Stamped logo
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Topic author - Posts: 1906
- Joined: Tue Jan 08, 2019 12:22 am
- First Name: craig
- Last Name: leach
- * REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
- Location: Laveen Az
Stamped logo
I was thinking some one asked about this logo a while back. Anyone have knowlege of it. I found it on a small brake drum.
Craig.
Thanks . Craig.
-
- Posts: 354
- Joined: Tue Nov 01, 2022 6:46 am
- First Name: Mike
- Last Name: Cushway
- * REQUIRED* Type and Year of Model Ts owned: 1925 TT, 1926 TT, 1926 TT
- Location: Trout Creek, MI
Re: Stamped logo
Craig,
Was it me you are thinking of? I asked about this logo on my TT frame a while back.
Was it me you are thinking of? I asked about this logo on my TT frame a while back.
-
Topic author - Posts: 1906
- Joined: Tue Jan 08, 2019 12:22 am
- First Name: craig
- Last Name: leach
- * REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
- Location: Laveen Az
Re: Stamped logo
Hi Mike,
It could have been, but was thinking it was the same logo?? Thanks.
Craig.
It could have been, but was thinking it was the same logo?? Thanks.
Craig.
-
- Posts: 3813
- Joined: Sun Jan 06, 2019 10:56 am
- First Name: Dan
- Last Name: Treace
- * REQUIRED* Type and Year of Model Ts owned: ‘12 open express,'23 cutoff, '27 touring
- Location: North Central FL
- Board Member Since: 2000
- Contact:
Re: Stamped logo
The frame marking is Parrish and Bingham. Ford supplier.
That other mark appears as Transue Williams, another supplier.
That other mark appears as Transue Williams, another supplier.
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
-
Topic author - Posts: 1906
- Joined: Tue Jan 08, 2019 12:22 am
- First Name: craig
- Last Name: leach
- * REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
- Location: Laveen Az
Re: Stamped logo
Thanks Dan,
Craig.
Craig.
-
- Posts: 6610
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
Re: Stamped logo
On our Canadian sourced cars the Transue Williams mark appears as a capital T superimposed over the W. This mark i have only found on forged parts, an so it is raised.
Allan from down under.
Allan from down under.
-
- Posts: 3813
- Joined: Sun Jan 06, 2019 10:56 am
- First Name: Dan
- Last Name: Treace
- * REQUIRED* Type and Year of Model Ts owned: ‘12 open express,'23 cutoff, '27 touring
- Location: North Central FL
- Board Member Since: 2000
- Contact:
Re: Stamped logo
Craig Leach wrote: ↑Tue Apr 18, 2023 9:29 pmI was thinking some one asked about this logo a while back. Anyone have knowlege of it. I found it on a small brake drum.stamped logo.jpg
Thanks .
Craig.
May not be Transue Williams. That same mark is seen on tools too, like this hub cap wrench, since your rear hub brake drum is a steel stamping, like the flat hub cap wrench, could be this mark in a triangle is Weston Mott. They were a stamping concern.
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
-
Topic author - Posts: 1906
- Joined: Tue Jan 08, 2019 12:22 am
- First Name: craig
- Last Name: leach
- * REQUIRED* Type and Year of Model Ts owned: 1919 Firetruck/1922 Speedster
- Location: Laveen Az
Re: Stamped logo
Thanks guys,
Looks like it most likely is a O.E.M. part. I thought it might be a after market because it doesn't look like it has any wear to speak of.
Craig.
Looks like it most likely is a O.E.M. part. I thought it might be a after market because it doesn't look like it has any wear to speak of.
Craig.