NEW 12 tooth pinion thank you Chaffin’s
-
Topic author - Posts: 1855
- Joined: Sun Jan 06, 2019 11:57 am
- First Name: John
- Last Name: Tannehill
- Location: Hot Coffee, MS
NEW 12 tooth pinion thank you Chaffin’s
The vendor contacted us & has them in stock. Thanks Mark & Dave at Chaffin’s Garage!
Thanks John
Thanks John
Last edited by JTT3 on Fri Jul 28, 2023 10:47 pm, edited 3 times in total.
-
- Posts: 4725
- Joined: Fri Feb 12, 2021 12:24 pm
- First Name: john
- Last Name: karvaly
- * REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
- Location: orange, ca
- Board Member Since: 2020
Re: Any one have a NEW or very good used 12 tooth pinion they’d sell?
Did he contact Chaffins? They had a barrel full.
-
Topic author - Posts: 1855
- Joined: Sun Jan 06, 2019 11:57 am
- First Name: John
- Last Name: Tannehill
- Location: Hot Coffee, MS
Re: Any one have a NEW or very good used 12 tooth pinion they’d sell?
Dave said they were out
-
- Posts: 1419
- Joined: Tue Jan 08, 2019 10:53 am
- First Name: Terry
- Last Name: Woods
- * REQUIRED* Type and Year of Model Ts owned: 1927 Model T coupe, 1926 4 door sedan
- Location: Cibolo (San Antonio), TX
Re: Any one have a NEW or very good used 12 tooth pinion they’d sell?
Yes, Chaffin's is the manufacturer. The would be buyer needs to contact them.
-
Topic author - Posts: 1855
- Joined: Sun Jan 06, 2019 11:57 am
- First Name: John
- Last Name: Tannehill
- Location: Hot Coffee, MS
Re: Any one have a NEW or very good used 12 tooth pinion they’d sell?
I’ve contacted Chaffins they are out right now. Still looking!
-
- Posts: 4343
- Joined: Sat Jan 12, 2019 12:11 pm
- First Name: Mark
- Last Name: Chaffin
- * REQUIRED* Type and Year of Model Ts owned: 1911 Speedster, 1927 Lake Roadster
- Location: Lake Elsinore
- Board Member Since: 2001
Re: Any one have a NEW or very good used 12 tooth pinion they’d sell?
We just obtained a small batch of 12 tooth pinions from our gear cutter. Only took us over a year to get them. Whole supplies last. Thank you.
-
- Posts: 266
- Joined: Tue Jan 08, 2019 10:42 pm
- First Name: Noel
- Last Name: Chicoine
- * REQUIRED* Type and Year of Model Ts owned: 1920 roadster, 1923 Touring, 1926 Coupe
- Location: Pierre, South Dakota
- Board Member Since: 2005
Re: NEW 12 tooth pinion thank you Chaffin’s
You may need to shim a Ruckstell or recessed ring gear as I don't believe any were made to accept a 12 tooth that is smaller diameter than a 13 and bigger than an 11 tooth. I made a large ring gear shim from a 1/16 sheet of aluminum to get my ring-pinion clearance. Stacking 4-5 thinner shims may be asking for sheared ring gear bolts.
-
- Posts: 4249
- Joined: Sun Jan 06, 2019 3:13 pm
- First Name: Wayne
- Last Name: Sheldon
- * REQUIRED* Type and Year of Model Ts owned: 1915 Runabout 1913 Speedster
- Location: Grass Valley California, USA
- Board Member Since: 2005
Re: NEW 12 tooth pinion thank you Chaffin’s
Personally, I would not trust aluminum for that type of a shim. It has enough "give" that it could lead to shearing the bolts. I have seen other places where aluminum was tried for shimming to fit, and seen it fail. I have not seen it used for a ring gear, but it makes sense to me that it might not be tough enough. The ring gear takes a lot of beating from driven torque and braking, that anything that allows any "give" at all would likely lead to failure.
My opinion.
My opinion.