Axle taper

Discuss all things Model T related.
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules

Topic author
SteveD
Posts: 111
Joined: Fri Nov 05, 2021 2:11 pm
First Name: steven
Last Name: davidson
* REQUIRED* Type and Year of Model Ts owned: 1924 touring
Location: Roselle NJ

Axle taper

Post by SteveD » Wed Sep 13, 2023 12:38 pm

Can someone tell me the taper on the end of an axle?

User avatar

George Mills
Posts: 620
Joined: Sun Jan 06, 2019 12:32 pm
First Name: George
Last Name: Mills
* REQUIRED* Type and Year of Model Ts owned: 1915 Roadster, 1919 Hack, 1925 Fordor
Location: Cherry Hill NJ/Anona Largo FL
Board Member Since: 1999

Re: Axle taper

Post by George Mills » Wed Sep 13, 2023 12:58 pm

maybe this helps?
axle for T.png


jab35
Posts: 1001
Joined: Sun Jan 06, 2019 12:28 pm
First Name: James
Last Name: Bartsch
* REQUIRED* Type and Year of Model Ts owned: '26 Coupe
Location: Dryden, NY 13053
MTFCA Life Member: YES

Re: Axle taper

Post by jab35 » Wed Sep 13, 2023 2:45 pm

This post mentions a taper of 1.5 inches/foot.
https://www.mtfca.com/discus/messages/2 ... 0tolerance.

For the dimensions shown in the drawing in this post, the taper is 3.546 degrees
A 1.5 inch change in diameter per foot of length gives a taper angle of 3.576 degrees
Respectfully, jb


speedytinc
Posts: 4728
Joined: Fri Feb 12, 2021 12:24 pm
First Name: john
Last Name: karvaly
* REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
Location: orange, ca
Board Member Since: 2020

Re: Axle taper

Post by speedytinc » Wed Sep 13, 2023 3:39 pm

A little trig work, I come up with 3 degrees 15 minutes. Or 3.25 degrees/side. 6.5 degrees total

User avatar

DanTreace
Posts: 3813
Joined: Sun Jan 06, 2019 10:56 am
First Name: Dan
Last Name: Treace
* REQUIRED* Type and Year of Model Ts owned: ‘12 open express,'23 cutoff, '27 touring
Location: North Central FL
Board Member Since: 2000
Contact:

Re: Axle taper

Post by DanTreace » Wed Sep 13, 2023 5:32 pm

SteveD wrote:
Wed Sep 13, 2023 12:38 pm
Can someone tell me the taper on the end of an axle?
1 1/2" per foot. Ford axle drawing.

Axle detail keyway.jpg
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford


Topic author
SteveD
Posts: 111
Joined: Fri Nov 05, 2021 2:11 pm
First Name: steven
Last Name: davidson
* REQUIRED* Type and Year of Model Ts owned: 1924 touring
Location: Roselle NJ

Re: Axle taper

Post by SteveD » Wed Sep 13, 2023 8:30 pm

Thanks guys

Post Reply Previous topicNext topic