to 1/2 on the throttle 1/2 to 3/4 on the spark, no intake or exhaust leak at 1/2 to 3/4 on the throttle, the carb whistles like ...
by Rich Huggins
Fri Apr 24, 2020 8:31 pm
Forum: General Discussion Forum (started 2019)
Topic: Exhaust Manifold Running Red
Replies: 1
Views: 182

Exhaust Manifold Running Red

Hi my exhaust manifold runs bright red while driving, i smelled something burning ! oh no my floor board is on fire. Luckily i had water, burnt half way through the 3 piece floor board covered it with a sheet metal heat shield. I did drive home with no floor boards ,dam that was hot on the feet is t...
by Rich Huggins
Fri Apr 24, 2020 8:19 pm
Forum: General Discussion Forum (started 2019)
Topic: Exhaust Manifold Running Red
Replies: 5
Views: 443

Exhaust Manifold Running Red

Hi my exhaust manifold runs bright red while driving, i smelled something burning ! oh no my floor board is on fire. Luckily i had water, burnt half way through the 3 piece floor board covered it with a sheet metal heat shield. I did drive home with no floor boards ,dam that was hot on the feet is t...
by Rich Huggins
Sun Apr 19, 2020 10:25 pm
Forum: Live Video Webinars
Topic: Model T Webinar #2 - Coil Testing/Tuning
Replies: 66
Views: 3393

Re: Coil Testing/Tuning Webinar

Well i did not bench test coil box hardly any spark will not start take out and bench test box and coils tomorrow still interested
by Rich Huggins
Sat Apr 18, 2020 6:43 pm
Forum: Live Video Webinars
Topic: Model T Webinar #2 - Coil Testing/Tuning
Replies: 66
Views: 3393

Re: Coil Testing/Tuning Webinar

That's funny i'am working on my coils right now. Happy Oh that's my car name was running fine until l i painted the dash, got over spray every were! cleaned every thing down look's good again. Started Happy up, runs fine off idle started to back fire! started back fireing popping out carb dam i mess...
by Rich Huggins
Wed Apr 08, 2020 10:45 am
Forum: General Discussion Forum (started 2019)
Topic: 26-27 brake band
Replies: 0
Views: 158

26-27 brake band

need Kevlar brake band for 26-27 brake drum wide band only
by Rich Huggins
Sun Apr 05, 2020 4:19 pm
Forum: General Discussion Forum (started 2019)
Topic: 4th main
Replies: 10
Views: 696

Re: 4th main

I have been looking for month's to get my hands on a 4 rear main sealed bearing ball cap
by Rich Huggins
Thu Apr 02, 2020 7:34 am
Forum: General Discussion Forum (started 2019)
Topic: lighten flywheel
Replies: 8
Views: 523

lighten flywheel

Want to lighten flywheel, no mag pro an con. comets needed engine will rev faster reach higher rpm and will run smoother any one in az that can machine the flywheel
by Rich Huggins
Mon Mar 16, 2020 2:44 pm
Forum: General Discussion Forum (started 2019)
Topic: pressure plate
Replies: 3
Views: 775

Re: pressure plate

i have a pin on clutch plate that is stuck down and the clutch finger has a lot of play can i take out the clutch housing bolts to the brake drum so see the damage i do not have the time to pull the engine out and the rear end
by Rich Huggins
Wed Mar 11, 2020 11:38 pm
Forum: Classifieds - Parts
Topic: WTB 12 Tooth Pinion
Replies: 9
Views: 791

Re: WTB 12 Tooth Pinion

wanted 40 tooth recess ping gear dose any one have
by Rich Huggins
Wed Mar 11, 2020 8:47 pm
Forum: General Discussion Forum (started 2019)
Topic: pressure plate
Replies: 3
Views: 775

Re: pressure plate

any one have any advice
by Rich Huggins
Wed Mar 11, 2020 5:46 pm
Forum: General Discussion Forum (started 2019)
Topic: pressure plate
Replies: 3
Views: 775

pressure plate

Took trans cover off to check bands and clutch adjust while looking at the clutch fingers one has a lot of play bad word **** the pin is all the way in and wont come out 1/4 in play don't know but think this is bad it drives fine don't here any thing broken plate tore up clutch disc o no $$$$$ lmao
by Rich Huggins
Wed Mar 11, 2020 2:34 pm
Forum: Classifieds - Parts
Topic: Lot Differential parts at Chickasha
Replies: 9
Views: 1201

Re: Lot Differential parts at Chickasha

looking for 39 or 40 ring gear for a 12 or 13 pinion ring gear is cut back so it will accommodate large pinion
by Rich Huggins
Fri Feb 21, 2020 9:49 am
Forum: General Discussion Forum (started 2019)
Topic: Anyone use a Model A fuel shutoff on a T?
Replies: 5
Views: 664

Re: Anyone use a Model A fuel shutoff on a T?

