We Have All Been Here, Right?

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
User avatar

Topic author
Henry K. Lee
Posts: 2883
Joined: Sun Jan 06, 2019 11:09 am
First Name: Henry
Last Name: Lee
Location: South Pittsburg, TN
MTFCA Number: 479
MTFCA Life Member: YES

We Have All Been Here, Right?

Post by Henry K. Lee » Tue Aug 06, 2019 8:52 pm

THE PYRAMID OF PERSUASION!
Image 8-5-19 at 8.27 PM.jpg


Wayne Sheldon
Posts: 1588
Joined: Sun Jan 06, 2019 3:13 pm
First Name: Wayne
Last Name: Sheldon
Location: Grass Valley Califunny, USA
Board Member Since: 2005

Re: We Have All Been Here, Right?

Post by Wayne Sheldon » Wed Aug 07, 2019 12:35 am

I do like the "I wasn't asking"!
Also, a lot of truth to that "Can't be tight if its a liquid".
Good stuff! Thanks for sharing those.

User avatar

Steve Jelf
Posts: 2489
Joined: Fri Jan 04, 2019 9:37 pm
First Name: Steve
Last Name: Jelf
Location: Parkerfield, Kansas
MTFCA Number: 16175
MTFCI Number: 14758
Board Member Since: 2007
Contact:

Re: We Have All Been Here, Right?

Post by Steve Jelf » Wed Aug 07, 2019 1:01 am

All that's missing is the six-foot cheater stuck on the handle of the big wrench. :D
The inevitable often happens.
1915 Runabout
1923 Touring


Rich Bingham
Posts: 1096
Joined: Sun Jan 06, 2019 11:23 am
First Name: Rich
Last Name: Bingham
Location: Blackfoot, Idaho

Re: We Have All Been Here, Right?

Post by Rich Bingham » Wed Aug 07, 2019 8:06 am

wayne sheldon wrote:
Wed Aug 07, 2019 12:35 am
. . . a lot of truth to that "Can't be tight if its a liquid".
:lol: you can disassemble practically anything with a cutting torch ! :lol:
"Get a horse !"

User avatar

JTT3
Posts: 186
Joined: Sun Jan 06, 2019 11:57 am
First Name: John T
Last Name: Tannehill III
Location: Hot Coffee, MS

Re: We Have All Been Here, Right?

Post by JTT3 » Wed Aug 07, 2019 9:27 am

Henry, I noticed you missed in your tool assortment the BFH as an adjunct to the other tools.


Dennis Prince
Posts: 182
Joined: Sun Jan 06, 2019 2:36 pm
First Name: Dennis
Last Name: Prince
Location: Madras Oregon
MTFCA Number: 22802
Board Member Since: 1999

Re: We Have All Been Here, Right?

Post by Dennis Prince » Wed Aug 07, 2019 10:14 am

By the time I get to the directional forge there is usually a box of band aids involved as well.

User avatar

Ruxstel24
Posts: 1857
Joined: Sun Jan 06, 2019 11:25 am
First Name: Dave
Last Name: Hanlon
Location: NE Ohio
MTFCA Number: 50191
Board Member Since: 2018

Re: We Have All Been Here, Right?

Post by Ruxstel24 » Wed Aug 07, 2019 10:33 am

I had to heat a carrier bearing housing on a front axle half shaft the other day...I had to get away for a couple hours from the garage being smoked up so bad !! It was rough ! :shock:

Sometimes the flaming nut buster is the only option. 🔥

Post Reply Previous topicNext topic