It supposedly allows use of an NH without punching a hole in the block Anyone use it and could send me a few pictures of how it is installed??
https://www.modeltford.com//item/6299CL.aspx
David Kriegel Mishawaka IN dakriegel@yahoo.com
Has anyone used this LANGS vaporizer conversion part ?
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Dave_Kriegel
Topic author - Posts: 74
- Joined: Sun May 05, 2019 8:50 am
- First Name: David
- Last Name: Kriegel
- * REQUIRED* Type and Year of Model Ts owned: 1927 1926
- Location: Indiana
- Board Member Since: 1999
Has anyone used this LANGS vaporizer conversion part ?
- Attachments
-
- 613s.jpg (2.3 KiB) Viewed 1924 times
-
RajoRacer
- Posts: 5175
- Joined: Sun Jan 06, 2019 12:18 pm
- First Name: Steve
- Last Name: Tomaso
- * REQUIRED* Type and Year of Model Ts owned: 1914 Touring, 1919 Centerdoor, 1924 TT C-Cab Express, 1925 Racer
- Location: Longbranch, WA
- Board Member Since: 2001
Re: Has anyone used this LANGS vaporizer conversion part ?
I've installed one - pretty straight forward installation - sorry - didn't take a photo.
-
DanTreace
- Posts: 3813
- Joined: Sun Jan 06, 2019 10:56 am
- First Name: Dan
- Last Name: Treace
- * REQUIRED* Type and Year of Model Ts owned: ‘12 open express,'23 cutoff, '27 touring
- Location: North Central FL
- Board Member Since: 2000
- Contact:
Re: Has anyone used this LANGS vaporizer conversion part ?
Found this photo on the web, shows the upper Y-piece, of an older design part, that bolts to the cylinder head. Throttle rod attaches to the lever part and the lower end fits to the NH carb.
This is the newest style design, seems a bit easier in attachment and operation, but haven't any experience with these pieces.
- 676443.jpg (57.37 KiB) Viewed 1880 times
This is the newest style design, seems a bit easier in attachment and operation, but haven't any experience with these pieces.
- Image 7-7-21 at 2.34 PM.jpeg (31.37 KiB) Viewed 1880 times
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
-
hbarbee
- Posts: 12
- Joined: Tue Jan 08, 2019 10:20 am
- First Name: Hurst
- Last Name: Barbee
- * REQUIRED* Type and Year of Model Ts owned: 1927 Runabout with Pickup Body
- Location: Sealy, TX
- Board Member Since: 2016
Re: Has anyone used this LANGS vaporizer conversion part ?
I recently installed it as part of the whole vaporizer to NH conversion kit that Langs offers.
Attached are pics of the upper and lower ends.
The upper is pretty straight forward. The lower is not. The tabs shown in the Langs picture did not come bent down and it took me a while to figure that out. Also since they did not provide a way to attach it to the carb, I found a small very flat headed bolt as shown. You also have to grind a little off of the area around the vertical post so it does not rub on the carb.
It works fine.
Regards,
Hurst
Attached are pics of the upper and lower ends.
The upper is pretty straight forward. The lower is not. The tabs shown in the Langs picture did not come bent down and it took me a while to figure that out. Also since they did not provide a way to attach it to the carb, I found a small very flat headed bolt as shown. You also have to grind a little off of the area around the vertical post so it does not rub on the carb.
It works fine.
Regards,
Hurst
- Attachments
-
-
-
Dave_Kriegel
Topic author - Posts: 74
- Joined: Sun May 05, 2019 8:50 am
- First Name: David
- Last Name: Kriegel
- * REQUIRED* Type and Year of Model Ts owned: 1927 1926
- Location: Indiana
- Board Member Since: 1999
Re: Has anyone used this LANGS vaporizer conversion part ?
Langs called in response to a question There are no detailed instructions They suggest I also buy part number 3535B a rod Thanks to all I will try it
-
hbarbee
- Posts: 12
- Joined: Tue Jan 08, 2019 10:20 am
- First Name: Hurst
- Last Name: Barbee
- * REQUIRED* Type and Year of Model Ts owned: 1927 Runabout with Pickup Body
- Location: Sealy, TX
- Board Member Since: 2016
Re: Has anyone used this LANGS vaporizer conversion part ?
You may or may not need the rod. The one they provided with the "kit" did not fit so I bent and reused the one I had on the vaporizer carb.