What would normally have been used for the roof covering for a light delivery
or depot hack ?
Roof Covering
Forum rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
If you need help logging in, or have question about how something works, use the Support forum located here Support Forum
Complete set of Forum Rules Forum Rules
-
Henry K. Lee
- Posts: 5618
- Joined: Sun Jan 06, 2019 11:09 am
- First Name: Henry
- Last Name: Lee
- * REQUIRED* Type and Year of Model Ts owned: Many
- Location: South Pittsburg, TN
- MTFCA Life Member: YES
Re: Roof Covering
Cobra vinyl or a light rubberized canvas are the two that are commonly used today.
-
DanTreace
- Posts: 4082
- Joined: Sun Jan 06, 2019 10:56 am
- First Name: Dan
- Last Name: Treace
- * REQUIRED* Type and Year of Model Ts owned: '23 cutoff pickup, '27 touring
- Location: North Central FL
- Board Member Since: 2000
- Contact:
Re: Roof Covering
Catalog page details top construction.
The best way is always the simplest. The attics of the world are cluttered up with complicated failures. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
Don’t find fault, find a remedy; anybody can complain. Henry Ford
-
kevinf
- Posts: 147
- Joined: Sun Jan 13, 2019 9:17 pm
- First Name: Kevin
- Last Name: Fielding
- Location: Ewe-taw
Re: Roof Covering
John,
When I did my depot hack, I used the long grain cobra, (Snyders A-47300). I built the roof out of lath that was beaded to resemble wainscoting from the inside. I then routed the out side edge with a 3/4" rounding bit in the router. I covered this with a piece of 1/4" closed cell foam I purchased from a local upholstery shop. When I purchased the foam, the guy gave me a tip to leave the foam hanging about 1/2" over the edge of the top, and then take a razor blade and chamfer the underneath side of the foam. When you pull the top material over the edge it creates a nice smooth transition. I finished off the project with hydem-welting.
On a side note, the day I stretched the fabric, I hosted our local Model A club to help pull the fabric while I stapled. Many of the members that helped are no longer with us, but the memories we made that day were priceless.
Hope that helps. Kevin
When I did my depot hack, I used the long grain cobra, (Snyders A-47300). I built the roof out of lath that was beaded to resemble wainscoting from the inside. I then routed the out side edge with a 3/4" rounding bit in the router. I covered this with a piece of 1/4" closed cell foam I purchased from a local upholstery shop. When I purchased the foam, the guy gave me a tip to leave the foam hanging about 1/2" over the edge of the top, and then take a razor blade and chamfer the underneath side of the foam. When you pull the top material over the edge it creates a nice smooth transition. I finished off the project with hydem-welting.
On a side note, the day I stretched the fabric, I hosted our local Model A club to help pull the fabric while I stapled. Many of the members that helped are no longer with us, but the memories we made that day were priceless.
Hope that helps. Kevin
-
Allan
- Posts: 7263
- Joined: Sun Jan 06, 2019 7:21 pm
- First Name: Allan
- Last Name: Bennett
- * REQUIRED* Type and Year of Model Ts owned: 1912 van, 1917 shooting brake, 1929 roadster buckboard, 1924 tourer, 1925 barn find buckboard, 1925 D &F wide body roadster, 1927LHD Tudor sedan.
- Location: Gawler, Australia
Re: Roof Covering
Most of our Colonial built car bodies had light coloured canvas tops rather than black vinyl type covering. I used canvas over cedar laths on both my 1912 van and 19 17 shooting brake. Modern canvas fabric contains a percentage of polyester fibre in the yarn which makes it longer lasting, stronger and less liable to shrinkage. The one one my van is 33 years old now and is still as god as the day it was fitted.
My motor trimmer advised against using foam as an underlayer because some types decay under hot conditions. He put me onto the dacron sheeting used by quilters. It is stable, does not shrink, is not affected by moisture and is available in multiple widths. I used 1/4" thick stuff so the top does not look padded out on the sides where it is finished.
Allan from down under.
My motor trimmer advised against using foam as an underlayer because some types decay under hot conditions. He put me onto the dacron sheeting used by quilters. It is stable, does not shrink, is not affected by moisture and is available in multiple widths. I used 1/4" thick stuff so the top does not look padded out on the sides where it is finished.
Allan from down under.
- Attachments
-
-
-
-