Hi i purchased a gas shut off valve from one of the top suppliers. Has been on the car about 6 month and it seeps gas i was told to push down wen i turn it off still seeps it is a all brass unit i keep a paper towel on it and change it often there is a water heater in my gauge so i leave the side do...
by Rich Huggins
Sat Feb 08, 2020 5:07 pm
Forum: General Discussion Forum (started 2019)
Topic: 4 th main bearing cap
Replies: 8
Views: 544

Re: 4 th main bearing cap

Sorry double post I want ball cap with bearing and seal more support to support auxiliary trans in put shaft
by Rich Huggins
Sat Feb 08, 2020 2:53 pm
Forum: General Discussion Forum (started 2019)
Topic: 4 th main bearing cap
Replies: 8
Views: 544

Re: 4 th main bearing Ball cap

The bearing cap that is on the back of supports rear trans clutch and trans assembly Sorry my bad its called a Bearing Ball Cap want one with a bearing and sleeve can not find one anywhere lang,s part #3369bbd
by Rich Huggins
Sat Feb 08, 2020 2:05 pm
Forum: General Discussion Forum (started 2019)
Topic: 4 th main bearing cap
Replies: 8
Views: 544

Re: 4 th main bearing Ball cap

The bearing cap that is on the back of supports rear trans clutch and trans assembly Sorry my bad its called a Bearing Ball Cap want one with a bearing and sleeve can not find one anywhere lang,s part #3369bbd
by Rich Huggins
Sat Feb 08, 2020 1:05 pm
Forum: General Discussion Forum (started 2019)
Topic: 4 th main bearing cap
Replies: 8
Views: 544

4 th main bearing cap

Looking for rear 4 th main bearing cap none of the supply shop,s have it who makes this and were can i get one
by Rich Huggins
Thu Jan 23, 2020 4:46 am
Forum: Classifieds - Parts
Topic: CUSTOMER APPRECIATION SALE 20%
Replies: 46
Views: 4606

Re: CUSTOMER APPRECIATION SALE 20%

Wish i had the money to buy the business when will you be closing the store this will be a blow to the model t community thank you for all the years may god bless you
by Rich Huggins
Fri Jan 03, 2020 4:34 am
Forum: Classifieds - Parts
Topic: FS: Hand painted / assembled radiator caps
Replies: 7
Views: 1324

Re: FS: Hand painted / assembled radiator caps

can you put santa on a chrome cap
by Rich Huggins
Tue Dec 31, 2019 3:42 am
Forum: General Discussion Forum (started 2019)
Topic: 13 pinnion gear
Replies: 2
Views: 468

Re: 13 pinnion gear

Were do i find the proper ring gear 40 tooth with recess
by Rich Huggins
Mon Dec 30, 2019 1:32 pm
Forum: General Discussion Forum (started 2019)
Topic: 13 pinnion gear
Replies: 2
Views: 468

13 pinnion gear

high gear ratio 13 tooth pinnion install on 40 tooth stock ring gear can i do it 1923 t touring 3speed bg warnner t 90 trans
by Rich Huggins
Fri Dec 27, 2019 8:09 am
Forum: General Discussion Forum (started 2019)
Topic: 23 model t touring head light reflectors
Replies: 5
Views: 563

23 model t touring head light reflectors

Head light reflectors need to be cleaned, Rust film very little , finger prints how do i clean look,s like a delicate plating
by Rich Huggins
Thu Nov 21, 2019 7:56 pm
Forum: Classifieds - Parts
Topic: SOLD Differential parts
Replies: 5
Views: 735

Re: Differential parts

have not heard back on universal joint ready to by
by Rich Huggins
Wed Nov 20, 2019 6:44 am
Forum: Classifieds - Parts
Topic: SOLD Differential parts
Replies: 5
Views: 735

Re: Differential parts

interested in drive shaft universal joint offer 10.00
by Rich Huggins
Fri Nov 15, 2019 6:44 pm
Forum: Classifieds - Parts
Topic: Aluminum Hogsheads For Sale
Replies: 12
Views: 1658

Re: Aluminum Hogsheads For Sale

payment sent
by Rich Huggins
Thu Nov 14, 2019 3:35 pm
Forum: Classifieds - Parts
Topic: Aluminum Hogsheads For Sale
Replies: 12
Views: 1658

Re: Aluminum Hogsheads For Sale

paypay can pay today rhuggie2@aol.com
by Rich Huggins
Wed Nov 13, 2019 9:35 pm
Forum: Classifieds - Parts
Topic: Aluminum Hogsheads For Sale
Replies: 12
Views: 1658

Re: Aluminum Hogsheads For Sale

rich huggins 44267 w. cypress ln, maricopa az 85138 ph. 520-827-0295 35.00 for hog head how much shippins
by Rich Huggins
Mon Nov 11, 2019 9:32 am
Forum: Classifieds - Parts
Topic: Aluminum Hogsheads For Sale
Replies: 12
Views: 1658

Re: Aluminum Hogsheads For Sale

do you still have drilled hog s head 35 how much for shipping and hou do i pay