WTB: Or (Borrow One). Camshaft rear bearing reamer bar that is put through the camshaft journals to align bore the rear bearing. Just trying to rebuild my T engine the proper way. I don't have a lathe to make one, any help would be appreciated!
Thanks, John
Camshaft Rear Bearing Reamer Bar
-
BRENT in 10-uh-C
- Posts: 471
- Joined: Mon Jan 07, 2019 11:21 am
- First Name: Brent
- Last Name: Terry
- * REQUIRED* Type and Year of Model Ts owned: 1909 Tourabout, 1914 Runabout, 1914 Touring, 1916 Speedster, 1925 Speedster, 1926 Hack
- Location: Eastern Tennessee
- Board Member Since: 1999
- Contact:
Re: Camshaft Rear Bearing Reamer Bar
Do you have a picture??
Last edited by BRENT in 10-uh-C on Wed Feb 04, 2026 9:18 am, edited 1 time in total.
-
cwhuntersr
- Posts: 30
- Joined: Mon Nov 20, 2023 3:58 pm
- First Name: CW
- Last Name: Hunter
- * REQUIRED* Type and Year of Model Ts owned: 1927 Roadster Pickup
- Location: Frederick, md
Re: Camshaft Rear Bearing Reamer Bar
You can see one in this thread: http://www.mtfca.com/discus/messages/50 ... 1224785762
-
Dan Hatch
- Posts: 5446
- Joined: Tue Jan 08, 2019 7:31 pm
- First Name: Dan
- Last Name: Hatch
- Location: Alabama
Re: Camshaft Rear Bearing Reamer Bar
Pictures worth a thousand words
-
Jeepbone1
- Posts: 627
- Joined: Sun Jan 06, 2019 6:10 pm
- First Name: Brad
- Last Name: Kirtner
- * REQUIRED* Type and Year of Model Ts owned: 1924 Touring Car, 1927 Closed Cab TT, 1927 Coupe
- Location: Salem, Virginia
- Board Member Since: 2018
Re: Camshaft Rear Bearing Reamer Bar
This is mine. I have multiple standard and undersized reamers. I think these are jig bore reamers. Had it made so it can be powered by a drill motor, wrench or piece of bar stock. Cost about $250 to have it made locally. May be a little too far from you though.
Brad
Brad
- Attachments
-
-
-
-
vanco
Topic author - Posts: 27
- Joined: Wed Apr 10, 2019 5:58 pm
- First Name: John
- Last Name: Van Cott
- Location: Utah
Re: Camshaft Rear Bearing Reamer Bar
Thanks for the photo's and information! To my knowledge there are not any model t ford clubs in Utah so I joined the MTFCA so that I have some information flow. Possibly I can find a machine shop in the area that would consider making one, most shops I have found do not have the time or interest in model t fords. It is all about available time and money. Thanks everyone, John
-
speedytinc
- Posts: 5190
- Joined: Fri Feb 12, 2021 12:24 pm
- First Name: john
- Last Name: karvaly
- * REQUIRED* Type and Year of Model Ts owned: 14/15 wide track roadster. 23 touring, 27 roadster pickup, 20ish rajo touring
- Location: orange, ca
- Board Member Since: 2020
Re: Camshaft Rear Bearing Reamer Bar
Is this tool really necessary? Does every motor re-builder use one? Does the service manual refer to this procedure?
Do you have a reasonable suspension that your block's cam mounts are out of alignment?
Do you have a reasonable suspension that your block's cam mounts are out of alignment?
-
vanco
Topic author - Posts: 27
- Joined: Wed Apr 10, 2019 5:58 pm
- First Name: John
- Last Name: Van Cott
- Location: Utah
Re: Camshaft Rear Bearing Reamer Bar
I'm not sure, I guess that I should do some more research? I have seen Mike Bender use one on his engine rebuilds as well as others in the past. My engine requires that a new bearing be installed.