I am needing an exhaust manifold for an AKRON-HAL overhead set up that uses the tubes and ball bearings to actuate the valves. Any leads greatly appreciated.
Thank you, Bruce
WTB. Exhaust manifold for AKRON-HAL overhead
-
Mark Gregush
- Posts: 5370
- Joined: Sat Jan 05, 2019 1:57 pm
- First Name: Mark
- Last Name: Gregush
- * REQUIRED* Type and Year of Model Ts owned: 1925 cutdown PU, 1948 F2 Ford flat head 6 pickup 3 speed
- Location: Portland Or
- Board Member Since: 1999
Re: WTB. Exhaust manifold for AKRON-HAL overhead
Have you checked with Kevin? (Guessing you have but putting it out there anyway)
viewtopic.php?t=11172
I have only seen one of these units in the wild and that was over 20 years ago and don't recall if that one had the manifolds.
viewtopic.php?t=11172
I have only seen one of these units in the wild and that was over 20 years ago and don't recall if that one had the manifolds.
I know the voices aren't real but damn they have some good ideas! 
1925 Cut down pickup
1948 Ford F2 pickup
1925 Cut down pickup
1948 Ford F2 pickup
-
civinwt
Topic author - Posts: 28
- Joined: Sun Jan 06, 2019 4:54 pm
- First Name: Bruce
- Last Name: Hopkins
- * REQUIRED* Type and Year of Model Ts owned: 11 Torpedo, 20TT 1Ton, 27 Runabout
- Location: Victoria BC Canada
Re: WTB. Exhaust manifold for AKRON-HAL overhead
Mark:
thank you for the suggestion., I have just e-mailed Kevin.
thank you for the suggestion., I have just e-mailed Kevin.
-
Kevin Pharis
- Posts: 1558
- Joined: Thu Jan 10, 2019 3:54 pm
- First Name: Kevin
- Last Name: Pharis
- Location: Sacramento CA
- Contact:
Re: WTB. Exhaust manifold for AKRON-HAL overhead
Hey there Bruce,
If you had asked me last year, I probably would have sold mine. Bout that time I even offered to loan it to the Speedway Museum
I have since decided to use mine, but did make up some header flanges that I am willing to part with. They are 1/2” thick stainless steel
If you had asked me last year, I probably would have sold mine. Bout that time I even offered to loan it to the Speedway Museum
I have since decided to use mine, but did make up some header flanges that I am willing to part with. They are 1/2” thick stainless steel
-
Kevin Pharis
- Posts: 1558
- Joined: Thu Jan 10, 2019 3:54 pm
- First Name: Kevin
- Last Name: Pharis
- Location: Sacramento CA
- Contact:
Re: WTB. Exhaust manifold for AKRON-HAL overhead
Just in case, here is a pic of the manifold Bruce is looking for…
Please disregard all the shiny stuff
-
civinwt
Topic author - Posts: 28
- Joined: Sun Jan 06, 2019 4:54 pm
- First Name: Bruce
- Last Name: Hopkins
- * REQUIRED* Type and Year of Model Ts owned: 11 Torpedo, 20TT 1Ton, 27 Runabout
- Location: Victoria BC Canada
Re: WTB. Exhaust manifold for AKRON-HAL overhead
Kevin, thank you for the offer of the flanges, and thank you for the picture of desired manifold.
When I acquired the rocker assembly from you, you included a pair of the pictured exhaust flanges.
I too want to run the exhaust under the frame so as to not modify the torpedo hood in any way.
When I acquired the rocker assembly from you, you included a pair of the pictured exhaust flanges.
I too want to run the exhaust under the frame so as to not modify the torpedo hood in any way.