Thanks
Brass speedometer
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Randall strickland
Topic author - Posts: 156
- Joined: Sun Jan 06, 2019 5:50 pm
- First Name: Randall
- Last Name: Strickland
- Location: lambsburg va
Brass speedometer
Installing speedometer on a Freinds speedster and the inside cable is about one inch to short, is there a way to shorten housing?
Thanks
Thanks
-
Randall strickland
Topic author - Posts: 156
- Joined: Sun Jan 06, 2019 5:50 pm
- First Name: Randall
- Last Name: Strickland
- Location: lambsburg va
Re: Brass speedometer
Calble not a chain
-
Randall strickland
Topic author - Posts: 156
- Joined: Sun Jan 06, 2019 5:50 pm
- First Name: Randall
- Last Name: Strickland
- Location: lambsburg va
Re: Brass speedometer
Tried to post picture of cable but will not post
-
speedytinc
- Posts: 4725
- Joined: Fri Feb 12, 2021 12:24 pm
- First Name: john
- Last Name: karvaly
- * REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
- Location: orange, ca
- Board Member Since: 2020
Re: Brass speedometer
The common SW steel housings ends are crimped on, so yes is possible to cut @ the edge of the crimped end, peel the outer cable out of the crimped end, force a rod into the end to uncrimp/expand & re crimp.
I wounld not do this unless the housing had damage near the end. (this issue did recently come up for me.)
Make a new longer cable or make an extended cable end.
I wounld not do this unless the housing had damage near the end. (this issue did recently come up for me.)
Make a new longer cable or make an extended cable end.
-
jiminbartow
- Posts: 2433
- Joined: Sun Jan 06, 2019 10:55 pm
- First Name: James
- Last Name: Patrick
- * REQUIRED* Type and Year of Model Ts owned: 1926 Coupe
- Location: Bartow, FL
- Board Member Since: 2001
Re: Brass speedometer
Let Russ Furstow do it.
-
KimDobbins
- Posts: 1554
- Joined: Sun Jan 06, 2019 12:16 pm
- First Name: Kim
- Last Name: Dobbins
- * REQUIRED* Type and Year of Model Ts owned: 1909 touring, 1910 touring, 1913 touring, 1916 couplet, 1925 roadster pickup.
- Location: Southern California
Re: Brass speedometer
You can always use the original chain links. To adjust the length, simply add or subtract a link.
-
Russ_Furstnow
- Posts: 370
- Joined: Tue Jan 08, 2019 9:01 am
- First Name: Russ
- Last Name: Furstnow
- * REQUIRED* Type and Year of Model Ts owned: 1911 Torpedo,1913 Touring, 1914 Runabout, 1915 Coupelet, 1916 Coupelet, 1917 Coupelet
- Location: Flagstaff, AZ
- MTFCA Life Member: YES
Re: Brass speedometer
The speedometer pictured is a "high speed" speedometer. It takes a 1:1 drive and not a 2.5:1 drive. It appears that the road gear and the swivel drive will not run the speedometer accurately. The cable should be around 48" long, and the length of the outer housing can be shortened. I hope this helps, Russ Furstnow